Validation of implosion modeling through direct-drive shock timing experiments at the National Ignition Facility.

Precise modeling of shocks in inertial confinement fusion implosions is critical for obtaining the desired compression in experiments. Shock velocities and postshock conditions are determined by laser-energy deposition, heat conduction, and equations of state. This paper describes experiments at the National Ignition Facility (NIF) [E. M. Campbell and W. J. Hogan, Plasma Phys. Control. Fusion 41, B39 (1999)10.1088/0741-3335/41/12B/303] where multiple shocks are launched into a cone-in-shell target made of polystyrene, using laser-pulse shapes with two or three pickets and varying on-target intensities. Shocks are diagnosed using the velocity interferometric system for any reflector (VISAR) diagnostic [P. M. Celliers et al., Rev. Sci. Instrum. 75, 4916 (2004)0034-674810.1063/1.1807008]. Simulated and inferred shock velocities agree well for the range of intensities studied in this work. These directly-driven shock-timing experiments on the NIF provide a good measure of early-time laser-energy coupling. The validated models add to the credibility of direct-drive-ignition designs at the megajoule scale.

Light-enhanced oxygen degradation of MAPbBr3 single crystal.

Organometal halide perovskites are promising materials for optoelectronic applications, whose commercial realization depends critically on their stability under multiple environmental factors. In this study, a methylammonium lead bromide (MAPbBr3) single crystal was cleaved and exposed to simultaneous oxygen and light illumination under ultrahigh vacuum (UHV). The exposure process was monitored using X-ray photoelectron spectroscopy (XPS) with precise control of the exposure time and oxygen pressure. It was found that the combination of oxygen and light accelerated the degradation of MAPbBr3, which could not be viewed as a simple addition of that by oxygen-only and light-only exposures. The XPS spectra showed significant loss of carbon, bromine, and nitrogen at an oxygen exposure of 1010 Langmuir with light illumination, approximately 17 times of the additive effects of oxygen-only and light-only exposures. It was also found that the photoluminescence (PL) emission was much weakened by oxygen and light co-exposure, while previous reports had shown that PL was substantially enhanced by oxygen-only exposure. Measurements using a scanning electron microscope (SEM) and focused ion beam (FIB) demonstrated that the crystal surface was much roughened by the co-exposure. Density functional theory (DFT) calculations revealed the formation of superoxide and oxygen induced gap state, suggesting the creation of oxygen radicals by light illumination as a possible microscopic driving force for enhanced degradation.

Laser-direct-drive fusion target design with a high-Z gradient-density pusher shell.

Laser-direct-drive fusion target designs with solid deuterium-tritium (DT) fuel, a high-Z gradient-density pusher shell (GDPS), and a Au-coated foam layer have been investigated through both 1D and 2D radiation-hydrodynamic simulations. Compared with conventional low-Z ablators and DT-push-on-DT targets, these GDPS targets possess certain advantages of being instability-resistant implosions that can be high adiabat (α≥8) and low hot-spot and pusher-shell convergence (CR_{hs}≈22 and CR_{PS}≈17), and have a low implosion velocity (v_{imp}<3×10^{7}cm/s). Using symmetric drive with laser energies of 1.9 to 2.5MJ, 1D lilac simulations of these GDPS implosions can result in neutron yields corresponding to ≳50-MJ energy, even with reduced laser absorption due to the cross-beam energy transfer (CBET) effect. Two-dimensional draco simulations show that these GDPS targets can still ignite and deliver neutron yields from 4 to ∼10MJ even if CBET is present, while traditional DT-push-on-DT targets normally fail due to the CBET-induced reduction of ablation pressure. If CBET is mitigated, these GDPS targets are expected to produce neutron yields of >20MJ at a driven laser energy of ∼2MJ. The key factors behind the robust ignition and moderate energy gain of such GDPS implosions are as follows: (1) The high initial density of the high-Z pusher shell can be placed at a very high adiabat while the DT fuel is maintained at a relatively low-entropy state; therefore, such implosions can still provide enough compression ρR>1g/cm^{2} for sufficient confinement; (2) the high-Z layer significantly reduces heat-conduction loss from the hot spot since thermal conductivity scales as ∼1/Z; and (3) possible radiation trapping may offer an additional advantage for reducing energy loss from such high-Z targets.

Time-dependent density-functional-theory calculations of the nonlocal electron stopping range for inertial confinement fusion applications.

Nonlocal electron transport is important for understanding laser-target coupling for laser-direct-drive (LDD) inertial confinement fusion (ICF) simulations. Current models for the nonlocal electron mean free path in radiation-hydrodynamic codes are based on plasma-physics models developed decades ago; improvements are needed to accurately predict the electron conduction in LDD simulations of ICF target implosions. We utilized time-dependent density functional theory (TD-DFT) to calculate the electron stopping power (SP) in the so-called conduction-zone plasmas of polystyrene in a wide range of densities and temperatures relevant to LDD. Compared with the modified Lee-More model, the TD-DFT calculations indicated a lower SP and a higher stopping range for nonlocal electrons. We fit these electron SP calculations to obtain a global analytical model for the electron stopping range as a function of plasma conditions and the nonlocal electron kinetic energy. This model was implemented in the one-dimensional radiation-hydrodynamic code lilac to perform simulations of LDD ICF implosions, which are further compared with simulations by the standard modified Lee-More model. Results from these integrated simulations are discussed in terms of the implications of this TD-DFT-based mean-free-path model to ICF simulations.

[Impact of VA-ECMO combined with IABP and timing on outcome of patients with acute myocardial infarction complicated with cardiogenic shock].

Objective: To investigate the impact of combined use and timing of arterial-venous extracorporeal membrane oxygenation (VA-ECMO) with intra-aortic balloon pump (IABP) on the prognosis of patients with acute myocardial infarction complicated with cardiogenic shock (AMICS). Methods: This was a prospective cohort study, patients with acute myocardial infarction and cardiogenic shock who received VA-ECMO support from the Heart Center of Lanzhou University First Hospital from March 2019 to March 2022 in the registration database of the Chinese Society for Extracorporeal Life Support were enrolled. According to combination with IABP and time point, patients were divided into VA-ECMO alone group, VA-ECMO+IABP concurrent group and VA-ECMO+IABP non-concurrent group. Data from 3 groups of patients were collected, including the demographic characteristics, risk factors, ECG and echocardiographic examination results, critical illness characteristics, coronary intervention results, VA-ECMO related parameters and complications were compared among the three groups. The primary clinical endpoint was all-cause death, and the safety indicators of mechanical circulatory support included a decrease in hemoglobin greater than 50 g/L, gastrointestinal bleeding, bacteremia, lower extremity ischemia, lower extremity thrombosis, acute kidney injury, pulmonary edema and stroke. Kaplan-Meier survival curves were used to analyze the survival outcomes of patients within 30 days of follow-up. Using VA-ECMO+IABP concurrent group as reference, multivariate Cox regression model was used to evaluate the effect of the combination of VA-ECMO+IABP at different time points on the prognosis of AMICS patients within 30 days. Results: The study included 68 AMICS patients who were supported by VA-ECMO, average age was (59.8±10.8) years, there were 12 female patients (17.6%), 19 cases were in VA-ECMO alone group, 34 cases in VA-ECMO+IABP concurrent group and 15 cases in VA-ECMO+IABP non-concurrent group. The success rate of ECMO weaning in the VA-ECMO+IABP concurrent group was significantly higher than that in the VA-ECMO alone group and the VA-ECMO+IABP non-concurrent group (all P<0.05). Compared with the ECMO+IABP non-concurrent group, the other two groups had shorter ECMO support time, lower rates of acute kidney injury complications (all P<0.05), and lower rates of pulmonary edema complications in the ECMO alone group (P<0.05). In-hospital survival rate was significantly higher in the VA-ECMO+IABP concurrent group (28 patients (82.4%)) than in the VA-ECMO alone group (9 patients) and VA-ECMO+IABP non-concurrent group (7 patients) (all P<0.05). The survival rate up to 30 days of follow-up was also significantly higher surviving patients within were in the ECMO+IABP concurrent group (26 cases) than in VA-ECMO alone group (9 patients) and VA-ECMO+IABP non-concurrent group (4 patients) (all P<0.05). Multivariate Cox regression analysis showed that compared with the concurrent use of VA-ECMO+IABP, the use of VA-ECMO alone and non-concurrent use of VA-ECMO+IABP were associated with increased 30-day mortality in AMICS patients (HR=2.801, P=0.036; HR=2.985, P=0.033, respectively). Conclusions: When VA-ECMO is indicated for AMICS patients, combined use with IABP at the same time can improve the ECMO weaning rate, in-hospital survival and survival at 30 days post discharge, and which does not increase additional complications.

Measuring the principal Hugoniot of inertial-confinement-fusion-relevant TMPTA plastic foams.

Wetted-foam layers are of significant interest for inertial-confinement-fusion capsules, due to the control they provide over the convergence ratio of the implosion and the opportunity this affords to minimize hydrodynamic instability growth. However, the equation of state for fusion-relevant foams are not well characterized, and many simulations rely on modeling such foams as a homogeneous medium with the foam average density. To address this issue, an experiment was performed using the VULCAN Nd:glass laser at the Central Laser Facility. The aim was to measure the principal Hugoniot of TMPTA plastic foams at 260mg/cm^{3}, corresponding to the density of liquid DT-wetted-foam layers, and their "hydrodynamic equivalent" capsules. A VISAR was used to obtain the shock velocity of both the foam and an α-quartz reference layer, while streaked optical pyrometry provided the temperature of the shocked material. The measurements confirm that, for the 20-120 GPa pressure range accessed, this material can indeed be well described using the equation of state of the homogeneous medium at the foam density.

Cooperative diffusion in body-centered cubic iron in Earth and super-Earths' inner core conditions.

The physical chemistry of iron at the inner-core conditions is key to understanding the evolution and habitability of Earth and super-Earth planets. Based on full first-principles simulations, we report cooperative diffusion along the longitudinally fast⟨111⟩directions of body-centered cubic (bcc) iron in temperature ranges of up to 2000-4000 K below melting and pressures of ∼300-4000 GPa. The diffusion is due to the low energy barrier in the corresponding direction and is accompanied by mechanical and dynamical stability, as well as strong elastic anisotropy of bcc iron. These findings provide a possible explanation for seismological signatures of the Earth's inner core, particularly the positive correlation between P wave velocity and attenuation. The diffusion can also change the detailed mechanism of core convection by increasing the diffusivity and electrical conductivity and lowering the viscosity. The results need to be considered in future geophysical and planetary models and should motivate future studies of materials under extreme conditions.

Probing atomic physics at ultrahigh pressure using laser-driven implosions.

Spectroscopic measurements of dense plasmas at billions of atmospheres provide tests to our fundamental understanding of how matter behaves at extreme conditions. Developing reliable atomic physics models at these conditions, benchmarked by experimental data, is crucial to an improved understanding of radiation transport in both stars and inertial fusion targets. However, detailed spectroscopic measurements at these conditions are rare, and traditional collisional-radiative equilibrium models, based on isolated-atom calculations and ad hoc continuum lowering models, have proved questionable at and beyond solid density. Here we report time-integrated and time-resolved x-ray spectroscopy measurements at several billion atmospheres using laser-driven implosions of Cu-doped targets. We use the imploding shell and its hot core at stagnation to probe the spectral changes of Cu-doped witness layer. These measurements indicate the necessity and viability of modeling dense plasmas with self-consistent methods like density-functional theory, which impact the accuracy of radiation transport simulations used to describe stellar evolution and the design of inertial fusion targets.

First-principles equation of state of CHON resin for inertial confinement fusion applications.

A wide-range (0 to 1044.0 g/cm^{3} and 0 to 10^{9} K) equation-of-state (EOS) table for a CH_{1.72}O_{0.37}N_{0.086} quaternary compound has been constructed based on density-functional theory (DFT) molecular-dynamics (MD) calculations using a combination of Kohn-Sham DFT MD, orbital-free DFT MD, and numerical extrapolation. The first-principles EOS data are compared with predictions of simple models, including the fully ionized ideal gas and the Fermi-degenerate electron gas models, to chart their temperature-density conditions of applicability. The shock Hugoniot, thermodynamic properties, and bulk sound velocities are predicted based on the EOS table and compared to those of C-H compounds. The Hugoniot results show the maximum compression ratio of the C-H-O-N resin is larger than that of CH polystyrene due to the existence of oxygen and nitrogen; while the other properties are similar between CHON and CH. Radiation hydrodynamic simulations have been performed using the table for inertial confinement fusion targets with a CHON ablator and compared with a similar design with CH. The simulations show CHON outperforms CH as the ablator for laser-direct-drive target designs.

[A deep learning segmentation model for detecting caries in molar teeth].

This study aimed to build a home use deep learning segmentation model to identify the scope of caries lesions. A total of 494 caries photographs of molars and premolars collected via endoscopy were selected. Subsequently, these photographs were labeled by physicians and underwent segmentation training by using DeepLabv3+, and then verification and evaluation were performed. The mean accuracy was 0.993, the sensitivity was 0.661, the specificity was 0.997, the Dice coefficient was 0.685, and the intersection over union (IoU) was 0.529. Therefore, the present deep learning segmentation model can identify and segment the scope of caries.

Bound on hot-spot mix in high-velocity, high-adiabat direct-drive cryogenic implosions based on comparison of absolute x-ray and neutron yields.

In laser-driven implosions for laboratory fusion, the comparison of hot-spot x-ray yield to neutron production can serve to infer hot-spot mix. For high-performance direct-drive implosions, this ratio depends sensitively on the degree of equilibration between the ion and electron fluids. A scaling for x-ray yield as a function of neutron yield and characteristic ion and electron hot-spot temperatures is developed on the basis of simulations with varying degrees of equilibration. We apply this model to hot-spot x-ray measurements of direct-drive cryogenic implosions typical of the direct-drive designs with best ignition metrics. The comparison of the measured x-ray and neutron yields indicates that hot-spot mix, if present, is below a sensitivity estimated as ∼2% by-atom mix of ablator plastic into the hot spot.

Proton stopping measurements at low velocity in warm dense carbon.

Ion stopping in warm dense matter is a process of fundamental importance for the understanding of the properties of dense plasmas, the realization and the interpretation of experiments involving ion-beam-heated warm dense matter samples, and for inertial confinement fusion research. The theoretical description of the ion stopping power in warm dense matter is difficult notably due to electron coupling and degeneracy, and measurements are still largely missing. In particular, the low-velocity stopping range, that features the largest modelling uncertainties, remains virtually unexplored. Here, we report proton energy-loss measurements in warm dense plasma at unprecedented low projectile velocities. Our energy-loss data, combined with a precise target characterization based on plasma-emission measurements using two independent spectroscopy diagnostics, demonstrate a significant deviation of the stopping power from classical models in this regime. In particular, we show that our results are in closest agreement with recent first-principles simulations based on time-dependent density functional theory.

Mixed stochastic-deterministic time-dependent density functional theory: application to stopping power of warm dense carbon.

Warm dense matter (WDM) describes an intermediate phase, between condensed matter and classical plasmas, found in natural and man-made systems. In a laboratory setting, WDM is often created dynamically. It is typically laser or pulse-power generated and can be difficult to characterize experimentally. Measuring the energy loss of high energy ions, caused by a WDM target, is both a promising diagnostic and of fundamental importance to inertial confinement fusion research. However, electron coupling, degeneracy, and quantum effects limit the accuracy of easily calculable kinetic models for stopping power, while high temperatures make the traditional tools of condensed matter, e.g. time-dependent density functional theory (TD-DFT), often intractable. We have developed a mixed stochastic-deterministic approach to TD-DFT which provides more efficient computation while maintaining the required precision for model discrimination. Recently, this approach showed significant improvement compared to models when compared to experimental energy loss measurements in WDM carbon. Here, we describe this approach and demonstrate its application to warm dense carbon stopping across a range of projectile velocities. We compare direct stopping-power calculation to approaches based on combining homogeneous electron gas response with bound electrons, with parameters extracted from our TD-DFT calculations.

First-principles study of L-shell iron and chromium opacity at stellar interior temperatures.

Recently developed free-energy density functional theory (DFT)-based methodology for optical property calculations of warm dense matter has been applied for studying L-shell opacity of iron and chromium at T=182 eV. We use Mermin-Kohn-Sham density functional theory with a ground-state and a fully-temperature-dependent generalized gradient approximation exchange-correlation (XC) functionals. It is demonstrated that the role of XC at such a high-T is negligible due to the total free energy of interacting systems being dominated by the noninteracting free-energy term, in agreement with estimations for the homogeneous electron gas. Our DFT predictions are compared with the radiative emissivity and opacity of the dense plasma model, with the real-space Green's function method, and with experimental measurements. Good agreement is found between all three theoretical methods, and in the bound-continuum region for Cr when compared with the experiment, while the discrepancy between direct DFT calculations and the experiment for Fe remains essentially the same as for plasma-physics models.

Ionization state and dielectric constant in cold rarefied hydrocarbon plasmas of inertial confinement fusion.

A combined approach to study cold rarefied matter is introduced that includes a semianalytical method based on the free-energy minimization and ab initio calculations based on the finite-temperature density-functional theory. The approach is used to calculate the ionization state of hydrocarbon (CH) under the shock-release conditions in inertial confinement fusion. The dielectric constant of CH is calculated using the Kubo-Greenwood formulation and contribution from atomic polarizabilities is found to be as important as the free-electron contribution. Using the ionization state and dielectric constant, the electron density profile in the rarefaction wave of the shock-release plasma is obtained.

Experimentally Inferred Fusion Yield Dependencies of OMEGA Inertial Confinement Fusion Implosions.

Statistical modeling of experimental and simulation databases has enabled the development of an accurate predictive capability for deuterium-tritium layered cryogenic implosions at the OMEGA laser [V. Gopalaswamy et al.,Nature 565, 581 (2019)10.1038/s41586-019-0877-0]. In this letter, a physics-based statistical mapping framework is described and used to uncover the dependencies of the fusion yield. This model is used to identify and quantify the degradation mechanisms of the fusion yield in direct-drive implosions on OMEGA. The yield is found to be reduced by the ratio of laser beam to target radius, the asymmetry in inferred ion temperatures from the ℓ=1 mode, the time span over which tritium fuel has decayed, and parameters related to the implosion hydrodynamic stability. When adjusted for tritium decay and ℓ=1 mode, the highest yield in OMEGA cryogenic implosions is predicted to exceed 2×10^{14} fusion reactions.

Improved modeling of the solid-to-plasma transition of polystyrene ablator for laser direct-drive inertial confinement fusion hydrocodes.

The target performance of laser direct-drive inertial confinement fusion (ICF) can be limited by the development of hydrodynamic instabilities resulting from the nonhomegeneous laser absorption at the target surface, i.e., the laser imprint on the ablator. To understand and describe the formation of these instabilities, the early ablator evolution during the laser irradiation should be considered. In this work, an improved modeling of the solid-to-plasma transition of a polystyrene ablator for laser direct-drive ICF is proposed. This model is devoted to be implemented in hydrocodes dedicated to ICF which generally assume an initial plasma state. The present approach consists of the two-temperature model coupled to the electron, ion and neutral dynamics including the chemical fragmentation of polystyrene. The solid-to-plasma transition is shown to significantly influence the temporal evolution of both free electron density and temperatures, which can lead to different shock formation and propagation compared with an initial plasma state. The influence of the solid-to-plasma transition on the shock dynamics is evidenced by considering the scaling law of the pressure with respect to the laser intensity. The ablator transition is shown to modify the scaling law exponent compared with an initial plasma state.

Unraveling the intrinsic atomic physics behind x-ray absorption line shifts in warm dense silicon plasmas.

We present a free-energy density functional theory (DFT)-based methodology for optical property calculations of warm dense matter to cover a wide range of thermodynamic conditions and photon energies including the entire x-ray range. It uses Mermin-Kohn-Sham density functional theory with exchange-correlation (XC) thermal effects taken into account via a fully temperature dependent generalized gradient approximation XC functional. The methodology incorporates a combination of the ab initio molecular dynamics (AIMD) snapshotted Kubo-Greenwood optic data with a single atom in simulation cell calculations to close the photon energy gap between the L and K edges and extend the K-edge tail toward many-keV photon energies. This gap arises in the standard scheme due to a prohibitively large number of bands required for the Kubo-Greenwood calculations with AIMD snapshots. Kubo-Greenwood data on snapshots provide an accurate description of optic properties at low photon frequencies slightly beyond the L edge and x-ray absorption near edges structure (XANES) spectra, while data from periodic calculations with single atoms cover the tail regions beyond the edges. To demonstrate its applicability to mid-Z materials where the standard DFT-based approach is not computationally feasible, we have applied it to opacity calculations of warm dense silicon plasmas. These first-principles calculations revealed a very interesting phenomenon of redshift-to-blueshift in K-L (1s→2p) and K-edge absorptions along both isotherm and isochore, which are absent in most continuum-lowering models of traditional plasma physics. This new physics phenomenon can be attributed to the underlying competition between the screening of deeply bound core electrons and the screening of outer-shell electrons caused by warm-dense-plasma conditions. We further demonstrate that the ratio of 1s→2p to the K-edge x-ray absorptions can be used to characterize warm-dense-plasma conditions. Eventually, based on our absorption calculations, we have established a first-principles opacity table (FPOT) for silicon in a wide range of material densities and temperatures.