Enhanced and Proficient Soft Template Array of Polyaniline-TiO2 Nanocomposites Fibers Prepared Using Anionic Surfactant for Fuel Cell Hydrogen Storage.

Porous TiO2-doped polyaniline and polyaniline nanocomposite fibers prepared by the in situ polymerization technique using anionic surfactant in an ice bath were studied. The prepared nanocomposites were characterized by FTIR spectroscopy and XRD patterns for structural analysis. The surface morphology of the polyaniline and its nanocomposites was examined using SEM images. DC conductivity shows the three levels of conductivity inherent in a semiconductor. Among the nanocomposites, the maximum DC conductivity is 5.6 S/cm for 3 wt.% polyaniline-TiO2 nanocomposite. Cyclic voltammetry shows the properties of PANI due to the redox peaks of 0.93 V and 0.24 V. Both peaks are due to the redox transition of PANI from the semiconductor to the conductive state. The hydrogen absorption capacity is approximately 4.5 wt.%, but at 60 °C the capacity doubles to approximately 7.3 wt.%. Conversely, 3 wt.% PANI-TiO2 nanocomposites have a high absorption capacity of 10.4 wt.% compared to other nanocomposites. An overall desorption capacity of 10.4 wt.% reduced to 96% was found for 3 wt.% TiO2-doped PANI nanocomposites.

Preparation of Anionic Surfactant-Based One-Dimensional Nanostructured Polyaniline Fibers for Hydrogen Storage Applications.

Polyaniline fibers were prepared in the presence of anionic surfactant in an ice medium to nucleate in one dimension and were compared to bulk polyaniline prepared at an optimum temperature. Fourier-transform infrared spectroscopy (FTIR) and X-ray powder diffraction (XRD) were used to investigate the structural analysis of the prepared samples. A conductivity study reveals that polyaniline fibers have high conductivity compared to bulk polyaniline. Hydrogen storage measurements confirm that the polyaniline fibers adsorbed approximately 86% of the total actual capacity of 8-8.5 wt% in less than 9 min, and desorption occurs at a lower temperature, releasing approximately 1.5 wt% of the hydrogen gases when the pressure is reduced further to 1 bar.

Thermal effect on curved photovoltaic panels: Model validation and application in the Tabuk region.

This paper aimed to investigate the temperature effect on photovoltaic (PV) cell parameters. The PV cell parameters such as series and parallel resistances, diode ideality factor, and diode saturation current, are not considered in the reported stepwise modeling. The present work aims to improve available models used in the modeling and simulation of PV modules to support the researcher and power project developer. All the required temperature-dependent parameters are determined to model the simulated PV module with high accuracy using Simulink/MATLAB software. To validate the method, a 36-cell-50W solar panel with different radii of curvature is set up to assess solar power outputs under varying irradiance and temperature conditions. For the present application, the Tabuk region (Saudi Arabia) is chosen based on its location and climatic conditions. The method provided conformity to the measured power outputs for varying Global Horizontal Irradiance (GHI) and temperature conditions. The maximum power output of the PV module increases from 14.4 W to 25.8 W when the received solar power density varies from 307 W/m2 to 526 W/m2 depending on the level of curvature starting from a semi-cylindrical shape to a vaulted shape to a flat shape. The curved PV module shows slightly higher power variation with temperature as compared to the flat one. Above 25°C, the power output is about 20% less at a maximum temperature of 65°C. When the temperature drops below 25°C, the power outputs increase about 6% and 11.5% for corresponding temperatures of 15°C and 5°C, respectively.

Fabrication and Characterization of Flexible Solid Polymers Electrolytes for Supercapacitor Application.

In this work, solid flexible polymer blend electrolytes (PBE) composed of polyvinyl alcohol (PVA) and polyvinyl pyrrolidone (PVP) with different amounts of sodium thiocyanate (NaSCN) salt mixed in double-distilled water (solvent) are prepared via solution casting method. The obtained films are characterized using several techniques. The study of the surface morphology of the polymer blend salt complex films via the POM technique reveals the presence of amorphous regions due to the NaSCN effect. FTIR spectra studies confirm the complex formation between PVA, PVP, and NaSCN. The addition of 20 wt% NaSCN salt in the composition PVA: PVP (50:50 wt%) polymer blend matrix leads to an increase in the number of charge carriers and thus improves the ionic conductivity. The ionic conductivity of each polymer blend electrolyte was studied using the electrochemical impedance spectroscopy (EIS) method. The highest room temperature ionic conductivity of 8.1 × 10-5 S/cm S cm-1 is obtained for the composition of PVA: PVP (50:50 wt%) with 20 wt% NaSCN. LSV test shows the optimized ion-conducting polymer blend electrolyte is electrochemically stable up to 1.5 V. TNM analysis reveals that 99% of ions contribute for the conductivity against 1% of electrons only in the highly conductive polymer electrolyte PVA: PVP (50:50 wt%) + 20 wt% NaSCN. A supercapacitor device was fabricated using the optimized ion-conducting polymer blend film and graphene oxide (GO) coated electrodes. The GCD curve clearly reveals the behavior of an ideal capacitor with less Faradic process and low ESR value. The columbic efficiency of the GO-based system is found to be 100%, the GO-based electrode exhibits a specific capacitance of 12.15 F/g and the system delivers the charge for a long duration. The specific capacitance of the solid-state supercapacitor cell was found to be 13.28 F/g via the CV approach close to 14.25 F/g obtained with EIS data at low frequency.

Triple-phase boundary and power density enhancement in thin solid oxide fuel cells by controlled etching of the nickel anode.

Fabrication of microporous structures for the anode of a thin film solid oxide fuel cell (SOFC(s)) using controlled etching process has led us to increased power density and increased cell robustness. Micropores were etched in the nickel anode by both wet and electrochemical etching processes. The samples etched electrochemically showed incomplete etching of the nickel leaving linked nickel islands inside the pores. Samples which were wet- etched showed clean pores with no nickel island residues. Moreover, the sample with linked nickel islands in the anode pores showed higher output power density as compared to the sample with clean pores. This enhancement is related to the enlargement of the surface of contact between the fuel-anode-electrolyte (the triple-phase boundary).

Nanostructured thin solid oxide fuel cells with high power density.

Nanostructured thin film solid oxide fuel cells (SOFC) have been developed for reduced temperature operation, with high power density, and to be self reforming. A thin film electrolyte (1-2 microm thickness), e.g., yttria-stabilized zirconia (YSZ), is deposited on a nickel foil substrate. The electrolyte thin film is polycrystalline when deposited on a polycrystalline nickel foil substrate, and is (100) textured when deposited on an atomically textured nickel foil substrate. The Ni foil substrate is then converted into a porous SOFC anode by photolithographic patterning and etching to develop porosity. A composite La(0.5)Sr(0.5)CoO(3) cathode is then deposited on the thin film electrolyte. The resultant thin film hetero structure fuel cells have operated at a significantly reduced temperature: as low as 470 degrees C, with a maximum power density of 140 mW cm(-2) at 575 degrees C, and an efficiency of >50%. This drastic reduction in operating temperature for an SOFC now also allows for the use of hydrocarbon fuels without the need for a separate reformer as the nickel anode effectively dissociates hydrocarbons within this temperature range. These nanostructured fuel cells show excellent potential for high power density, small volume, high efficiency fuel cells for power generation applications.