Self-powered triboelectric nanogenerator sensor for detecting humidity level and monitoring ethanol variation in a simulated exhalation environment.

Respiration stands as a vital process reflecting physiological and pathological human health status. Exhaled breath analysis offers a facile, non-invasive, swift, and cost-effective approach for diagnosing and monitoring diseases by detecting concentration changes of specific biomarkers. In this study, we employed Polyethylene oxide/copper (I) oxide composite nanofibers (PCNFs), synthesized via the electrospinning method as the sensing material to measure ethanol levels (1-200 ppm) in an exhaled breath simulator environment. The integrated contact-separation triboelectric nanogenerator was utilized to power the self-powered PCNFs exhaled breath sensor. The PCNFs-based gas sensor demonstrates promising results with values of 0.9 and 3.2 for detecting 5 ppm and 200 ppm ethanol, respectively, in the presence of interfering gas at 90% relative humidity (RH). Notably, the sensor displayed remarkable ethanol selectivity, with ratios of 10:1 to methanol and 25:1 to acetone. Response and recovery times for 200 ppm ethanol at 90 RH% were rapid, at 2.7 s and 5.8 s, respectively. The PCNFs-based exhaled breath sensor demonstrated consistent and stable performance in practical conditions, showcasing its potential for integration into wearable devices. This self-powered breath sensor enabling continuous monitoring of lung cancer symptoms and facilitating compliance checks with legal alcohol consumption limits.

Green synthesize of copper nanoparticles on the cotton fabric as a self-regenerating and high-efficient plasmonic solar evaporator.

Harvesting solar energy, as a clean and abundant resource, in the photothermal process, is the winning point of solar steam generation (SSG) systems. Herein, copper plasmonic nanoparticles were synthesized through a green method via red sanders extraction on the cotton fabric as the reducing matrix. The prepared fabrics were analyzed using FESEM, EDS, XRD, PL, Raman, and contact angle. The treated fabric on the stitched PU foam with cotton yarns with bio-inspired jellyfish structure was used for heat localization and water transmission, simultaneously. The evaporation rate, enhancement, and conversion efficiency of the plasmonic SSG were 1.73 kg m-2 h-1, 179%, and ~ 98%, under one sun irradiation, respectively. The quality of the collected water was investigated via induced coupled plasma which presents the proper solar desalination (> 99.83% for filtration of Na+ ion). Regenerating features of the treated fabric along with the simple and cost-effective preparation method promises viable aspects of our system for large-scale applications.

Tunable Gain SnS2/InSe Van der Waals Heterostructure Photodetector.

Due to the favorable properties of two-dimensional materials such as SnS2, with an energy gap in the visible light spectrum, and InSe, with high electron mobility, the combination of them can create a novel platform for electronic and optical devices. Herein, we study a tunable gain SnS2/InSe Van der Waals heterostructure photodetector. SnS2 crystals were synthesized by chemical vapor transport method and characterized using X-ray diffraction and Raman spectroscopy. The exfoliated SnS2 and InSe layers were transferred on the substrate. This photodetector presents photoresponsivity from 14 mA/W up to 740 mA/W and detectivity from 2.2 × 108 Jones up to 3.35 × 109 Jones by gate modulation from 0 V to +70 V. Light absorption and the charge carrier generation mechanism were studied by the Silvaco TCAD software and the results were confirmed by our experimental observations. The rather high responsivity and visible spectrum response makes the SnS2/InSe heterojunction a potential candidate for commercial visible image sensors.

Design of effective self-powered SnS2/halide perovskite photo-detection system based on triboelectric nanogenerator by regarding circuit impedance.

Self-powered detectors based on triboelectric nanogenerators (TENG) have been considered because of their capability to convert ambient mechanical energy to electrical out-put signal, instead of conventional usage of electrochemical batteries as power sources. In this regard, the self-powered photodetectors have been designed through totally two lay out called passive and active circuit. in former model, impedance matching between the TENG and the resistance of the circuit's elements is crucial, which is not investigated systematically till now. In this paper, a cost effective novel planar photodetector (PD) based on heterojunction of SnS2 sheets and Cs0.05(FA0.83 MA0.17)0.95Pb(I0.83Br0.17)3 three cationic lead iodide based perovskite (PVK) layer fabricated which powered by graphene oxide (GO) paper and Kapton based contact-separated TENG (CS-TENG). To achieve the high performance of this device, the proper range of the load resistances in the circuit regards to TENG's characterization has been studied. In the next steps, the integrated self-powered photo-detection system was designed by applying Kapton/FTO and hand/FTO TENG, separately, in the proposed impedance matching circuit. The calculated D* of integrated self-powered SnS2/PVK supplied by tapping the Kapton and hand on FTO is 2.83 × 1010 and 1.10 × 1013 Jones under the 10 mW/cm2 of white light intensity, the investigations determine that for designing significate performance of self-powered PD supplied by TENG, the existence of the load resistance with the well match amount to the utilized TENG is crucial. Our results which can be generalized to other types of passive self-powered sensors, are substantial to both academia and industry concepts.

Enhanced Photoresponse and Wavelength Selectivity by SILAR-Coated Quantum Dots on Two-Dimensional WSe2 Crystals.

High-performance photodetectors play crucial roles as an essential tool in many fields of science and technology, such as photonics, imaging, spectroscopy, and data communications. Demands for desired efficiency and low-cost new photodetectors through facile manufacturing methods have become a long-standing challenge. We used a simple successive ionic layer adsorption and reaction (SILAR) method to synthesize CdS, CdSe, and PbS nanoparticles directly grown on WSe2 crystalline flakes. In addition to the excellent wavelength selectivity for (30 nm) CdS, (30 nm) CdSe, and (6 nm) PbS/WSe2 heterostructures, the hybrid devices presented an efficient photodetector with a photoresponsivity of 48.72 A/W, a quantum efficiency of 71%, and a response time of 2.5-3.5 ms. Considering the energy band bending structure and numerical simulation data, the electric field distribution at interfaces and photocarrier generation/recombination rates have been studied. The introduced fabrication strategy is fully compatible with the semiconductor industry process, and it can be used as a novel method for fabricating wavelength-tunable and high-performance photodetectors toward innovative optoelectronic applications.

Room temperature and high response ethanol sensor based on two dimensional hybrid nanostructures of WS2/GONRs.

Here in this research, room temperature ethanol and humidity sensors were prepared based on two dimensional (2D) hybrid nanostructures of tungsten di-sulfide (WS2) nanosheets and graphene oxide nanoribbons (GONRs) as GOWS. The characterization results based on scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (ESD), Raman spectroscopy and X-ray diffraction (XRD) analysis confirmed the hybrid formations. Ethanol sensing of drop-casted GOWS films on SiO2 substrate indicated increasing in gas response up to 5 and 55 times higher compared to pristine GONRs and WS2 films respectively. The sensing performance of GOWS hybrid nanostructures was investigated in different concentrations of WS2, and the highest response was about 126.5 at 1 ppm of ethanol in 40% relative humidity (R.H.) for WS2/GONRs molar ratio of 10. Flexibility of GOWS was studied on Kapton substrate with bending radius of 1 cm, and the gas response decreased less than 10% after 30th bending cycles. The high response and flexibility of the sensors inspired that GOWS are promising materials for fabrication of wearable gas sensing devices.

A graphene/TiS3 heterojunction for resistive sensing of polar vapors at room temperature.

The room temperature polar vapor sensing behavior of a graphene-TiS3 heterojunction material and TiS3 nanoribbons is described. The nanoribbons were synthesized via chemical vapor transport (CVT) and their structure was investigated by scanning electron microscopy, high resolution transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, Raman and Fourier transform infrared spectroscopies. The gas sensing performance was assessed by following the changes in their resistivities. Sensing devices were fabricated with gold contacts and with lithographically patterned graphene (Gr) electrodes in a heterojunction Gr-TiS3-Gr. The gold contacted TiS3 device has a rather linear I-V behavior while the Gr-TiS3-Gr heterojunction forms a contact with a higher Schottky barrier (250 meV). The I-V responses of the sensors were recorded at room temperature at a relative humidity of 55% and for different ethanol vapor concentrations (varying from 2 to 20 ppm). The plots indicate an increase in the resistance of Gr-TiS3-Gr due to adsorption of water and ethanol with a relatively high sensing response (~495% at 2 ppm). The results reveal that stable responses to 2 ppm concentrations of ethanol are achieved at room temperature. The response and recovery times are around 8 s and 72 s, respectively. Weaker responses are obtained for methanol and acetone. Graphical abstract Schematic representation of resistance sensor for detection of low concentration of ethanol vapor. The graphene and TiS3 nanoribbons were synthesized using chemical vapor deposition and chemical vapor transport technique respectively. The 2D graphene/TiS3 heterojunction device was fabricated to make a high response sensor due to their synergy effect.

Doxorubicin/Cisplatin-Loaded Superparamagnetic Nanoparticles As A Stimuli-Responsive Co-Delivery System For Chemo-Photothermal Therapy.

INTRODUCTION: To date, numerous iron-based nanostructures have been designed for cancer therapy applications. Although some of them were promising for clinical applications, few efforts have been made to maximize the therapeutic index of these carriers. Herein, PEGylated silica-coated iron oxide nanoparticles (PS-IONs) were introduced as multipurpose stimuli-responsive co-delivery nanocarriers for a combination of dual-drug chemotherapy and photothermal therapy. METHODS: Superparamagnetic iron oxide nanoparticles were synthesized via the sonochemical method and coated by a thin layer of silica. The nanostructures were then further modified with a layer of di-carboxylate polyethylene glycol (6 kDa) and carboxylate-methoxy polyethylene glycol (6 kDa) to improve their stability, biocompatibility, and drug loading capability. Doxorubicin (DOX) and cisplatin (CDDP) were loaded on the PS-IONs through the interactions between the drug molecules and polyethylene glycol. RESULTS: The PS-IONs demonstrated excellent cellular uptake, cytocompatibility, and hemocompatibility at the practical dosage. Furthermore, in addition to being an appropriate MRI agent, PS-IONs demonstrated superb photothermal property in 0.5 W/cm2 of 808 nm laser irradiation. The release of both drugs was effectively triggered by pH and NIR irradiation. As a result of the intracellular combination chemotherapy and 10 min of safe power laser irradiation, the highest cytotoxicity for iron-based nanocarriers (97.3±0.8%) was achieved. CONCLUSION: The results of this study indicate the great potential of PS-IONs as a multifunctional targeted co-delivery system for cancer theranostic application and the advantage of employing proper combination therapy for cancer eradication.

Optimization of CuIn1-XGaXS2 Nanoparticles and Their Application in the Hole-Transporting Layer of Highly Efficient and Stable Mixed-Halide Perovskite Solar Cells.

Inorganic hole-transport materials (HTMs) have been frequently applied in perovskite solar cells (PSCs) and are a promising solution to improve the poor stability of PSCs. In this study, we investigate solution-processed copper indium gallium disulfide (CIGS) nanocrystals (NCs) as a dopant-free inorganic HTM in n-i-p type PSCs. Moreover, Cs0.05(MA0.17-FA0.83)0.95Pb(I0.83Br0.17)3 mixed-halide perovskite with proper crystalline quality and long-time stability was utilized as the light-absorbing layer under ambient conditions. To optimize the cell performance and better charge extraction from the perovskite layer, the Ga concentration in the Cu(In1-XGaX)S2 composition was changed, and the X value was altered between 0.0 and 0.75. It was shown that the CIGS band gap enhances with increasing Ga content; thus, with tunable band gaps and engineering of the energy level alignment, a better collection of photogenerated holes and a reduced electron-hole recombination rate could be achieved. The maximum power conversion efficiency of 15.6% was obtained for the PSC with Cu(In0.5Ga0.5)S2 hole-transport layer composition, which is the highest efficiency reported so far for CIGS-based dopant-free PSCs. This value is very close to the efficiency of devices fabricated with doped spiro-OMeTAD as an organic HTM. Additionally, the stability of nonencapsulated PSCs was studied, and CIGS-based devices demonstrated 70% retention after 90 days of aging in the dark and in 50% relative humidity conditions. This result is quite better than the similar measurements for the doped spiro-OMeTAD-based devices.

Computational investigation of gas detection and selectivity on TiS3 nanoflakes supported by experimental evidence.

Titanium trisulfide (TiS3), a transition metal chalcogenide, bears the potential to replace silicon, when taking the form of nanoflakes, due to its favorable band gap and optical response. In this paper, we investigate the response of TiS3 nanoflakes to gas detection through a careful quantum computational approach and a few succinct measurements. The computations are benchmarked and compared with a relevant experiment at each step, where their results/conclusions are discussed. The most stable surface of TiS3 particles is determined as (001), in agreement with the literature. The adsorption of 5 gas molecules is characterized through formulating and estimating their adsorption intensity values, rather than using singled-out values of binding energies. This formulation, which is rooted in a statistical view of the gas adsorption process, distinguishes H2 and CH4 molecules from H2O and O2 explicitly and unambiguously through comparing their adsorption profiles. The difference in the adsorption intensities thus predicts and elucidates the difference in the sensing behaviour of TiS3 particles. This work suggests that the computationally obtained profile for the adsorption spectrum of gas molecules serves as a tool/criterion to predict the selectivity of their detection by TiS3.

Sensing behavior of flower-shaped MoS2 nanoflakes: case study with methanol and xylene.

Recent research interest in two-dimensional (2D) materials has led to an emerging new group of materials known as transition metal dichalcogenides (TMDs), which have significant electrical, optical, and transport properties. MoS2 is one of the well-known 2D materials in this group, which is a semiconductor with controllable band gap based on its structure. The hydrothermal process is known as one of the scalable methods to synthesize MoS2 nanostructures. In this study, the gas sensing properties of flower-shaped MoS2 nanoflakes, which were prepared from molybdenum trioxide (MoO3) by a facile hydrothermal method, have been studied. Material characterization was performed using X-ray diffraction, Brunauer-Emmett-Teller surface area measurements, elemental analysis using energy dispersive X-ray spectroscopy, and field-emission scanning electron microscopy. The gas sensing characteristics were evaluated under exposure to various concentrations of xylene and methanol vapors. The results reveal higher sensitivity and shorter response times for methanol at temperatures below 200 °C toward 200 to 400 ppm gas concentrations. The sensing mechanisms for both gases are discussed based on simulation results using density functional theory and charge transfer.

Graphene/cobalt nanocarrier for hyperthermia therapy and MRI diagnosis.

Graphene/cobalt nanocomposites are promising materials for theranostic nanomedicine applications, which are defined as the ability to diagnose, provide targeted therapy and monitor the response to the therapy. In this study, the composites were synthesized via chemical method, using graphene oxide as the source material and assembling cobalt nanoparticles of 15nm over the surface of graphene sheets. Various characterization techniques were then employed to reveal the morphology, size and structure of the nanocomposites, such as X-ray diffraction analysis, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, high resolution transmission electron microscopy and ultraviolet visible spectroscopy. Using ion-coupled plasma optical emission spectroscopy, cobalt concentration in the nanocomposites was found to be 80%. In addition, cytotoxicity of graphene/cobalt nanocomposites were evaluated using 3-[4,5-dimethylthiazol-2yl]-2,5-diphenyltetrazolium bromide or MTT assay. MTT viability assay exhibited biocompatibility to L929 mouse fibroblasts cells, under a high dose of 100µg/mL over 24h. Hyperthermia results showed the superior conversion of electromagnetic energy into heat at 350kHz frequency for 0.01 and 0.005g/L of the nanocomposites solution. The measured heat generation and energy transfer results were anticipated by the finite element analysis, conducted for the 3D structure. Magnetic resonance imaging characteristics also showed that negatively charge graphene/cobalt nanocomposites are suitable for T1-weighted imaging.

Voltammetric studies of Azathioprine on the surface of graphite electrode modified with graphene nanosheets decorated with Ag nanoparticles.

By using graphene nanosheets decorated with Ag nanoparticles (AgNPs-G) as an effective approach for the surface modification of pyrolytic graphite electrode (PGE), a sensing platform was fabricated for the sensitive voltammetric determination of Azathioprine (Aza). The prepared AgNPs-G nanosheets were characterized using transmission electron microscopy (TEM), X-ray diffraction (XRD), UV-vis and Raman spectroscopy techniques. The electrochemical behavior of Aza was investigated by means of cyclic voltammetry. Comparing to the bare PGE, a remarkable enhancement was observed in the response characteristics of Aza on the surface of the modified electrode (AgNPs-G/PGE) as well as a noticeable decrease in its reduction overpotential. These results can be attributed to the incredible enlargement in the microscopic surface area of the electrode due to the presence of graphene nanosheets together with strong adsorption of Aza on its surface. The effect of experimental parameters such as accumulation time, the amount of modifier suspension and pH of the supporting electrolyte were also optimized toward obtaining the maximum sensitivity. Under the optimum conditions, the calibration curve studies demonstrated that the peak current increased linearly with Aza concentrations in the range of 7 × 10(-7) to 1 × 10(-4)mol L(-1) with the detection limit of 68 nM. Further experiments revealed that the modified electrode can be successfully applied for the accurate determination of Aza in pharmaceutical preparations.

Fabrication of sensitive glutamate biosensor based on vertically aligned CNT nanoelectrode array and investigating the effect of CNTs density on the electrode performance.

In this report, the fabrication of vertically aligned carbon nanotube nanoelectrode array (VACNT-NEA) by photolithography method is presented. Electrochemical impedance spectroscopy as well as cyclic voltammetry was performed to characterize the arrays with respect to different diffusion regimes. The fabricated array illustrated sigmoidal cyclic voltammogram with steady state current dominated by radial diffusion. The fabricated VACNT-NEA and high density VACNTs were employed as electrochemical glutamate biosensors. Glutamate dehydrogenase is covalently attached to the tip of CNTs. The voltammetric biosensor, based on high density VACNTs, exhibits a sensitivity of 0.976 mA mM(-1) cm(-2) in the range of 0.1-20 µM and 0.182 mA mM(-1) cm(-2) in the range of 20-300 µM glutamate with a low detection limit of 57 nM. Using the fabricated VACNT-NEA, the sensitivity increases approximately to a value of 2.2 Am M(-1) cm(-2) in the range of 0.01 to 20 µM and to 0.1 A mM(-1) cm(-2) in the range of 20-300 µM glutamate. Using this electrode, a record of low detection limit of 10 nM was achieved for glutamate. The results prove the efficacy of the fabricated NEA for low cost and highly sensitive enzymatic biosensor with high sensitivity well suited for voltammetric detection of a wide range of clinically important biomarkers.

Investigation on the dynamics of electron transport and recombination in TiO2 nanotube/nanoparticle composite electrodes for dye-sensitized solar cells.

In this work, we report on fabrication and characterization of dye-sensitized solar cells based on TiO(2) nanotube/nanoparticle (NT/NP) composite electrodes. TiO(2) nanotubes were prepared by anodization of Ti foil in an organic electrolyte. The nanotubes were chemically separated from the foil, ground and added to a TiO(2) nanoparticle paste, from which composite NT/NP electrodes were fabricated. In the composite TiO(2) films the nanotubes existed in bundles with a length of a few micrometres. By optimizing the amount of NT in the paste, dye-sensitized solar cells with an efficiency of 5.6% were obtained, a 10% improvement in comparison to solar cells with pure NP electrodes. By increasing the fraction of NT in the electrode the current density increased by 20% (from 11.1 to 13.3 mA cm(-2)), but the open circuit voltage decreased from 0.78 to 0.73 V. Electron transport, lifetime and extraction studies were performed to investigate this behavior. A higher fraction of NT in the paste led to more and deeper traps in the resulting composite electrodes. Nevertheless, faster electron transport under short-circuit conditions was found with increased NT content, but the electron lifetime was not improved. The electron diffusion length calculated for short-circuit conditions was increased 3-fold in composite electrodes with an optimized NT fraction. The charge collection efficiency was more than 90% over a wide range of light intensities, leading to improved solar cell performance.

Comparison of trap-state distribution and carrier transport in nanotubular and nanoparticulate TiO(2) electrodes for dye-sensitized solar cells.

Dye-sensitized solar cells (DSCs) with nanotubular TiO(2) electrodes of varying thicknesses are compared to DSCs based on conventional nanoparticulate electrodes. Despite the higher degree of order in one-dimensional nanotubular electrodes, electron transport times and diffusion coefficients, determined under short-circuit conditions, are comparable to those of nanoparticulate electrodes. The quasi-Fermi level, however, is much lower in the nanotubes, suggesting a lower concentration of conduction band electrons. This provides evidence for a much higher diffusion coefficient for conduction band electrons in nanotubes than in nanoparticulate films. The electron lifetime and the diffusion length are significantly longer in nanotubular TiO(2) electrodes than in nanoparticulate films. Nanotubular electrodes have a trap distribution that differs significantly from nanoparticulate electrodes; they possess relatively deeper traps and have a characteristic energy of the exponential distribution that is more than two times that of nanoparticulate electrodes.