Direct Measurement of Near-Wall Molecular Transport Rate in a Microchannel and Its Dependence on Diffusivity.

Solute transport in a narrow space is the most elemental process in chromatography and biological pattern formation. However, the observation of such transport has been quite difficult, and theoretical investigations have therefore preponderated. Here, using a space- and time-resolved surface plasmon resonance (SPR) method, we measured the nanoscale near-wall (next to the wall) transport rate in a narrow channel after a solution and its solvent had come into contact. By combining the SPR method with a capillary injection method, which enables two solution plugs to flow immediately after they have made contact, we were able to measure the solute concentration evolution at the channel wall. We tested three combinations of two plugs of solution-water-glucose, sodium chloride-water, and glucose-sodium chloride-and succeeded in measuring diffusion-coefficient-dependent changes in the concentration of solute flowing through a rectangular microchannel in less than 0.4 s. A numerical analysis of this system revealed the acceleration of the solute/solution boundary moving on the wall and its deceleration at the center of the channel cross section. The observed experimental transport rate agreed with the numerical result quantitatively. These results show that the solute transport followed a laminar flow with a no-slip model and that the molecules were transported in the order of their diffusivity. In the third combination, when the two solutions made contact and started flowing, the interdiffusion of the solutes resulted in temporal concentrations lower than either of the solutions before contact, which indicated that the contact between the two solutions quickly led to separation by the advection-diffusion processes. We found that such a concentration profile could actually be measured. Our techniques are simple and applicable to a wide range of molecules; the method opens the way to direct observation of the space-time near-wall solute transport process and can be used for the rapid determination of diffusivity.

A reliable aptamer array prepared by repeating inkjet-spotting toward on-site measurement.

A preparation protocol is proposed for a reliable aptamer array utilizing an ink-jet spotter. We accumulated streptavidin and biotinylated-aptamer in this order on a biotinylated-polyethylene glycol-coated gold substrate to prepare an aptamer array. The aptamer array was prepared with an alternate spotting structure where each aptamer spot was placed between reference spots formed with blocking solution thus suppressing contamination from neighboring spots during the blocking and washing processes. Four aptamer spots were prepared in a small area of 1×4.8mm(2) with five reference spots made of blocking solution. We evaluated the thrombin binding ability of the spotted aptamer array using a multi-analysis surface plasmon resonance sensor. We prepared a disposable capillary-driven flow chip designed for on-site measurement (Miura et al., 2010) with our aptamer array and detected thrombin from phosphate-buffered saline at concentrations of 50ngmL(-1) and 1µgmL(-1) (equivalent to 1.35 and 27nM, respectively). A correlation was observed between the refractive index shift and thrombin concentration. This implies that our array preparation protocol meets the requirement for the preparation of a one-time-use chip for on-site measurement.

Floating chip mounting system driven by repulsive force of permanent magnets for multiple on-site SPR immunoassay measurements.

We have developed a measurement chip installation/removal mechanism for a surface plasmon resonance (SPR) immunoassay analysis instrument designed for frequent testing, which requires a rapid and easy technique for changing chips. The key components of the mechanism are refractive index matching gel coated on the rear of the SPR chip and a float that presses the chip down. The refractive index matching gel made it possible to optically couple the chip and the prism of the SPR instrument easily via elastic deformation with no air bubbles. The float has an autonomous attitude control function that keeps the chip parallel in relation to the SPR instrument by employing the repulsive force of permanent magnets between the float and a float guide located in the SPR instrument. This function is realized by balancing the upward elastic force of the gel and the downward force of the float, which experiences a leveling force from the float guide. This system makes it possible to start an SPR measurement immediately after chip installation and to remove the chip immediately after the measurement with a simple and easy method that does not require any fine adjustment. Our sensor chip, which we installed using this mounting system, successfully performed an immunoassay measurement on a model antigen (spiked human-IgG) in a model real sample (non-homogenized milk) that included many kinds of interfering foreign substances without any sample pre-treatment. The ease of the chip installation/removal operation and simple measurement procedure are suitable for frequent on-site agricultural, environmental and medical testing.

Passive fluidic chip composed of integrated vertical capillary tubes developed for on-site SPR immunoassay analysis targeting real samples.

We have successfully developed a surface plasmon resonance (SPR) measurement system for the on-site immunoassay of real samples. The system is composed of a portable SPR instrument (290 mm(W) × 160 mm(D) × 120 mm(H)) and a microfluidic immunoassay chip (16 mm(W) × 16 mm(D) × 4 mm(H)) that needs no external pump system. An integrated vertical capillary tube functions as a large volume (150 µL) passive pump and a waste reservoir that has sufficient capacity for several refill operations. An immunoassay was carried out that employed the direct injection of a buffer and a test sample in sequence into a microfluidic chip that included 9 antibody bands and 10 reference reagent bands immobilized in the flow channel. By subtracting a reliable averaged reference sensorgram from the antibody, we effectively reduced the influence of the non-specific binding, and then our chip successfully detected the specific binding of spiked IgG in non-homogeneous milk. IgG is a model antigen that is certain not to be present in non-homogeneous milk, and non-homogeneous milk is a model of real sample that includes many interfering foreign substances that induce non-specific binding. The direct injection of a real sample with no pretreatment enabled us to complete the entire immunoassay in several minutes. This ease of operation and short measuring time are acceptable for on-site agricultural, environmental and medical testing.

Newly developed chemical probes and nano-devices for cellular analysis.

A cellular analyzing system including a "real-time cellular imaging system" and a "comprehensive analyzing system for cellular responses" was developed. A "real-time cellular imaging system" is a system used to measure real-time imaging of multiple phenomena of a single cell with high special and temporal resolutions for the purpose to understand the pathology and physiology in a single cell and realize to single cell level diagnosis. A "real-time cellular imaging system" includes multi-probe imaging with AFM (atomic force microscopy), optical and SECM (scanning electrochemical microscopy) modes, which provides us with topological information and biochemical reactions at the local area of the interior and exterior of a cell. Scanning electrochemical/optical microscopy was applied to image PC12 cells. On the other hand, cells respond to their specific substances via their ligands. Therefore, the comprehensive analysis of protein-protein interaction is the important issue to determine the functions of cells. For this purpose, a "comprehensive analysis system for cellular responses" was developed. This system is based on SPR (surface plasmon resonance) and MS (mass spectrometry) using a nano-fabricated substrate. The interaction between IL-1 beta and anti-IL-1 beta antibodies was detected.

Heavy phosphate adsorption on amorphous ITO film electrodes: nano-barrier effect for highly selective exclusion of anionic species.

We prepared an amorphous indium tin oxide (ITO) film and studied it with respect to its surface characterization and the effect of phosphate adsorption on its electrochemical properties. The film was deposited using RF sputtering under ambient low-oxygen conditions at room temperature. The XPS results revealed that the amount of phosphate adsorbed on the amorphous ITO film was more than 4.6 times greater than that adsorbed on commercially available polycrystalline ITO film in spite of the smaller microscopic surface area of the former. Electrochemical responses for anionic species such as L-ascorbic acid (AA) and 3,4-dihydroxyphenylacetic acid (DOPAC) on the phosphate-adsorbed ITO film electrodes were more effectively suppressed at the amorphous ITO film electrode than at the polycrystalline ITO film electrode when a phosphate-containing electrolyte was used. Such suppression could be attributed to the electrostatic repulsion between the anionic species and more heavily adsorbed phosphate on our amorphous ITO film electrode surface. This effect is made more pronounced by increasing the phosphate concentration to 1 mM. With 1 mM phosphate, the amorphous ITO film electrode showed the highest selectivity for dopamine (DA) against the anionic species, namely, 880 for DA/AA and 330 for DA/DOPAC, respectively. In contrast, the selectivity was 120 for DA/AA and 20 for DA/DOPAC with the polycrystalline ITO film electrode.

Selective detection of a catecholamine against electroactive interferents using an interdigitated heteroarray electrode consisting of a metal oxide electrode and a metal band electrode.

We developed an interdigitated array electrode (IDAE) consisting of a metal oxide electrode and a metal band heteroelectrode and employed it for the selective detection of catecholamines. We used an indium-tin oxide (ITO) film as the oxidation electrode of the IDAE because the ITO was able to suppress response currents from L-ascorbic acid (AA) and uric acid (UA), which are major electroactive interferents in biological fluids. However, the ITO film also suppresses the reduction of quinones including oxidized catecholamines. We developed a simple technique for fabricating our hetero IDAE, which also preserves the electrochemical properties of the ITO. When we compared hetero ITO-gold, homo ITO-ITO, and carbon-carbon IDAEs, we found that the hetero IDAE provided both high sensitivity and selectivity for DA detection. We achieved high selectivities for DA against AA and UA. The ratios of the response currents of AA and UA to DA were calculated as 6 and 5%, respectively.

Discriminative detection of volatile sulfur compound mixtures with a plasma-polymerized film-based sensor array installed in a humidity-control system.

We demonstrated the discrimination of volatile sulfur compound mixtures with different mixing ratios by using an array of the plasma-polymerized film (PPF)-coated quartz crystal resonators. The PPF sensor array, which contains PPFs prepared from amino acids and synthetic polymers, exhibited different response patterns to mono or mixed volatile sulfur compounds (VSCs) (hydrogen sulfide and methanethiol) under a dry environment. The sensor array was installed in a desktop-size relative humidity controller. The relative humidity and temperature conditions of the sample flow to the sensor cell were equalized to those of the inner atmosphere of the sensor cell based on the concept of the two-separate-temperatures method. In this way, the baseline drift of PPF sensor response caused by the introduction of a highly humid sample was successfully suppressed. We compared the sensor array responses under the controlled humidity conditions. Presorption of water molecules by PPFs caused a decrease of sensor sensitivity, but the films still had the ability to discriminate sub-ppmv VSC mixtures having 6:1, 1:1, and 1:6 mixture ratios of hydrogen sulfide and methanethiol.

Biocompatible glucose sensor prepared by modifying protein and vinylferrocene monomer composite membrane.

This paper proposes a very simple procedure for preparing a biocompatible sensor based on a protein (bovine serum albumin, BSA), enzyme and vinylferrocene (VF) composite membrane modified electrode. The membrane was prepared simply by first casting vinylferrocene and then coating it with BSA and glucose oxidase immobilised with glutaraldehyde. The sensor response was independent of dissolved oxygen concentration from 3 to 10 ppm and showed good stability for serum sample measurement, unlike the commonly used BSA/enzyme modified electrode. The sensor response was almost unchanged over the measurement time (>10 h) whereas the responses of a BSA and glucose oxidase modified platinum electrode and an osmium-polyvinylpyridine wired horseradish peroxidase modified electrode (Ohara et al., 1993) fell to 68% of their initial value in a serum sample containing 10mM glucose.

Application of an absorption-based surface plasmon resonance principle to the development of SPR ammonium ion and enzyme sensors.

Two new types of surface plasmon resonance (SPR) sensors that can determine the concentration of ammonium cations and urea were realized based on the previously reported theory of the absorption-based SPR measurement method. The change of the dielectric constant caused by the change of the light absorption characteristics of dyes incorporated in a sensing membrane phase is utilized in these SPR sensors. The determination of ions using the SPR sensor was realized by detecting the SPR signals of the minimum reflectance related to the change of absorption spectra of the dye in the ion optode membrane consisting of an ammonium-selective ionophore (TD19C6) and a lipophilic cationic dye (KD-M11) that shows absorption spectral changes due to protonation and deprotonation. A SPR enzyme sensor that can determine the concentration of urea was prepared by the combination of this ion optode membrane and an enzyme membrane based on urease. With the newly developed SPR sensors, the intensity changes of the reflectance at the fixed SPR resonance angle are monitored, which is different from conventional SPR sensors where usually the change of the SPR resonance angles is detected. In a continuous-flow experiment using the SPR ion sensor for NH4+ ion determination, a dynamic measurement range from 10(-5) to 10(-2) M was achieved. In the case of the enzyme-based SPR urea sensor, a dynamic range from 10(-4) to 10(-1) M was observed in a stopped-flow batch arrangement. It is expected that this sensing technique can be applied for the SPR-based detection of a wide range of low molecular weight analytes.

Imaging of electrochemical enzyme sensor on gold electrode using surface plasmon resonance.

Three types of imaging, namely layer structure, electrochemical reaction, and enzyme sensor response, were achieved by applying surface plasmon resonance (SPR) measurement to an electrochemical biosensor. We constructed glucose oxidase based mediator type sensors on a gold electrode by spotting the mediator that contained horseradish peroxidase and spin coating the glucose oxidase film. The layer structure of the sensor was imaged by means of angle scanning SPR measurement. The single sensor spot (about 1 mm in diameter) consisted of about 100 x 100 pixels and its spatial structure was imaged. The multilayer structure of the enzyme sensor had a complex reflectance-incident angle curve and this required us to choose a suitable incident angle for mapping the redox state. We chose an incident angle that provided the most significant reflection intensity difference by using data obtained from two angle scanning SPR measurements at different electrode potentials. At this incident angle, we controlled the electrochemical states of the spotted mediator in cyclic voltammetry and imaged the degree to which the charged site density changed. Finally, we mapped the enzymatic activity around the mediator spot by the enzymatic reoxidation of pre-reduced mediator in the presence of glucose.

Preparation of refractive index matching polymer film alternative to oil for use in a portable surface-plasmon resonance phenomenon-based chemical sensor method.

In order to simplify the procedure for assembling a surface-plasmon resonance (SPR) sensor, a refractive index matching polymer film was prepared as an alternative to the conventionally used matching oil. The refractive index matching polymer film, the refractive index of which was nearly equal to the prism and sensor chip material (a cover glass) of the SPR sensor, was prepared by casting a tetrahydrofuran solution of poly (vinyl chloride) (PVC) containing equal weights of dioctyl phthalate and tricresyl phosphate. The refractive index matching polymer film was found to have a refractive index of 1.516, which is identical to that of the prism and the cover glass used for the present SPR sensor. The utility of the matching polymer film for the SPR sensor was confirmed by the detection of anti-human albumin, based on an antigen-antibody reaction.