Polymer Injectivity Test Design Using Numerical Simulation.

Polymer flooding is an enhanced oil recovery (EOR) process, which has received increasing interest in the industry. In this process, water-soluble polymers are used to increase injected water viscosity in order to improve mobility ratio and hence improve reservoir sweep. Polymer solutions are non-Newtonian fluids, i.e., their viscosities are shear dependent. Polymers may exhibit an increase in viscosity at high shear rates in porous media, which can cause injectivity loss. In contrast, at low shear rates they may observe viscosity loss and hence enhance the injectivity. Therefore, due to the complex non-Newtonian rheology of polymers, it is necessary to optimize the design of polymer injectivity tests in order to improve our understanding of the rheology behavior and enhance the design of polymer flood projects. This study has been addressing what information that can be gained from polymer injectivity tests, and how to design the test for maximizing information. The main source of information in the field is from the injection bottom-hole pressure (BHP). Simulation studies have analyzed the response of different non-Newtonian rheology on BHP with variations of rate and time. The results have shown that BHP from injectivity tests can be used to detect in-situ polymer rheology.

Qualification of New Methods for Measuring In Situ Rheology of Non-Newtonian Fluids in Porous Media.

Pressure drop (P) versus volumetric injection rate (Q) data from linear core floods have typically been used to measure in situ rheology of non-Newtonian fluids in porous media. However, linear flow is characterized by steady-state conditions, in contrast to radial flow where both pressure and shear-forces have non-linear gradients. In this paper, we qualify recently developed methods for measuring in situ rheology in radial flow experiments, and then quantitatively investigate the robustness of these methods against pressure measurement error. Application of the new methods to experimental data also enabled accurate investigation of memory and rate effects during polymer flow through porous media. A radial polymer flow experiment using partially hydrolyzed polyacrylamide (HPAM) was performed on a Bentheimer sandstone disc where pressure ports distributed between a central injector and the perimeter production line enabled a detailed analysis of pressure variation with radial distance. It has been suggested that the observed shear-thinning behavior of HPAM solutions at low flux in porous media could be an experimental artifact due to the use of insufficiently accurate pressure transducers. Consequently, a generic simulation study was conducted where the level of pressure measurement error on in situ polymer rheology was quantitatively investigated. Results clearly demonstrate the robustness of the history match methods to pressure measurement error typical for radial flow experiments, where negligible deviations from the reference rheology was observed. It was not until the error level was increased to five-fold of typical conditions that significant deviation from the reference rheology emerged. Based on results from pore network modelling, Chauveteau (1981) demonstrated that polymer flow in porous media may at some rate be influenced by the prior history. In this paper, polymer memory effects could be evaluated at the Darcy scale by history matching the pressure drop between individual pressure ports and the producer as a function of injection rate (conventional method). Since the number of successive contraction events increases with radial distance, the polymer has a different pre-history at the various pressure ports. Rheology curves obtained from history matching the radial flow experiment were overlapping, which shows that there is no influence of geometry on in-situ rheology for the particular HPAM polymer investigated. In addition, the onset of shear-thickening was independent of volumetric injection rate in radial flow.

The prognosis of impaired left ventricular systolic function and heart failure in a middle-aged and elderly population in an urban population segment of Copenhagen.

AIMS: To determine the prognosis, total mortality and cardiac morbidity, of patients with left ventricular systolic dysfunction and heart failure (HF) in a general population sample. METHODS AND RESULTS: A total of 764 subjects, 432 females and 332 males, median age (range) 66 years (50-89), participated in this cross sectional survey. The study population was recruited from randomly selected general practitioners and stratified to include a minimum of 150 persons in each age decade stratum. Each participant filled in a heart failure questionnaire and ECG, blood tests and echocardiography were performed. Median (range) follow-up was 1145 (51-1197) days. Subjects with LVEF < or = 0.40 had a significantly higher all-cause mortality (27.8% vs. 5.6%, P<0.0001), admission rate for HF (25.0% vs. 1.9%, P<0.0001) and for other cardiac causes (25.0% vs. 6.3%, P<0.0001) than in subjects with LVEF>0.40. The age and gender adjusted 2-year relative risk of death was 4.6 (95% C.I.=1.6-13.2). No significant difference in mortality was found between subjects with or without heart failure symptoms. CONCLUSION: Significantly higher mortality as well as cardiac morbidity was found in subjects with symptomatic and asymptomatic LV systolic dysfunction compared to those with normal systolic function. These conditions were among the strongest predictors of all-cause mortality and cardiac morbidity.