ABSTRACT
OBJECTIVES: Sintering influences the optical properties of zirconia. This study examined the effect of altering sintering temperature and time of monochrome (Mo) and multilayer (Mu) 5 mol% yttria-partially stabilized zirconia (5Y-PSZ) on color characteristics. MATERIALS AND METHODS: Three hundred specimens (width × length × thickness = 10 × 20 × 2 mm) were prepared from Mo and Mu (with cervical [C], middle [M], and incisal [I] region) 5Y-PSZ and randomly sintered at decreasing (Td: 1,450°C), regular (Tr: 1,500°C), and increasing (TI: 1,550°C) sintering temperature, with extremely short (He: 10 minutes), ultrashort (Hu: 15 minutes), short (Hs: 30 minutes), and regular (Hr: 135 minutes) sintering time (n = 15/group). Color appearance (EW ), translucency parameter (TP), contrast ratio (CR), opalescence parameter (OP), and color appearance difference (∆E diff) were evaluated in the CIE L*a*b* system. Microstructures were evaluated by scanning electron microscope (SEM) and X-ray diffractometer (XRD). STATISTICAL ANALYSIS: Analysis of variance (ANOVA) and Bonferroni comparisons were determined for significant differences (p < 0.05). RESULTS: Significant differences in color parameters upon zirconia type, sintering temperature, and sintering time, and their interactions were indicated (p < 0.05). Increasing sintering temperature and extended sintered time resulted in larger grain, reduced tetragonal-to-monoclinic phase transformation, and significantly increased the TP and OP, but decreased the CR and ∆E diff (p < 0.05). Decreasing sintering temperature and time led to clinically unacceptable color appearance. CONCLUSION: Mo was found to be more translucent than Mu. To achieve the most favorable optical properties, increasing sintering temperature and extending sintering time are recommended. Decreasing sintering temperature is not suggested. However, shortened sintering time is feasible, but it needs sintering with increasing sintering temperature to achieve a promising color appearance.
ABSTRACT
OBJECTIVES: Sintering parameters influence the properties of zirconia. This study examined the effect of altering sintering temperature and time of monochrome and multilayer 5 mol% yttria-partially stabilized zirconia (5Y-PSZ) on flexural strength. MATERIALS AND METHODS: Three hundred specimens (width × length × thickness = 10 × 20 × 2 mm) were prepared from monolayer (ZX) and multilayer (ZM) 5Y-PSZ and randomly sintered at decreasing (TD: 1,450°C), regular (TR: 1,500°C), and increasing (TI: 1,550°C) sintering temperature, with extremely short (HE: 10 minutes), ultrashort (HU: 15 minutes), short (HS: 30 minutes), and regular (HR: 135 minutes) sintering time (n = 15/group). The precrack was induced on the tension side before testing for flexural strength (σ). STATISTICAL ANALYSIS: Analysis of variance and Tukey's test were used for significant differences of σ at p < 0.05. The microstructure and crystalline (monoclinic; m, tetragonal; t, cubic; c) phase were evaluated by scanning electron microscope (SEM) and X-ray diffractometer (XRD). RESULTS: ZXTIHS indicated the highest σ for ZX (315.81 ± 18.91 MPa), whereas ZMTIHS indicated the highest σ for ZM (335.21 ± 36.18 MPa). There was no significant difference for σ between ZX and ZM (p > 0.05). Sintering zirconia at TI or HR indicated significantly higher σ than sintering at TD or TR or with HS, HE, or HU for both ZX and ZM (p < 0.05). There was no significant difference for σ between TRHR and TIHS, TIHU, and TIHE (p > 0.05). SEM indicated intergranular and transgranular fractures. XRD revealed predominately c- and t-phases and minor amounts of m-phase. CONCLUSION: Increasing sintered temperature with decreasing time offers acceptable strength to regular sintering. Raising sintering temperature with decreasing time is suggested to facilitate chairside restorative reconstruction.
