Broadband terahertz guided-mode resonance filter using cyclic olefin copolymer.

We propose an all-dielectric single-layer guided-mode resonance filter (GMRF) operating in the high-frequency terahertz (THz) region. For the fabrication of thin gratings to achieve strong resonance in the high-frequency region, the refractive index and absorption must be small, while the tensile strength must be high. Cyclic olefin copolymer (COC) films have a lower refractive index and absorption than polyethylene terephthalate (PET) films and a higher tensile yield strength than polytetrafluoroethylene (PTFE) films. Therefore, the COC film was found suitable to fabricate a GMRF operating in the high-frequency THz region. We fabricated COC-based single-layer GMRFs with a thickness of 50 µm and grating periods of 500, 400, 300, 200, and 100 µm; the resonance frequencies of the TE0,1 mode were 0.576, 0.712, 0.939, 1.329, and 2.759 THz, respectively. A shorter grating period caused a greater shift of the resonance to a higher frequency. In particular, the COC film enabled the fabrication of a 100-µm grating period with a ridge width of 32 µm and length of 2 mm, enabling the GMRF to operate up to 2.759 THz, which is very high frequency compared to the previous highest frequency of 0.7 THz. These results were in good agreement with a simulation using rigorous coupled-wave analysis.

Polarization-independent all-dielectric guided-mode resonance filter according to binary grating and slab waveguide dimensions.

All-dielectric binary gratings, with and without slab waveguides, are designed to generate polarization-independent guided-mode resonance filters (GMRFs) operating in the THz frequency region using the rigorous coupled-wave analysis (RCWA) method. The filling factor and thickness of the grating were adjusted to have equal resonance frequencies of transverse electric (TE)- and transverse magnetic (TM)-polarized THz beams. The single polarization-independent resonance for a binary grating without a slab waveguide was obtained at 0.459 THz with full width at half maximum (FWHM) values of 8.3 and 8.5 GHz for the TE and TM modes, respectively. Moreover, double-layered polarization-independent resonances for binary gratings with slab waveguides were obtained at 0.369 and 0.442 THz with very high Q-factors of up to 284. This is the first study to propose a polarization-independent GMRF with two resonant frequencies.

Real-time ultrafast oscilloscope with a relativistic electron bunch train.

The deflection of charged particles is an intuitive way to visualize an electromagnetic oscillation of coherent light. Here, we present a real-time ultrafast oscilloscope for time-frozen visualization of a terahertz (THz) optical wave by probing light-driven motion of relativistic electrons. We found the unique condition of subwavelength metal slit waveguide for preserving the distortion-free optical waveform during its propagation. Momentary stamping of the wave, transversely travelling inside a metal slit, on an ultrashort wide electron bunch enables the single-shot recording of an ultrafast optical waveform. As a proof-of-concept experiment, we successfully demonstrated to capture the entire field oscillation of a THz pulse with a sampling rate of 75.7 TS/s. Owing to the use of transversely-wide and longitudinally-short electron bunch and transversely travelling wave, the proposed "single-shot oscilloscope" will open up new avenue for developing the real-time petahertz (PHz) metrology.

THz guided-mode resonance notch filter with variable filtering strength.

In this paper, we propose a terahertz (THz) guided-mode resonance (GMR) notch filter made of a monolithic polyethylene terephthalate (PET) film, which has a monolayer grating structure. The proposed configuration shows both polarization-dependent and polarization-independent notch filter characteristics for the incident THz wave depending on the rotation angle of the second grating film. When the rotation angle is 0°, the filtering strength (transmittance) at resonance frequency changes from 0.4 (0.996) to 99.0% (0.010) according to the incident polarization. The transmittance continuously decreases with increasing rotation angle until 90°. When the rotation angle is 90°, the transmittance converges to 0.065 (± 0.015) independent of the incident wave polarization. When the incident polarization angle ranges from 90° to 180°, paradoxically, the transmittance through the two GMR grating films is greater than the transmittance through only the first GMR grating film due to the enhancement of the vertical component of the THz wave. These results agree well with a calculation using a polar coordinate system.

Method for developing a sub-10 fs ultrafast electron diffraction technology.

The experimental observation of femtosecond dynamics in atoms and molecules by stroboscopic technologies utilizing x ray or electron flashes has attracted much attention and has rapidly developed. We propose a feasible ultrafast electron diffraction (UED) technology with high brightness and a sub-10 fs temporal resolution. We previously demonstrated a UED system with an overall temporal resolution of 31 fs by using an RF photoelectron gun and a 90° achromatic bending structure. This UED structure enabled a bunch duration of 25 fs and a low timing jitter of less than 10 fs while maintaining a high bunch charge of 0.6 pC. In this paper, we demonstrate a simple way to further compress the electron bunch duration to sub-10 fs based on installing an energy filter in the dispersion section of the achromatic bend. The energy filter removes the electrons belonging to nonlinear parts of the phase space. Through numerical simulations, we demonstrate that the electron bunches can be compressed, at the sample position, to a 6.2 fs (rms) duration for a 100 fC charge. This result suggests that the energy filtering approach is more viable and effective than complicated beam-shaping techniques that commonly handle the nonlinear distribution of the electron beam. Furthermore, a gas-filled hollow core fiber compressor and a Ti:sapphire amplifier are used to implement pump laser pulses of less than 5 fs (rms). Thus, we could present the full simulation results of a sub-10 fs UED, and we believe that it will be one of the technical prototypes to challenge the sub-fs time resolution.

Comparative study of Yb:KYW planar waveguide lasers Q-switched by direct- and evanescent-field interaction with carbon nanotubes.

Both direct- and evanescent-field interactions with carbon nanotubes (CNTs) are applied to achieve stable Q-switched operation of Yb:KYW planar waveguide lasers. The performance characteristics were investigated in a same cavity configuration and analyzed in detail in the following three cases, CNTs deposited onto end mirror (M-coating), output coupler (OC-coating) and top surface of the planar waveguide (WG-coating). Maximum output powers, repetition rates, and minimum pulse durations are 61 mW, 1103 kHz and 215 ns for OC-coating, 39 mW, 1052 kHz and 275 ns for WG-coating, and 26 mW, 1119 kHz and 217 ns for M-coating, respectively. From the calculation of the configuration-dependent stability range, the beam size and the electric field distribution in the Yb:KYW planar waveguide, it is confirmed that the evanescent-field interaction scheme makes stable Q-switching possible with much lower intensities at saturable absorber compared to the direct-field interaction scheme in the presented waveguide laser operation.

THz-pump and X-ray-probe sources based on an electron linac.

We describe a compact THz-pump and X-ray-probe beamline, based on an electron linac, for ultrafast time-resolved diffraction applications. Two high-energy electron (γ > 50) bunches, 5 ns apart, impinge upon a single-foil or multifoil radiator and generate THz radiation and X-rays simultaneously. The THz pulse from the first bunch is synchronized to the X-ray beam of the second bunch by using an adjustable optical delay of a THz pulse. The peak power of THz radiation from the multifoil radiator is estimated to be 0.14 GW for a 200 pC well-optimized electron bunch. GEANT4 simulations show that a carbon foil with a thickness of 0.5-1.0 mm has the highest yield of 10-20 keV hard X-rays for a 25 MeV beam, which is approximately 103 photons/(keV pC-electrons) within a few degrees of the polar angle. A carbon multifoil radiator with 35 foils (25 µm thick each) can generate close to 103 hard X-rays/(keV pC-electrons) within a 2° acceptance angle. With 200 pC charge and a 100 Hz repetition rate, we can generate 107 X-rays per 1 keV energy bin per second or 105 X-rays per 1 keV energy bin per pulse. The longitudinal time profile of an X-ray pulse ranges from 400 to 600 fs depending on the acceptance angle. The broadening of the time duration of an X-ray pulse is observed owing to its diverging effect. A double-crystal monochromator will be used to select and transport the desired X-rays to the sample. The heating of the radiators by an electron beam is negligible because of the low beam current.

10-fs-level synchronization of photocathode laser with RF-oscillator for ultrafast electron and X-ray sources.

Ultrafast electron-based coherent radiation sources, such as free-electron lasers (FELs), ultrafast electron diffraction (UED) and Thomson-scattering sources, are becoming more important sources in today's ultrafast science. Photocathode laser is an indispensable common subsystem in these sources that generates ultrafast electron pulses. To fully exploit the potentials of these sources, especially for pump-probe experiments, it is important to achieve high-precision synchronization between the photocathode laser and radio-frequency (RF) sources that manipulate electron pulses. So far, most of precision laser-RF synchronization has been achieved by using specially designed low-noise Er-fibre lasers at telecommunication wavelength. Here we show a modular method that achieves long-term (>1 day) stable 10-fs-level synchronization between a commercial 79.33-MHz Ti:sapphire laser oscillator and an S-band (2.856-GHz) RF oscillator. This is an important first step toward a photocathode laser-based femtosecond RF timing and synchronization system that is suitable for various small- to mid-scale ultrafast X-ray and electron sources.

Highly nonlinear organic crystal OHQ-T for efficient ultra-broadband terahertz wave generation beyond 10 THz.

We report on efficient generation of ultra-broadband terahertz (THz) waves via optical rectification in a novel nonlinear organic crystal with acentric core structure, i.e. 2-(4-hydroxystyryl)-1-methylquinolinium 4-methylbenzenesulfonate (OHQ-T), which possesses an ideal molecular structure leading to a maximized nonlinear optical response for near-infrared-pumped THz wave generation. By systematic studies on wavelength-dependent phase-matching conditions in OHQ-T crystals of different thicknesses we are able to generate coherent THz waves with a high peak-to-peak electric field amplitude of up to 650 kV/cm and an upper cut-off frequency beyond 10 THz. High optical-to-THz conversion efficiency of 0.31% is achieved by efficient index matching with a selective pumping at 1300 nm.

In vivo analysis of THz wave irradiation induced acute inflammatory response in skin by laser-scanning confocal microscopy.

The recent development of THz sources in a wide range of THz frequencies and power levels has led to greatly increased interest in potential biomedical applications such as cancer and burn wound diagnosis. However, despite its importance in realizing THz wave based applications, our knowledge of how THz wave irradiation can affect a live tissue at the cellular level is very limited. In this study, an acute inflammatory response caused by pulsed THz wave irradiation on the skin of a live mouse was analyzed at the cellular level using intravital laser-scanning confocal microscopy. Pulsed THz wave (2.7 THz, 4 µs pulsewidth, 61.4 µJ per pulse, 3Hz repetition), generated using compact FEL, was used to irradiate an anesthetized mouse's ear skin with an average power of 260 mW/cm(2) for 30 minutes using a high-precision focused THz wave irradiation setup. In contrast to in vitro analysis using cultured cells at similar power levels of CW THz wave irradiation, no temperature change at the surface of the ear skin was observed when skin was examined with an IR camera. To monitor any potential inflammatory response, resident neutrophils in the same area of ear skin were repeatedly visualized before and after THz wave irradiation using a custom-built laser-scanning confocal microscopy system optimized for in vivo visualization. While non-irradiated control skin area showed no changes in the number of resident neutrophils, a massive recruitment of newly infiltrated neutrophils was observed in the THz wave irradiated skin area after 6 hours, which suggests an induction of acute inflammatory response by the pulsed THz wave irradiation on the skin via a non-thermal process.

Generating high-power short terahertz electromagnetic pulses with a multifoil radiator.

We describe a multifoil cone radiator capable of generating high-field short terahertz pulses using short electron bunches. Round flat conducting foil plates with successively decreasing radii are stacked, forming a truncated cone with the z axis. The gaps between the foil plates are equal and filled with some dielectric (or vacuum). A short relativistic electron bunch propagates along the z axis. At sufficiently high particle energy, the energy losses and multiple scattering do not change the bunch shape significantly. When passing by each gap between the foil plates, the electron bunch emits some energy into the gap. Then, the radiation pulses propagate radially outward. For transverse electromagnetic waves with a longitudinal (along the z axis) electric field and an azimuthal magnetic field, there is no dispersion in these radial lines; therefore, the radiation pulses conserve their shapes (time dependence). At the outer surface of the cone, we have synchronous circular radiators. Their radiation field forms a conical wave. Ultrashort terahertz pulses with gigawatt-level peak power can be generated with this device.

Simple method for the temporal characterization of amplified spontaneous emission in femtosecond terawatt Ti:sapphire lasers.

We have analyzed the temporal characteristics of amplified spontaneous emission (ASE) in femtosecond terawatt Ti:sapphire lasers by using a simple method based on fast photodiodes. Instead of measuring ASE directly with fast photodiodes, we created a narrow gap in the spectrum of seed pulses and, after amplification, detected the pure ASE signal through the gap by using a fast photodiode covered with a bandpass filter with high transmission at the gap. Because the detected ASE signal was completely separated from amplified main pulses, preceding and even trailing ASEs could be characterized quantitatively in a single-shot measurement. We believe that our method is a good alternative or a complement to conventional methods for ASE measurements.

A compact low-energy electron beam irradiator.

A new compact low-energy electron beam irradiator has been developed. The irradiator generates an electron beam to the air with energy variable from 35 to 80 keV and with a maximum current of 1 mA. The irradiation area is 30 x 30 mm2. A special irradiation port is developed for this low-energy irradiator. The electron beam is generated from a thermionic LaB6 cathode in vacuum. The beam is extracted to the air through a havar foil window. The thickness of the window is 4.8 microm, it is vacuum-tightly connected to the window to support by an indium wire. A controlled bow geometry of the window helps the thin window withstand the vacuum pressure. Cold air generated from a vortex tube cools down both the window and its support in order to prevent the window from melting down, due to beam energy dissipated in the foil. We found that about 60% of the beam current is extracted to the air at 80 keV.