Antisolvent fabrication of monodisperse liposomes using novel ultrasonic microreactors: Process optimization, performance comparison and intensification effect.

Liposomes as drug carriers for the delivery of therapeutic agents have triggered extensive research but it remains a grand challenge to develop a novel technology for enabling rapid and mass fabrication of monodisperse liposomes. In this work, we constructed a novel ultrasonic microfluidic technology, namely ultrasonic microreactor (USMR) with two different conjunction structure (co-flow and impinge flow, corresponding to USMR-CF and USMR-IF, respectively), to prepare uniform liposomes by antisolvent precipitation method. In this process, the monodisperse liposomes with tunable droplet sizes (DS) in 60-100 nm and a polydispersity index (PDI) less than 0.1 can easily be achieved by tuning the total flow rate, flow rate ratio, ultrasonic power, and lipid concentration within the two USMRs. Impressively, the USMR-IF is superior for reducing the PDI and tuning DS of the liposomes over the USMR-CF. More importantly, the ultrasonic can effectively reduce DS and PDI at the low TFR and support the IF-micromixer in reducing the PDI even at a high TFR. These remarkable performances are mainly due to the rapid active mixing, fouling-free property and high operation stability for USMR-IF. In addition, diverse lipid formulations can also be uniformly assembled into small liposomes with narrow distribution, such as the prepared HSPC-based liposome with DS of 59.6 nm and PDI of 0.08. The liposomes show a high stability and the yield can reach a high throughput with 108 g/h by using the USMR-IF at an initial lipid concentration of 60 mM. The results in the present work highlight a novel ultrasonic microfluidic technology in the preparation of liposomes and may pave an avenue for the rapid, fouling-free, and high throughput fabrication of different and monodisperse nanomedicines with controllable sizes and narrow distribution.

Isolation of Chalcomoracin as a Potential α-Glycosidase Inhibitor from Mulberry Leaves and Its Binding Mechanism.

Diabetes is a chronic metabolic disease, whereas α-glucosidases are key enzymes involved in the metabolism of starch and glycogen. There is a long history of the use of mulberry leaf (the leaf of Morus alba) as an antidiabetic herb in China, and we found that chalcomoracin, one of the specific Diels-Alder adducts in mulberry leaf, had prominent α-glucosidase inhibitory activity and has the potential to be a substitute for current hypoglycemic drugs such as acarbose, which have severe gastrointestinal side effects. In this study, chalcomoracin was effectively isolated from mulberry leaves, and its α-glucosidase inhibition was studied via enzymatic kinetics, isothermal titration (ITC) and molecular docking. The results showed that chalcomoracin inhibited α-glucosidase through both competitive and non-competitive manners, and its inhibitory activity was stronger than that of 1-doxymycin (1-DNJ) but slightly weaker than that of acarbose. ITC analysis revealed that the combination of chalcomoracin and α-glucosidase was an entropy-driven spontaneous reaction, and the molecular docking results also verified this conclusion. During the binding process, chalcomoracin went into the "pocket" of α-glucosidase via hydrophobic interactions, and it is linked with residues Val544, Asp95, Ala93, Gly119, Arg275 and Pro287 by hydrogen bonds. This study provided a potential compound for the prevention and treatment of diabetes and a theoretical basis for the discovery of novel candidates for α-glycosidase inhibitors.

Long-Term Antibacterial Film Nanocomposite Incorporated with Patchouli Essential Oil Prepared by Supercritical CO2 Cyclic Impregnation for Wound Dressing.

Biocompatible skin wound dressing materials with long-term therapeutic windows and anti-infection properties have attracted great attention all over the world. The cooperation between essential oil and non-toxic or bio-based polymers was a promising strategy. However, the inherent volatility and chemical instability of most ingredients in essential oils make the sustained pharmacological activity of essential oil-based biomaterials a challenge. In this study, a kind of film nanocomposite loaded with patchouli essential oil (PEO-FNC) was fabricated. PEO-loaded mesoporous silica nanoparticles (PEO-MSNs) with drug load higher than 40 wt% were firstly prepared using supercritical CO2 cyclic impregnation (SCCI), and then combined with the film matrix consisting of polyvinyl alcohol and chitosan. The morphology of PEO-MSNs and PEO-FNC was observed by transmission and scanning electron microscope. The mechanical properties, including hygroscopicity, tensile strength and elongation at break (%), were tested. The release behavior of PEO from the film nanocomposite showed that PEO could keep releasing for more than five days. PEO-FNC exhibited good long-term (>48 h) antibacterial effect on Staphylococcus aureus and non-toxicity on mouse fibroblast (L929 cells), making it a promising wound dressing material.

Zein/MCM-41 Nanocomposite Film Incorporated with Cinnamon Essential Oil Loaded by Modified Supercritical CO2 Impregnation for Long-Term Antibacterial Packaging.

Antimicrobial medicine and food packages based on bio-based film containing essential oils have attracted great attention worldwide. However, the controlled release of essential oils from these film nanocomposites is still a big challenge. In this study, a long-term antibacterial film nanocomposite composed of zein film and cinnamon essential oil (CEO) loaded MCM-41 silica nanoparticles was prepared. The CEO was loaded into MCM-41 particles via modified supercritical impregnation efficiently with a high drug load (>40 wt%). The morphologies of the prepared nanoparticles and film nanocomposite were characterized by a scanning electron microscope. The release behaviors of CEO under different temperatures, high humidity, continuous illumination and in phosphate buffer solution (PBS) solution were investigated. The results showed that the film nanocomposite had an outstanding release-control effect. The addition of MCM-41 nanoparticles also improved the mechanical properties of zein films. The antibacterial effect of CEO was significantly prolonged by the film nanocomposite; indicating the CEO film nanocomposite fabricated via modified supercritical CO2 impregnation was a potential long-term antibacterial medicine or food package material.

Precise Dissolution Control and Bioavailability Evaluation for Insoluble Drug Berberine via a Polymeric Particle Prepared Using Supercritical CO2.

It is still controversial whether poor aqueous solubility is the most primary reason for the low oral bioavailability of insoluble drugs. Therefore, in this study, berberine-loaded solid polymeric particles (BPs) of varied dissolution profiles with ß-cyclodextrin (ß-CD) as carrier were fabricated using solution-enhanced dispersion by supercritical fluids (SEDS), and the relationship between dissolution and berberine (BBR) bioavailability was evaluated. Dissolution property was controlled via particle morphology manipulation, which was achieved by adjusting several key operating parameters during the SEDS process. Characterization on BP using infrared spectroscopy, differential scanning calorimetry, and X-ray diffraction indicated that BBR was dispersed in amorphous form, while nuclear magnetic resonance spectroscopy showed that methoxy groups of BBR were included into the cavities of ß-CD. In vivo pharmacokinetic studies showed that oral bioavailability increased by about 54% and 86% when the dissolution rate of BBR was increased by 51% and 83%, respectively. The entry speed of BBR into the bloodstream was also advanced with the degree of dissolution enhancement. It seemed that dissolution enhancement gave positive effect to the oral bioavailability of berberine, but this might not be the crucial point. Meanwhile, supercritical CO2 technology is a promising method for pharmaceutical research due to its advantages in regulating drug-dosage properties.

Reduced Staphylococcus aureus biofilm formation in the presence of chitosan-coated iron oxide nanoparticles.

Staphylococcus aureus can adhere to most foreign materials and form biofilm on the surface of medical devices. Biofilm infections are difficult to resolve. The goal of this in vitro study was to explore the use of chitosan-coated nanoparticles to prevent biofilm formation. For this purpose, S. aureus was seeded in 96-well plates to incubate with chitosan-coated iron oxide nanoparticles in order to study the efficiency of biofilm formation inhibition. The biofilm bacteria count was determined using the spread plate method; biomass formation was measured using the crystal violet staining method. Confocal laser scanning microscopy and scanning electron microscopy were used to study the biofilm formation. The results showed decreased viable bacteria numbers and biomass formation when incubated with chitosan-coated iron oxide nanoparticles at all test concentrations. Confocal laser scanning microscopy showed increased dead bacteria and thinner biofilm when incubated with nanoparticles at a concentration of 500 µg/mL. Scanning electron microscopy revealed that chitosan-coated iron oxide nanoparticles inhibited biofilm formation in polystyrene plates. Future studies should be performed to study these nanoparticles for anti-infective use.

Green synthesis of biocompatiable chitosan-graphene oxide hybrid nanosheet by ultrasonication method.

Ultrasound-induced synthesis of chitosan-modified nano-scale graphene oxide (CS-NGO) hybrid nanosheets, which has great potential pharmaceutical applications, in supercritical CO2 without catalyst was presented for the first time. The preparation process does not require organic solvent and post-processing, and CO2 easily escapes from the product. The morphology and structure of the CS-NGO, characterized using scanning electron microscopy, transmission electron microscopy, infrared spectroscopy, X-ray photoelectron spectroscopy and thermogravimetric analysis, confirms that it was combined via the amide linkage, and had excellent dispersibility and stability toward acidic and physiological aqueous solution, which implies that it could be used as a drug-carrier. The sonication power played a crucial role in inducing forming amidation, and the conversion rate increased with the sonication time. The mechanism of this reaction was explained.

Controlled morphology and size of curcumin using ultrasound in supercritical CO2 antisolvent.

Controllable morphology and size of crystal materials prepared by using a supercritical antisolvent (SAS) technique is still challenge. In this study, ultrasound was introduced into the SAS process to produce the particles of curcumin, a model compound. The effects of ultrasound power on the particle morphology and size were investigated in the range of 0 and 240 W at three different pressures. The observation of jet flow indicated ultrasound could accelerate the mixing speed between the liquid solution and the CO2, and thus reduced the gaseous region and the local saturation gradient. Mixed polymorphic and uniform particles of the curcumin were produced at a low and high mixing speed, respectively, confirmed by scanning electron microscopy. The needle- or rod-like particle, irregular lumpy particle and nano spherical particle were generated with the increase of the ultrasound power, attributed to the changes of the degree of supersaturation. Therefore, the ultrasound can be potentially applied to adjust the morphology and size of the crystal materials in supercritical CO2 antisolvent.

Influence of ultrasonic pretreatment on the yield of bio-oil prepared by thermo-chemical conversion of rice husk in hot-compressed water.

The aim of the current study is to investigate the feasibility of thermo-chemical conversion of rice husk in hot-compressed water via ultrasonic pretreatment to increase the bio-oil yield. The results show that ultrasonic pretreatment remarkably changes the structures of the rice husk, such as enhancing swelling and surface area, eroding lignin structure, and resulting in more exposure of the cellulose and hemicellulose. The highest bio-oil yield of 42.8% was obtained from the thermo-chemical conversion at 300 °C and 0 min of the residence time for the 1 h pretreated rice husk. GC-MS analysis indicates that the relative contents of phenols, 5-Hydroxymethylfurfural, and lactic acid are higher in bio-oils obtained from the pretreated rice husks than that from the raw rice husk.

Biocompatibility of chitosan-coated iron oxide nanoparticles with osteoblast cells.

BACKGROUND: Bone disorders (including osteoporosis, loosening of a prosthesis, and bone infections) are of great concern to the medical community and are difficult to cure. Therapies are available to treat such diseases, but all have drawbacks and are not specifically targeted to the site of disease. Chitosan is widely used in the biomedical community, including for orthopedic applications. The aim of the present study was to coat chitosan onto iron oxide nanoparticles and to determine its effect on the proliferation and differentiation of osteoblasts. METHODS: Nanoparticles were characterized using transmission electron microscopy, dynamic light scattering, x-ray diffraction, zeta potential, and vibrating sample magnetometry. Uptake of nanoparticles by osteoblasts was studied by transmission electron microscopy and Prussian blue staining. Viability and proliferation of osteoblasts were measured in the presence of uncoated iron oxide magnetic nanoparticles or those coated with chitosan. Lactate dehydrogenase, alkaline phosphatase, total protein synthesis, and extracellular calcium deposition was studied in the presence of the nanoparticles. RESULTS: Chitosan-coated iron oxide nanoparticles enhanced osteoblast proliferation, decreased cell membrane damage, and promoted cell differentiation, as indicated by an increase in alkaline phosphatase and extracellular calcium deposition. Chitosan-coated iron oxide nanoparticles showed good compatibility with osteoblasts. CONCLUSION: Further research is necessary to optimize magnetic nanoparticles for the treatment of bone disease.

Preparation and characterization of a molecularly imprinted polymer by grafting on silica supports: a selective sorbent for patulin toxin.

A new molecularly imprinted polymer (MIP) has been prepared on silica beads using the radical "grafting from" polymerization method for selective extraction of minor contaminant mycotoxin of patulin (PTL). After the introduction of amino groups onto the silica surface with 3-aminopropyltriethoxysilane, azo initiator onto the silica surface was achieved by the reaction of surface amino groups with 4,4'-azobis(4-cyanopentanoic acid). The scale-up synthesis of MIP was then carried out in the presence of 6-hydroxynicotinic acid as template substitute, functional, and cross-linking monomers. The prepared sorbent was characterized using FT-IR spectroscopy, scanning electron microscopy, elemental analysis, and the adsorption-desorption selectivity, and the capacity characteristic of the polymer was investigated by a conventional batch adsorption test and Scatchard plot analysis. The results indicated that coated polymers had specific adsorption to PTL as compared with its co-occurring 5-hydroxymethyl-2-furaldehyde (hydroxymethylfurfural (HMF)), at the same bulk concentration for solution of PTL and HMF, the maximum absorbance in the solid-phase extraction (SPE) method to PTL were 93.97% or 0.654 µg/mg while to HMF they were 76.89% or 0.496 µg/mg. Scatchard analysis revealed that two classes of binding sites were formed in PTL-MIP with dissociation constants of 3.2 × 10(-2) and 5.0 × 10(-3) mg/mL and the affinity binding sites of 8.029 and 1.364 mg/g, respectively. The recoveries of PTL were more than 90% for the developed MISPE and around 75% for the traditional liquid-liquid extraction in spiked apple juice samples. It was concluded that the method is suitable for the scale-up synthesis of PTL-MIP grafted on silica, and the polymer can be effectively applied as SPE coupled with high-performance liquid chromatography (HPLC) for the determination of PTL in apple juice or other related products.