ABSTRACT
The increasing use of transparent ceramics in laser systems presents a challenge; their low damage threshold has become a significant impediment to the development of powerful laser systems. Consequently, it is imperative to undertake research into the damage sustained by these materials. Micropores, the most common structural defects in transparent ceramics, inevitably remain within the material during its preparation process. However, the relationship between the density and size of these micropores and their impact on nanosecond laser damage threshold and damage evolution remains unclear. In this study, we utilize the annealing process to effectively manage the density and size of micropores, establishing a correlation between micropores in relation to damage thresholds. This study confirms for the first time that micropores significantly contribute to laser damage, comparing and analyzing the damage morphology characteristics of both front and rear surfaces of transparent ceramics. It also presents, potential mechanisms that may contribute to these differences in damage. This paper offers guidance for controlling micropores during the preparation and processing of transparent ceramics with high laser damage thresholds. The findings are expected to further improve the anti-nanosecond laser damage capabilities of transparent ceramics.
ABSTRACT
Fabrication of glass with complex geocd the low resolution of particle-based or fused glass technologies. Herein, a high-resolution 3D printing of transparent nanoporous glass is presented, by the combination of transparent photo-curable sol-gel printing compositions and digital light processing (DLP) technology. Multi-component glass, including binary (Al2 O3 -SiO2 ), ternary (ZnO-Al2 O3 -SiO2 , TiO2 -Al2 O3 -SiO2 ), and quaternary oxide (CaO-P2 O5 -Al2 O3 -SiO2 ) nanoporous glass objects with complex shapes, high spatial resolutions, and multi-oxide chemical compositions are fabricated, by DLP printing and subsequent sintering process. The uniform nanopores of Al2 O3 -SiO2 -based nanoporous glasses with the diameter (≈6.04 nm), which is much smaller than the visible light wavelength, result in high transmittance (>95%) at the visible range. The high surface area of printed glass objectives allows post-functionalization via the adsorption of functional guest molecules. The photoluminescence and hydrophobic modification of 3D printed glass objectives are successfully demonstrated. This work extends the scope of 3D printing to transparent nanoporous glasses with complex geometry and facile functionalization, making them available for a wide range of applications.
ABSTRACT
The growth and laser amplifier performance of a large-aperture Nd:LuAG ceramic are reported. Using the vacuum sintering and high-temperature insostatic pressing (HIP) methods, three pieces of a 50 mm-aperture Nd:LuAG ceramic are fabricated and used as the gain medium in a diode-pumped nanosecond distributed active mirror amplifier chain (DAMAC). The energy storage capacity of large-aperture Nd:LuAG is investigated and compared with that of Nd:YAG. Energy amplification up to 10.3 J at 10 Hz is achieved, which, to the best of our knowledge, produces the highest peak power (1 GW) using Nd:LuAG. The excellent energy storage and extraction performance confirm the great potential of Nd:LuAG in high-energy scaling.
ABSTRACT
In the present study, a tough tetragonal zirconia polycrystalline (Y-TZP) material was developed for use in high-speed infrared windows and domes. The influence of the preparation procedure and the microstructure on the material's optical properties was evaluated by SEM and FT-IR spectroscopy. It was revealed that a high transmittance up to 77% in the three- to five-micrometer IR region could be obtained when the sample was pre-sintered at 1225 °C and subjected to hot isostatic pressing (HIP) at 1275 °C for two hours. The infrared transmittance and emittance at elevated temperature were also examined. The in-line transmittance remained stable as the temperature increased to 427 °C, with degradation being observed only near the infrared cutoff edge. Additionally, the emittance property of 3Y-TZP ceramic at high temperature was found to be superior to those of sapphire and spinel. Overall, the results indicate that Y-TZP ceramic is a potential candidate for high-speed infrared windows and domes.
ABSTRACT
Er(3+)-doped transparent glass ceramics containing micron-sized SrF2 crystals were obtained by direct liquid-phase sintering of a mixture of SrF2 powders and precursor glass powders at 820 °C for 15 min. The appearance and microstructural evolution of the SrF2 crystals in the resulting glass ceramics were investigated using X-ray diffraction, field-emission scanning electron microscopy and transmission microscopy. The SrF2 crystals are ~15 µm in size and are uniformly distributed throughout the fluorophosphate glass matrix. The glass ceramics achieve an average transmittance of 75% in the visible region and more than 85% in the near-IR region. The high transmittance of the glass ceramics results from matching the refractive index of the SrF2 with that of the precursor glass. Energy dispersive spectroscopy, photoluminescence spectra, and photoluminescence lifetimes verified the incorporation of Er(3+) into the micron-sized SrF2 crystals. Intense 2.7 µm emissions due to the (4)I11/2 â (4)I13/2 transition were observed upon excitation at 980 nm using a laser diode. The maximum value of the emission cross section of Er(3+) around 2.7 µm is more than 1.2 × 10(-20) cm(2), which indicates the potential of using transparent glass ceramics containing micron-sized SrF2 crystals for efficient 2.7 µm lasers and amplifiers.
ABSTRACT
The operation of a mid-infrared laser at 2244 nm in a Cr:ZnS polycrystalline channel waveguide fabricated using direct femtosecond laser writing with a helical movement technique is demonstrated. A maximum power output of 78 mW and an optical-to-optical slope efficiency of 8.6% are achieved. The compact waveguide structure with 2 mm length was obtained through direct femtosecond laser writing, which was moved on a helical trajectory along the laser medium axis and parallel to the writing direction.
ABSTRACT
The synthesis of pure and well dispersed lutetium aluminum garnet (LuAG) powder is crucial and important for the preparation of LuAG transparent ceramics. In this paper, high purity and well dispersed LuAG powders have been synthesized via co-precipitation method with lutetium nitrate and aluminum nitrate as raw materials. Ammonium hydrogen carbonate (AHC) was used as the precipitant. The influence of aging time, pH value, and dripping speed on the prepared LuAG powders were investigated. It showed that long aging duration (>15 h) with high terminal pH value (>7.80) resulted in segregation of rhombus Lu precipitate and Al precipitate. By decreasing the initial pH value or accelerating the dripping speed, rhombus Lu precipitate was eliminated and pure LuAG nano powders were synthesized. High quality LuAG transparent ceramics with transmission >75% at 1064 nm were fabricated using these well dispersed nano LuAG powders.
ABSTRACT
Employing high-yield production of layered materials by liquid-phase exfoliation, molybdenum disulfide (MoS2) dispersions with large populations of single and few layers were prepared. Electron microscopy verified the high quality of the two-dimensional MoS2 nanostructures. Atomic force microscopy analysis revealed that ~39% of the MoS2 flakes had thicknesses of less than 5 nm. Linewidth and frequency difference of the E(1)2g and A1g Raman modes confirmed the effective reduction of flake thicknesses from the bulk MoS2 to the dispersions. Ultrafast nonlinear optical (NLO) properties were investigated using an open-aperture Z-scan technique. All experiments were performed using 100 fs pulses at 800 nm from a mode-locked Ti:sapphire laser. The MoS2 nanosheets exhibited significant saturable absorption (SA) for the femtosecond pulses, resulting in the third-order NLO susceptibility Imχ((3)) ~ 10(-15) esu, figure of merit ~10(-15) esu cm, and free-carrier absorption cross section ~10(-17) cm(2). Induced free carrier density and the relaxation time were estimated to be ~10(16) cm(-3) and ~30 fs, respectively. At the same excitation condition, the MoS2 dispersions show better SA response than the graphene dispersions.
ABSTRACT
We demonstrated a hybrid ceramic master-oscillator high-power fiber amplifier with a diode-pumped Yb:YAG ceramic laser as the seeding oscillator, which was passively mode-locked at 103.29 MHz repetition rate around 1031 nm by using a semiconductor saturable absorption mirror, and a two-stage double-clad photonic crystal fiber amplifier, which power-scaled the ceramic laser oscillator up to an average power of 303 W. The amplified pulses were further compressed to 237 and 418 fs at 50 and 150 W output powers, respectively. The compressed pulses exhibited about 0.05% deviation from the Gaussian fit, implying that the high-power fiber amplification induced neither observable temporal and spectral distortion nor significant nonlinear de-chirping of the chirped pulses.
ABSTRACT
Characteristics of Tm:YAG ceramic for high efficient 2-µm lasers are analyzed. Efficient diode end-pumped continuous-wave and Q-switched Tm:YAG ceramic lasers are demonstrated. At the absorbed pump power of 53.2W, the maximum continuous wave (cw) output power of 17.2 W around 2016 nm was obtained with the output transmission of 5%. The optical conversion efficiency is 32.3%, corresponding to a slope efficiency of 36.5%. For Q-switched operation, the shortest width of 69 ns was achieved with the pulse repetition frequency of 500 Hz and single pulse energy of 20.4 mJ, which indicates excellent energy storage capability of the Tm:YAG ceramic.
Subject(s)
Ceramics/chemistry , Lasers, Solid-State , Signal Processing, Computer-Assisted/instrumentation , Computer-Aided Design , Energy Transfer , Equipment Design , Equipment Failure AnalysisABSTRACT
We demonstrated a high-power continuous-wave (CW) polycrystalline Yb:YAG ceramic laser pumped by fiber-pigtailed laser diode at 968 nm with 400 mum fiber core. The Yb:YAG ceramic laser performance was compared for different Yb(3+) ion concentrations in the ceramics by using a conventional end-pump laser cavity consisting of two flat mirrors with output couplers of different transmissions. A CW laser output of 40 W average power with M(2) factor of 5.8 was obtained with 5 mol% Yb concentration under 120 W incident pump power. This is to the best of our knowledge the highest output power in end-pumped bulk Yb:YAG ceramic laser.
Subject(s)
Ceramics , Lasers, Semiconductor , Lasers, Solid-State , Computer-Aided Design , Equipment Design , Equipment Failure Analysis , Reproducibility of Results , Sensitivity and SpecificityABSTRACT
Yb:YAG single crystals with Yb doping concentration 5.4, 16.3, 27.1, 53.6, and 100 at.% were grown by the Czochralski process. The effects of Yb concentration on the absorption spectra (190-1100 nm), fluorescence spectra under 940 nm and X-ray excitation were studied. The concentration quenching of fluorescence was observed when the Yb doping concentration reaches to as high as 27.1at.% for Yb:YAG. Under 940 nm excitation, the influence of the self-absorption at 969 and 1029 nm on the fluorescence spectra is not evident when the Yb doping concentration is as high as 27.1at.%. However, it can greatly change the shape of fluorescence spectra of Yb:YAG when the Yb doping concentration reaches to above 53.6 at.%.
Subject(s)
Aluminum/chemistry , Spectrometry, Fluorescence , Ytterbium/analysis , Yttrium/chemistry , CrystallizationABSTRACT
Yb(3)Al(5)O(12) single crystal has been grown by Czochralski (CZ) method. The absorption spectrum was investigated at low temperature and the electronic energy levels for (2)F(5/2) multiplet of Yb(3+) in YbAG was proposed. The up-conversion emission of the crystal under 940 nm diode pumping and the X-ray excited luminescence (XEL) features of the crystal were also studied.
