ABSTRACT
Exposing catalytically active metal sites in metal-organic frameworks (MOFs) while maintaining porosity is beneficial for increasing electron transport to achieve better electrochemical energy conversion performance. Herein, we propose an in situ method for MOF formation and loading onto TiO2 nanorods (NR) using a simple solution-processable method followed by annealing to obtain TiO2-Co3O4. The as-prepared TiO2-ZIF-67 based photoanodes were annealed at 350, 450, and 550 °C to study the effect of carbonization on photo-electrochemical water oxidation. The successful loading of ZIF-67 on TiO2 and the formation of TiO2-Co3O4 heterojunction were confirmed by XRD, XPS, FE-SEM, and HRTEM analyses. TiO2-Co3O4-450 (the sample annealed at 450 °C) showed an enhanced photocurrent of 2.4 mA/cm2, which was 2.6 times larger than that of pristine TiO2. The improved photocurrent might be ascribed to the prepared p-n heterostructures (Co3O4 and TiO2), which promote electron-hole separation and charge transfer within the system and improve the photoelectrochemical performance. Moreover, the preparation of Co3O4 from the MOF carbonization process improved the electrical conductivity and significantly increased the number of exposed active sites and enhanced the photoresponse performance. The as-prepared ZIF-67 derived TiO2-Co3O4 based photoanodes demonstrate high PEC water oxidation, and the controlled carbonization method paves the way toward the synthesis of low-cost and efficient electrocatalysts.
ABSTRACT
In this study, we investigated the effect of the stacking order of metal precursors on the formation of volume defects, such as blisters and nanopores, in CZTSSe thin-film solar cells. We fabricated CZTSSe thin films using three types of metal-precursor combinations, namely, Zn/Cu/Sn/Mo, Cu/Zn/Sn/Mo, and Sn/Cu/Zn/Mo, and studied the blister formation. The blister-formation mechanism was based on the delamination model, taking into consideration the compressive stress and adhesion properties. A compressive stress could be induced during the preferential formation of a ZnSSe shell. Under this stress, the adhesion between the ZnSSe film and the Mo substrate could be maintained by the surface tension of a metallic liquid phase with good wettability, or by the functioning of ZnSSe pillars as anchors, depending on the type of metal precursor used. Additionally, the nanopore formation near the back-contact side was found to be induced by the columnar microstructure of the metal precursor with the Cu/Zn/Mo stacking order and its dezincification. Based on the two volume-defect-formation mechanisms proposed herein, further development of volume-defect-formation suppression technology is expected to be made.
ABSTRACT
We synthesized novel organic photosensitizers based on fluorine-substituted phenothiazine with thiophene bridge units in the chromophore for application in dye-sensitized solar cells (DSSCs). Furthermore, organic dyes with different acceptors exhibited higher molar extinction coefficients, and better light absorption at longer wavelengths. The photovoltaic properties of organic dyes composed of different acceptors in their chromophores were measured to identify their effects on the DSSC performance. The organic dye, PFSCN2 containing multi-cyanoacrylic acid as the electron acceptor, showed a power conversion efficiency of 4.67% under AM 1.5 illumination (100 mW/cm2). The retarded recombination kinetics from TiO2 electrode to electrolyte enhanced the electron life time of the organic dye, PFSCN2 in the photoanode of the DSSC. This was confirmed with impedance analysis.
Subject(s)
Coloring Agents/chemistry , Electric Power Supplies , Phenothiazines/chemistry , Solar Energy , Absorption, Radiation , Electrochemistry , Light , Optical PhenomenaABSTRACT
In this study, we report synthesis and growth of rutile-anatase TiO2 thin film on fluorine-doped tin oxide (FTO) glass by a two-step hydrothermal method. The effects of additional treatments (i.e., TiCl4 post-treatment and seed layer formation were also studied. Photocurrent-voltage (I-V) measurement of rutile-anatase TiO2 thin film was performed under 1.5 G light illumination. Photovoltaic performance was investigated by incident photon-to-electron conversion efficiency (IPCE), electrochemical impedance spectroscopy (EIS), intensity-modulated photocurrent/photovoltage spectroscopy (IMVS/IMPS) and open-circuit photovoltage decay (OCVD).
