A Comprehensive Approach for Designing Low Carbon Wood Bio-Concretes.

This paper presents a method for designing low carbon bio-based building materials, also named bio-concretes, produced with wood wastes in shavings form (WS) and cementitious pastes. As the aggregates phase of bio-concretes is composed of plant-based particles, known as porous and high water-absorbing materials, the bio-concretes cannot be designed by using the traditional design rules used for conventional mortar or concrete. Then, the method used in the current paper is an adaptation of a previous one that has been developed in a recent paper where bio-concretes were produced with a cement matrix, three types of bio-aggregates, and a proposal of a design abacus. However, when that abacus is used for designing WBC with low cement content in the matrix, the target compressive strength is not reached. In the present paper, the method is extended to low cement content matrix (up to 70% of cement substitution) and also considering the greenhouse gas (GHG) emission of the WBC. To obtain data for proposing a new design abacus, an experimental program was carried out by producing nine workable WBCs, varying wood volumetric fractions (40-45-50%), and water-to-binder ratios. The bio-concretes produced presented adequate consistency, lightness (density between 715 and 1207 kg/m3), and compressive strength ranging from 0.64 to 12.27 MPa. In addition, the GHG emissions of the WBC were analysed through the Life Cycle Assessment methodology. From the relationships obtained between density, compressive strength, water-to-binder ratio, cement consumption, and GHG emissions of the WBC, calibration constants were proposed for developing the updated and more complete abacus regarding an integrated mix design methodology.

Relation between Shear Stresses and Flexural Tensile Stresses from Standardized Tests of Extracted Prismatic Specimens of an SFRC Bridge Girder.

Experimental research on the direct shear behavior of fiber-reinforced concrete is often carried out using prisms molded with specific dimensions for a standardized test. However, the flow of fresh concrete in these molds can be different than in the case of a full-scale structural element. This is important considering that the flow direction highly influences the distribution and orientation of fibers. In addition, most of the studies did not relate their shear results to other mechanical properties. In contrast, this study attempted to deepen the experimental knowledge of the crack propagation of a steel fiber-reinforced concrete (SFRC) used in a full-scale prototype of a bridge box girder built in the laboratory. Prismatic specimens were sawn from webs and top flanges of this prototype. Serving as references, additional specimens were molded in wooden boxes. In a previous study of our research group, both had been tested under a three-point notched bending configuration maintaining test conditions proportional to the EN14651 specifications. From each of the previously flexurally tested specimens, two prismatic specimens suitable for the Fédération Internationale de la Précontrainte (FIP) shear test setup were extracted by adopting a cutting methodology that avoided the damage induced by the flexural tests to be part of the FIP specimens. These FIP specimens were tested in almost pure shear loading conditions for assessing the performance of SFRC. Computer tomography images and photos of the shear failure faces were used to determine the distribution and density of fibers. The results demonstrated that the peak loads were proportional to the fiber density at the shear failure section. Assuming that the SFRC conditions of the webs were representative of a common batching procedure in the construction industry, the results from the tests in specimens extracted from these webs were adopted to establish shear stress/flexural tensile stress ratios vs. crack mouth opening displacement curves. The curves belonging to cross-sections of a similar fiber density in the shear and flexural cases allowed for the proposal of a normalized crack-dilatancy relation composed of three stages of the crack propagation. In addition, a trilinear crack width-slip relation was established using the same set of specimens. The relevancy of this proposal is that the shear response can be estimated from a widely accepted standardized flexural test, which demands a simpler instrumentation and is also easier to execute than the shear setup.

Transgenerational effects of a hypercaloric diet.

The effects of a maternal hypercaloric diet (HD) during puberty and early adulthood on neuroimmune aspects in offspring were investigated. In female rats of the F0 generation and male rats of the F1 generation, bodyweight (BW) gain, retroperitoneal fat (RPF) weight, the number of hypodermic adipocytes (HAs) and expression of glial fibrillary acidic protein (GFAP) were measured in hypothalamic astrocytes. On Postnatal Day 50, the F1 pups were challenged with lipopolysaccharide (LPS, 100µgkg-1, s.c.) or an equal volume of saline (S), and behaviour in the open field test was evaluated, as were plasma neuropeptide and cytokine concentrations. The maternal HD caused the female F0 rats to become overweight. The F1 offspring of dams fed the HD and challenged with saline (HDS group) exhibited increases in BW gain, RPF weight and in the number of large HAs and a decrease in GFAP immunoreactivity. F1 offspring of dams fed the HD and challenged with LPS (HDLPS group) exhibited decreases in BW gain, RPF weight and GFAP immunoreactivity, but no differences were observed in the number of larger and small HAs. Plasma tumour necrosis factor-α concentrations were high in the HDS and HDLPS groups. Thus, the maternal HD during puberty and early adulthood caused the F1 generation to become overweight despite the fact that they received a normocaloric diet. These results indicate a transgenerational effect of the HD that may occur, in part, through permanent changes in immune system programming. The attenuation of neuroinflammation biomarkers after LPS administration may have resulted in a decrease in the number of adipocytes, which, in turn, reduced cytokine, adipokine and chemokine levels, which are able to recruit inflammatory cells in adipose tissue.

Maternal food restriction in rats of the F0 generation increases retroperitoneal fat, the number and size of adipocytes and induces periventricular astrogliosis in female F1 and male F2 generations.

The present study investigated whether male offspring (F2 generation) from female rats (F1 generation) whose mothers (F0 generation) were food restricted during gestation inherit a phenotypic transgenerational tendency towards being overweight and obese in the juvenile period, in the absence of food restriction in the F1/F2 generations. Dams of the F0 generation were 40% food restricted during pregnancy. Bodyweight, the number and size of larger and small hypodermal adipocytes (HAs), total retroperitoneal fat (RPF) weight and the expression of glial fibrillary acidic protein (GFAP) in periventricular hypothalamic astrocytes (PHAs), as determined by immunohistochemistry, were evaluated in both generations. In the female F1 generation, there was low bodyweight gain only during the juvenile period (30-65 days of age), a decrease in the size of small adipocytes, an increase in the number of small adipocytes, an increase in RPF weight and an increase in GFAP expression in PHAs at 90-95 days of age. In males of the F2 generation at 50 days of age, there was increased bodyweight and RPF weight, and a small number of adipocytes and GFAP expression in PHAs. These data indicate that the phenotypic transgenerational tendency towards being overweight and obese was observed in females (F1) from mothers (F0) that were prenatally food restricted was transmitted to their male offspring.