ABSTRACT
Memristive devices are promising candidates to emulate biological computing. However, the typical switching voltages (0.2-2 V) in previously described devices are much higher than the amplitude in biological counterparts. Here we demonstrate a type of diffusive memristor, fabricated from the protein nanowires harvested from the bacterium Geobacter sulfurreducens, that functions at the biological voltages of 40-100 mV. Memristive function at biological voltages is possible because the protein nanowires catalyze metallization. Artificial neurons built from these memristors not only function at biological action potentials (e.g., 100 mV, 1 ms) but also exhibit temporal integration close to that in biological neurons. The potential of using the memristor to directly process biosensing signals is also demonstrated.
Subject(s)
Action Potentials , Electronics/instrumentation , Geobacter/metabolism , Nanowires/chemistry , Neurons , Biosensing Techniques , Electricity , Equipment Design , Humans , Molecular Dynamics Simulation , Nanotechnology/instrumentation , Nanowires/ultrastructure , Neural Networks, Computer , Synapses/metabolism , Wearable Electronic DevicesABSTRACT
We report the observation of two resistance switching modes in certain 50 nm × 50 nm crossbar TiO(2) memristive devices that have been electroformed with a low-current process. The two switching modes showed opposite switching polarities. The intermediate state was shared by both modes (the ON state of the high-resistance mode or the OFF state of the low-resistance mode) and exhibited a relaxation to a more resistive state, including an initial transient decay. The activation energies of such a decay and ON-switching to the intermediate state were determined to be 50-210 meV and 1.1 eV, respectively. Although they are attributed to the coexistence of charge trapping and ionic motion, the ionic motion dominates in both switching modes. Our results indicate that the two switching modes in our system correspond to different switching layers adjacent to the interfaces at the top and bottom electrodes.
ABSTRACT
We used spatially-resolved NEXAFS (near-edge x-ray absorption fine structure) spectroscopy coupled with microscopy to characterize the electronic, structural and chemical properties of bipolar resistive switching devices. Metal/TiO2/metal devices were electroformed with both bias polarities and then physically opened to study the resulting material changes within the device. Soft x-ray absorption techniques allowed isolated study of the different materials present in the device with 100 nm spatial resolution. The resulting morphology and structural changes reveal a picture of localized polarity-independent heating occurring within these devices initiated by and subsequently accelerating polarity-dependent electrochemical reduction/oxidation processes.
ABSTRACT
Metal and semiconductor oxides are ubiquitous electronic materials. Normally insulating, oxides can change behavior under high electric fields--through 'electroforming' or 'breakdown'--critically affecting CMOS (complementary metal-oxide-semiconductor) logic, DRAM (dynamic random access memory) and flash memory, and tunnel barrier oxides. An initial irreversible electroforming process has been invariably required for obtaining metal oxide resistance switches, which may open urgently needed new avenues for advanced computer memory and logic circuits including ultra-dense non-volatile random access memory (NVRAM) and adaptive neuromorphic logic circuits. This electrical switching arises from the coupled motion of electrons and ions within the oxide material, as one of the first recognized examples of a memristor (memory-resistor) device, the fourth fundamental passive circuit element originally predicted in 1971 by Chua. A lack of device repeatability has limited technological implementation of oxide switches, however. Here we explain the nature of the oxide electroforming as an electro-reduction and vacancy creation process caused by high electric fields and enhanced by electrical Joule heating with direct experimental evidence. Oxygen vacancies are created and drift towards the cathode, forming localized conducting channels in the oxide. Simultaneously, O(2-) ions drift towards the anode where they evolve O(2) gas, causing physical deformation of the junction. The problematic gas eruption and physical deformation are mitigated by shrinking to the nanoscale and controlling the electroforming voltage polarity. Better yet, electroforming problems can be largely eliminated by engineering the device structure to remove 'bulk' oxide effects in favor of interface-controlled electronic switching.
