Small-Angle X-ray Scattering (SAXS) Used for the Identification of Nicomorphine Polymorphic Changes at the Early Stage to Avoid Varied Stability and Possible Side Effects.

In this paper, we present the identification of polymorphisms at an early stage, identified by applying non-standard methods such as SAXS. We provide an analytical approach to polymorphism in the quality/purity of an active pharmaceutical ingredient (API), supplied to a generic company by two different suppliers (i.e., manufacturers). Changes in thermodynamic polymorphism firstly become visible in traces in the larger crystal lattices, which are visible on the SAXS spectrum only using the logarithmic scale, as shown in the result figures. Hence, we are here on the trail of the beginning of a new polymorph in nicomorphine, whose crystal waviness at the early stage is visible only in the additional symmetrical peaks identified and calculated using SAXS, while the chemical analyses excluded all kinds of chemical impurities. The chemical and structural properties were studied using the following techniques: SAXS, WAXS, DSC, dissolution, Raman spectroscopy, and FTIR. Only the SAXS technique could identify crucial differences and calculate the additional signals related to giant crystals, whilst a standard method such as WAXS showed none, and nor did the chemical analyses, such as Raman spectroscopy and FT-IR. This means that due to water in crystallization (known in nicomorphine) or thermodynamic waviness, the formation of the new polymorph starts first in traces, which become visible at larger distances from the crystal lattice, detectible only in the SAXS range. This is a very important premise and hypothesis for further research, and we believe that this work lays a new stone in understanding the origin of new unknown polymorphs and their mixtures. Therefore, the aim of this work is to show that the use of non-standard methods (i.e., SAXS) can be of great benefit to API analysis and the identification of polymorphic changes in the early phase, which can cause varied stability, solubility and bioavailability and thus different therapeutic effects or side effects.

Simulation and Optimization of FAPbI3 Perovskite Solar Cells with a BaTiO3 Layer for Efficiency Enhancement.

Since the addition of BaTiO3 in perovskite solar cells (PSCs) provides a more energetically favorable transport route for electrons, resulting in more efficient charge separation and electron extraction, in this work we experimentally prepared such a PSC and used a modeling approach to point out which simulation parameters have an influence on PSC characteristics and how they can be improved. We added a layer of BaTiO3 onto the TiO2 electron transport layer and prepared a PSC, which had an FTO/TiO2/BaTiO3/FAPbI3/spiro-OMeTAD/Au architecture with a power conversion efficiency (PCE) of 11%. Further, we used the simulation program SCAPS-1D to investigate and optimize the device parameters (thickness of the BaTiO3 and absorber layers, doping, and defect concentration) resulting in devices with PCEs reaching up to 15%, and even up to 20% if we assume an ideal structure with no interlayer defects. Our experimental findings and simulations in this paper highlight the promising interplay of multilayer TiO2/BaTiO3 ETLs for potential future applications in PSCs.

Surface Morphology of Textured Transparent Conductive Oxide Thin Film Seen by Various Probes: Visible Light, X-rays, Electron Scattering and Contact Probe.

Fluorine-doped tin oxide thin films (SnO2:F) are widely used as transparent conductive oxide electrodes in thin-film solar cells because of their appropriate electrical and optical properties. The surface morphology of these films influences their optical properties and therefore plays an important role in the overall efficiencies of the solar cells in which they are implemented. At rough surfaces light is diffusely scattered, extending the optical path of light inside the active layer of the solar cell, which in term improves light absorption and solar cell conversion efficiency. In this work, we investigated the surface morphology of undoped and doped SnO2 thin films and their influence on the optical properties of the films. We have compared and analysed the results obtained by several complementary methods for thin-film surface morphology investigation: atomic force microscopy (AFM), transmission electron microscopy (TEM), and grazing-incidence small-angle X-ray scattering (GISAXS). Based on the AFM and TEM results we propose a theoretical model that reproduces well the GISAXS scattering patterns.

Simulating the Performance of a Formamidinium Based Mixed Cation Lead Halide Perovskite Solar Cell.

With the aim of decreasing the number of experiments to obtain a perovskite solar cell (PSC) with maximum theoretical efficiency, in this paper, PSC performance was studied using the program solar cell capacitance simulator (SCAPS-1D). The PSC with the architecture ITO/TiO2/perovskite/spiro-MeOTAD/Au was investigated, while the selected perovskite was mixed cation Rb0.05Cs0.1FA0.85PbI3. The analysis was based on an experimentally prepared solar cell with a power conversion efficiency of ~7%. The PSC performance, verified by short-circuit current density (Jsc), open-circuit voltage (Voc), fill factor (FF) and power conversion efficiency (PCE), was studied by optimization of the simulation parameters responsible for improvement of the cell operation. The optimized parameters were absorber layer thickness, doping, defect concentration and the influence of the resistivity (the net effect of ohmic loss, Rs and the leakage current loss represented by the resistivity, Rshunt). The results of SCAPS-1D simulations estimated the theoretical power conversion efficiency of 15% for our material. We have showed that the main contribution to improvement of solar cell efficiency comes with lowering ohmic resistivity of the cell as well as doping and defect concentration, because their concentration is proportional to recombination rate.

Novel, Simple and Low-Cost Preparation of Ba-Modified TiO2 Nanotubes for Diclofenac Degradation under UV/Vis Radiation.

A novel low-cost synthesis of barium-modified TiO2 nanotube (TNT) arrays was used to obtain an immobilized photocatalyst for degradation of diclofenac. TNT arrays were prepared by electrochemical anodization of titanium thin films deposited on fluorine-doped tin oxide (FTO) coated glass by magnetron sputtering, ensuring transparency and immobilization of the nanotubes. The Ba-modifications were obtained by annealing solutions of Ba(OH)2 spin coated on top of TNT. Three different concentrations of Ba(OH)2 were used (12.5 mM, 25 mM and 50 mM). The crystalline structure, morphology and presence of Ba were characterized by X-ray diffraction, scanning electron microscopy and energy dispersive X-ray spectroscopy, respectively. Ba-modified TiO2 nanotubes (BTNT) were tested for photocatalytic degradation of diclofenac under UV/Vis radiation and it was proven that all of the Ba-modified samples showed an increase in photocatalytic activity with respect to the unmodified TNTs. The most efficient photocatalyst was the sample prepared with 25 mM Ba(OH)2 which showed 90% diclofenac degradation after 60 min. This result was in agreement with cyclic voltammetry measurements that showed the largest increase in photo-oxidation current densities for the same sample due to the increased generation of •OH radicals obtained by a more efficient photogenerated charge separation.

Formamidinium Lead Iodide Perovskite Films with Polyvinylpyrrolidone Additive for Active Layer in Perovskite Solar Cells, Enhanced Stability and Electrical Conductivity.

In this paper, we studied the influence of polyvinylpyrrolidone (PVP) as a stabilization additive on optical and electrical properties of perovskite formamidinium lead iodide (FAPI) polycrystalline thin films on ZnO nanorods (ZNR). FAPI (as an active layer) was deposited from a single solution on ZNR (low temperature processed electron transport layer) using a one-step method with the inclusion of an anti-solvent. The role of PVP in the formation of the active layer was investigated by scanning electron microscopy and contact angle measurements to observe the effect on morphology, while X-ray diffraction was used as a method to study the stability of the film in an ambient environment. The effect of the PVP additive on the optical and electrical properties of the perovskite thin films was studied via photoluminescence, UV-Vis measurements, and electrical impedance spectroscopy. We have demonstrated that PVP inclusion in solution-processed perovskite FAPI thin films prevents the degradation of the film in an ambient atmosphere after aging for 2 months. The inclusion of the PVP also improves the infiltration of FAPI perovskite into ZnO nanostructures, increases electrical conductivity and radiative recombination of the photo-generated charge carriers. These results show promising information for promoting PVP stabilized FAPI perovskites for the new generation of photovoltaic devices.

Origin of Mangetotransport Properties in APCVD Deposited Tin Oxide Thin Films.

Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO2), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80-200 nm), and on a smaller scale in form of crystallites (10-25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1-3 × 1020 cm-3 and 10-20 cm2/Vs, which are typical values for SnO2 films, and show a negligible temperature dependence from room temperature down to -269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO2 samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

ZnO@TiO2 Core Shell Nanorod Arrays with Tailored Structural, Electrical, and Optical Properties for Photovoltaic Application.

ZnO has prominent electron transport and optical properties, beneficial for photovoltaic application, but its surface is prone to the formation of defects. To overcome this problem, we deposited nanostructured TiO2 thin film on ZnO nanorods to form a stable shell. ZnO nanorods synthesized by wet-chemistry are single crystals. Three different procedures for deposition of TiO2 were applied. The influence of preparation methods and parameters on the structure, morphology, electrical and optical properties were studied. Nanostructured TiO2 shells show different morphologies dependent on deposition methods: (1) separated nanoparticles (by pulsed laser deposition (PLD) in Ar), (2) a layer with nonhomogeneous thickness (by PLD in vacuum or DC reactive magnetron sputtering), and (3) a homogenous thin layer along the nanorods (by chemical deposition). Based on the structural study, we chose the preparation parameters to obtain an anatase structure of the TiO2 shell. Impedance spectroscopy shows pure electron conductivity that was considerably better in all the ZnO@TiO2 than in bare ZnO nanorods or TiO2 layers. The best conductivity among the studied samples and the lowest activation energy was observed for the sample with a chemically deposited TiO2 shell. Higher transparency in the visible part of spectrum was achieved for the sample with a homogenous TiO2 layer along the nanorods, then in the samples with a layer of varying thickness.

Comprehensive characterization of nanostructured lipid carriers using laboratory and synchrotron X-ray scattering and diffraction.

The development of lipid nanoparticles requires knowledge on the crystalline structure, polymorphic transitions and lipid-drug interactions. This study aimed at introducing advanced techniques to characterize nanostructured lipid carriers (NLC) comprising palmitic acid, oleic acid, stabilizer and Domperidone. Crystallinity of single components and mixtures was investigated by laboratory Small Angle X-ray Scattering (SAXS). NLC were studied with laboratory Small and Wide Angle X-ray Scattering (SWAXS). Photon Correlation Spectroscopy and Freeze Fracture Transmission Electron Microscopy were used to monitor particle size, zeta potential and shape. Stability of NLC was investigated using synchrotron X-ray Diffraction (XRD) and SAXS and laboratory SAXS. Palmitic acid showed a lamellar structure (polymorph C), which was still present after particle preparation. Spherical 300 nm-sized particles with zeta potential values above -30 mV were obtained and Domperidone was incorporated in its amorphous form. During storage, no differences in synchrotron XRD spectra were seen. However, laboratory SAXS measurements showed a second lamellar structure, identified as polymorph B. Synchrotron SAXS temperature scans confirmed that polymorph B did not affect the morphology of the encapsulated drug or the shape of NLC. These results highlight the unique capabilities of laboratory and synchrotron X-ray Scattering and Diffraction for improved structural characterization of lipid nanoparticles.

Tuning the Properties of Periodic Mesoporous Organosilica Films for Low-k Application by Gemini Surfactants.

Periodic mesoporous organosilica (PMO) thin films were synthesized by evaporation-induced self-assembly of 1,2-bis(triethoxysilyl)ethane and an ionic Gemini 16-12-16 surfactant under acidic conditions. The films were characterized by Fourier-transform infrared spectroscopy, grazing-incidence small-angle X-ray scattering, ellipsometric porosimetry, impedance measurements, and nanoindentation. The ease of control of the packing parameter in Gemini surfactants makes the PMO film templated by a Gemini an exciting first step towards small pore size PMO films with engineered mesostructures.

SAXS Studies of TiO2 Nanoparticles in Polymer Electrolytes and in Nanostructured Films.

Polymer electrolytes as nanostructured materials are very attractive components for batteries and opto-electronic devices. (PEO)8ZnCl2 polymer electrolytes were prepared from PEO and ZnCl2. The nanocomposites (PEO)8ZnCl2/TiO2 themselves contained TiO2 nanograins. In this work, the influence of the TiO2 nanograins on the morphology and ionic conductivity of the nanocomposite was systematically studied by transmission small-angle X-ray scattering (SAXS) simultaneously recorded with wide-angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC) at the synchrotron ELETTRA. Films containing nanosized grains of titanium dioxide (TiO2) are widely used in the research of optical and photovoltaic devices. The TiO2 films, prepared by chemical vapor deposition and e-beam epitaxy, were annealed in hydrogen atmospheres in the temperature range between 20 °C and 900 °C in order to study anatase-rutile phase transition at 740 °C. Also, grazing-incidence small angle X-ray scattering (GISAXS) spectra for each TiO2 film were measured in reflection geometry at different grazing incident angles. Environmentally friendly galvanic cells, as well as solar cells of the second generation, are to be constructed with TiO2 film as working electrode, and nanocomposite polymer as electrolyte.

Measurement method for the refractive index of thick solid and liquid layers.

A simple method is proposed for the refractive index measurement of thick solid and liquid layers. In contrast to interferometric methods, no mirrors are used, and the experimental setup is undemanding and simple. The method is based on the variation of transmission caused by optical interference within the layer as a function of incidence angle. A new equation is derived for the positions of the interference extrema versus incidence angle. Scattering at the surfaces and within the sample, as well as weak absorption, do not play important roles. The method is illustrated by the refractive index measurements of sapphire, window glass, and water.