ABSTRACT
This study analysed flexural properties, microhardness, and the degree of conversion (DC) of five bulk-fill composites under clinically relevant conditions (4 mm thick specimens) in comparison to 2 mm specimens according to ISO 4049. Additionally, the effect of rapid polymerisation on 4 mm specimens was evaluated after accelerated aging. DC was measured using Fourier transform infrared spectrometry at 2 and 4 mm thick layers, while flexural properties and Vickers microhardness were tested using 16 × 2 × 2 mm or 16 × 2 × 4 mm specimens. Three polymerisation protocols were used: (I) "ISO": 2 mm thickness, 1000 mW/cm2, double-sided; (II) "10 s": 4 mm thickness, 1000 mW/cm2, one-sided; and (III) "3 s": 4 mm thickness, 2600 mW/cm2, one-sided. Mechanical properties were tested after 1 day, after 10,000 thermocycles, and after 10,000 thermocycles followed by a 7-day immersion in absolute ethanol. The "ISO" protocol produced a higher DC and microhardness of all materials. Elastic modulus was significantly higher for the "ISO" protocol compared to the 4 mm specimens. The differences in flexural strength for all polymerisation protocols were equalised after thermocycling and immersion in absolute ethanol. All tested materials met the ISO 4049 flexural strength requirement (80 MPa) for all polymerisation methods and all aging conditions. Rapid polymerisation achieved nearly optimal properties (ISO), except for elastic modulus, which was significantly reduced in 4 mm samples.
ABSTRACT
Objectives: The aim of this study was to evaluate the retreatment duration and efficacy of eucalyptol and tea tree oil in engine driven and manual retreatment of epoxy resin based endodontic filling in extracted human teeth. Methods and materials: Sixty human single rooted teeth were randomly divided into two groups. The first group was prepared using hand files, and the second one using Reciproc system. Root canals were filled with gutta-percha points and AH Plus sealer. Retreatment was performed using K-reamers and Hedström files for the first group, and Reciproc instruments for the second group. Each group was divided into two subgroups (n=15) according to the retreatment solvent used (eucalyptol or tea tree oil). Root canals were longitudinaly split and analized with stereomicroscope (15x magnification). The surface of the remaining filling material was measured using an image processing software. Results: There were no statistically significant differences in the area of residual filling material among used solvents, nor in applied technique. Retreatment with Reciproc instruments was significantly faster compared to retreatment using hand files. The manual retreatment technique was faster when tea tree essential oil was used as a solvent compared to eucalyptol. Conclusions: Australian tea tree oil and eucalyptus oil were equally effective in removing endodontic filling material, but none of canals were completely free of the residual filling material. Retreatment with Reciproc instruments was faster compared to retreatment using hand files. The manual retreatment technique is faster when tea tree essential oil is used as a solvent compared to eucalyptol.
ABSTRACT
Objective: To compare the effectiveness of reciprocating instruments in removing gutta-percha and bioactive-based (BioRoot RCS and MTA Fillapex) and epoxy resin-based (AH Plus) sealers from root canals based on filling residues and the time required for root canal revision. Material and methods: Root canals of 90 teeth were instrumented with Reciproc R40. All root canals were obturated using the single-cone technique with Reciproc R40 gutta-percha and with one of the selected sealers. Samples with oval, straight canals were used and randomly divided into three groups: (i) filled with AH Plus sealer and gutta-percha (n=30); (ii) filled with MTA Fillapex and gutta-percha (n=30); (iii) filled with BioRoot RCS and gutta-percha (n=30). Each group was divided into two subgroups (n=15) according to the retreatment instrument used (Reciproc M-Wire R25/R40 or Reciproc blue RB25/RB40). Root canals were longitudinally split and analyzed with a stereomicroscope at 15 × magnifications in the coronal, middle, and apical third. Computational analyses were performed with the Image J software. Data were compared using the Kruskal-Wallis test and Mann-Whitney U test. Results: While no statistically significant differences in the residual material surface were found for Reciproc Blue, Reciproc M-Wire showed significantly higher residual material surface for AH Plus and MTA Fillapex compared to BioRoot RCS. For AH plus. Residual material surface was significantly lower for Reciproc Blue than for Reciproc M-Wire. In contrast, BioRoot RCS showed a significantly higher residual material surface for Reciproc Blue. Conclusions: Calcium silicate-containing sealers were more retrievable compared to AH Plus, with fewer sealer remnants and shorter retreatment time. Retreatment with Reciproc M-Wire instruments was superior to Reciproc blue instruments in retreatment of BioRoot RCS. However, none of the sealers were removed completely.
ABSTRACT
PURPOSE: To simultaneously evaluate the genotoxicity of dental composites and adhesive systems in vitro using a cytogenetic assay, with respect to the influence of composite shade. METHODS: Genotoxicity assessment was carried out in human peripheral blood leukocytes using the comet assay. Three resin composite materials, two microhybrids and one nano-hybrid, in shade A1 and A3.5 were used with manufacturer-recommended four adhesive systems. Cultures were treated for 48 hours with samples after elusion for 1 hour, 1 day, 7 days or 30 days, in two different concentrations (4.16 mg/mL, 8.33 mg/mL). Kruskall-Wallis test was used for the statistical analysis (alpha = 0.05). RESULTS: For combinations of micro-hybrid composite (A3.5) with two self-etch adhesives (16.1 +/- 5.50 and 16.2 +/- 9.52) after exposure to samples eluted for 1 day, the incidence of primary DNA damage was significantly higher than for the corresponding negative control (14.7 +/- 2.85). Genotoxicity was also higher after treatment with samples eluted for 1 hour (15.3 +/- 4.70) and 1 day (15.3 +/- 9.10), comprised of nano-hybrid composite (A1) with self-etch adhesive in relation to the control (13.1 +/- 1.70). There was no clear trend of increased DNA damage in material combinations with darker shades of composites. Material composition and higher material concentrations showed greater influence on the genotoxicity.
