ABSTRACT
This study optimized the input processing factors, namely compression force, pressing speed, heating temperature, and heating time, for extracting oil from desiccated coconut medium using a vertical compression process by applying a maximum load of 100 kN. The samples' pressing height of 100 mm was measured using a vessel chamber of diameter 60 mm with a plunger. The Box-Behnken design was used to generate the factors' combinations of 27 experimental runs with each input factor set at three levels. The response surface regression technique was used to determine the optimum input factors of the calculated responses: oil yield (%), oil expression efficiency (%), and energy (J). The optimum factors' levels were the compression force 65 kN, pressing speed 5 mm min-1, heating temperature 80 °C, and heating time 52.5 min. The predicted values of the responses were 48.48%, 78.35%, and 749.58 J. These values were validated based on additional experiments producing 48.18 ± 0.45%, 77.86 ± 0.72%, and 731.36 ± 8.04 J. The percentage error values between the experimental and the predicted values ranged from 0.82 ± 0.65 to 2.43 ± 1.07%, confirming the suitability of the established regression models for estimating the responses.
ABSTRACT
In this present study, an oil press was used to process 200 g each of sesame, pumpkin, flax, milk thistle, hemp and cumin oilseeds in order to evaluate the amount of oil yield, seedcake, sediments and material losses (oil and sediments). Sesame produced the highest oil yield at 30.60 ± 1.69%, followed by flax (27.73 ± 0.52%), hemp (20.31 ± 0.11%), milk thistle (14.46 ± 0.51%) and pumpkin (13.37 ± 0.35%). Cumin seeds produced the lowest oil yield at 3.46 ± 0.15%. The percentage of sediments in the oil, seedcake and material losses for sesame were 5.15 ± 0.09%, 60.99 ± 0.04% and 3.27 ± 1.56%. Sediments in the oil decreased over longer storage periods, thereby increasing the percentage oil yield. Pumpkin oil had the highest peroxide value at 18.45 ± 0.53 meq O2/kg oil, an acid value of 11.21 ± 0.24 mg KOH/g oil, free fatty acid content of 5.60 ± 0.12 mg KOH/g oil and iodine value of 14.49 ± 0.16 g l/100 g. The univariate ANOVA of the quality parameters against the oilseed type was statistically significant (p-value < 0.05), except for the iodine value, which was not statistically significant (p-value > 0.05). Future studies should analyze the temperature generation, oil recovery efficiency, percentage of residual oil in the seedcake and specific energy consumption of different oilseeds processed using small-large scale presses.
ABSTRACT
The present study aims to estimate the maximum oil yield of hulled sunflower seed samples in a uniaxial process under a load of 40 kN and speed of 4 mm/min. The oil samples were assessed for their quality parameters and spectra curves within the wavelength range of 325-600 nm. The results show that heating temperatures in the range of 40 °C to 80 °C increased the oil output; however, a maximum oil yield of 48.869 ± 6.023% with a minimum energy of 533.709 ± 65.644 J at the fifth repeated pressing was obtained from the unheated sample compared to the heated samples. The peroxide values ranged from 6.898 ± 0.144 to 7.290 ± 0.507 meq O2/kg, acid values from 1.043 ± 0.166 to 1.998 ± 0.276 mg KOH/g oil and free fatty acid values from 0.521 ± 0.083 to 0.999 ± 0.138 mg KOH/g oil, which were within the recommended quality threshold. There were significant spectral differences among the oil samples. A single absorbance peak was observed at 350 nm for all oil samples, indicating low levels of pigment molecules in the oil. The study revealed the need for repeated pressings to recover the considerable residual oil remaining in the seedcake after the first pressing.
ABSTRACT
The effects of different drying temperatures (50, 60, 70 °C) on the quality of rose (Rose electron) petals were evaluated in this study. Drying time decreased from 1680 s to 600 s with increased infrared temperature. The temperature and time were increased from 50 °C to 70 °C and 30 min to 60 min, respectively, and a decrease in the fruit color quality was observed. The projected area (PA) of rose petals was affected significantly from temperature. After the drying process, the largest PA was observed as 33.35 cm2 (50 °C, 30 min), while the smallest achieved at 70 °C, 60 min (27.96 cm2). Depending on the temperature values (50, 60, 70 °C), the average projection area of dry samples of the rose petals decreased 2.17 times compared to the projection area of fresh samples. The dried samples demonstrated an increase in the total phenolic (TP) content compared to the fresh samples. The maximum TP (44.49 mg GAE/g) was achieved at 45 min and 70 °C rose petals sample. The results concluded that infrared drying for 45 min at 70 °C could be recommended for drying rose (rosa electron) petals.
