Composite Si-Ni nanoparticles produced by plasma spraying physical vapor deposition for negative electrode in Li-ion batteries.

Si-Ni composite nanoparticles have been produced by a single and continuous plasma spray physical vapor deposition (PS-PVD) from Si and Ni powder feedstocks and their electrochemical performances as anode in lithium-ion batteries (LiB) are investigated. Si nanoparticles with 20-40 nm on which Ni is directly attached with Si/NiSi2epitaxial interface are formed spontaneously through co-condensation of high temperature elemental gas mixtures during PS-PVD. When only a little amount of Ni is added to Si, the effect of the epitaxial Ni attachment on the Si nanoparticles becomes evident; the cycle capacity is appreciably improved to reach a 1.6 times higher capacity than that of the Si only cell after 50 cycles, due to reduced charge-transfer resistance and nanosized Si particle. In contrast, excessive Ni addition to Si feedstock leads to formation of various silicides as a result of the accelerated silicidation during PS-PVD, which results in a significant decrease in the cycle capacity due to reduction of the active Si phase amount despite reduced charge-transfer resistance.

A case of hypereosinophilia with digital ischaemia successfully treated with intravenous prostaglandin E1.

In the therapeutic management of eosinophilic disorder, it is important to prevent hypereosinophilia (HE)-related organ damage even in the process of diagnosis. We describe here a unique clinical and histopathological findings of the patient with HE accompanied with digital ischaemia. Treatment with intravenous prostaglandin E1 was essential for digital ischaemia in our case while benralizumab, humanized monoclonal antibody against interleukin-5 receptorα, did not affect. Our case suggests an earlier intervention for digital ischaemia in the therapeutic management of eosiniphilic disorder.

Molecular analysis of the cutaneous Malassezia microbiota from the skin of patients with atopic dermatitis of different severities.

Cutaneous Malassezia is an exacerbating factor in patients with atopic dermatitis. We analysed the Malassezia microbiota of adult patients with head and neck atopic dermatitis of different severities (mild, moderate and severe). Of the nine human-associated Malassezia species, the number detected was similar (3.5-4.2 species per case) among the members of all severity groups. However, the ratio of the two major Malassezia species, M. globosa and M. restricta, was different in the severe group.

Peroral endoscopic myotomy (POEM) for esophageal achalasia.

BACKGROUND: Peroral endoscopic myotomy (POEM) was developed by our group to provide a less invasive permanent treatment for esophageal achalasia. PATIENTS AND METHODS: POEM was performed in 17 consecutive patients with achalasia (10 men, 7 women; mean age 41.4 years). A long submucosal tunnel was created (mean length 12.4 cm), followed by endoscopic myotomy of circular muscle bundles of a mean total length of 8.1 cm (6.1 cm in distal esophagus and 2.0 cm in cardia). Smooth passage of an endoscope through the gastroesophageal junction was confirmed at the end of the procedure. RESULTS: In all cases POEM significantly reduced the dysphagia symptom score (from mean 10 to 1.3; P = 0.0003) and the resting lower esophageal sphincter (LES) pressure (from mean 52.4 mmHg to 19.9 mmHg; P = 0.0001). No serious complications related to POEM were encountered. During follow-up (mean 5 months), additional treatment or medication was necessary in only one patient (case 17) who developed reflux esophagitis (Los Angeles classification B); this was well controlled with regular intake of protein pump inhibitors (PPIs). CONCLUSIONS: The short-term outcome of POEM for achalasia was excellent; further studies on long-term efficacy and on comparison of POEM with other interventional therapies are awaited.

Shrinkage dynamics of a vesicle in surfactant solutions.

We develop a theory for shrinkage dynamics of a vesicle interacting with surfactant molecules. A stepwise shrinkage is formulated in such a way that it consists of two processes. One is a nucleation process of a pore under increasing of the membrane tension. The other is a closure process of the pore due to the line tension of the pore edge after leakage of the inner fluid. We carry out numerical simulations and show that the results agree with experiments semi-quantitatively. An analytical study is also carried out to understand the periodic shrinkage.

Endoscopic in vivo evaluation of tissue atypia in the esophagus using a newly designed integrated endocytoscope: a pilot trial.

BACKGROUND AND STUDY AIMS: A newly designed magnifying endoscope featuring an endocytoscopy function provided by ultrahigh magnification was evaluated in a pilot study in patients with various types of benign and malignant pathology in the esophagus. PATIENTS AND METHODS: Seventy-five consecutive patients were included in the study from 15 March to 21 December 2005. Twenty-nine patients with specific esophageal lesions that had been detected by regular or narrow-band imaging, or both, were further evaluated using endocytoscopy, followed by tissue biopsy or resection. During the endocytoscopic examinations, the esophageal mucosa was stained with 0.5 % methylene blue. The endocytoscopic findings were graded from 1 to 5 in an endocytoscopic atypia (ECA) classification. The final histopathological diagnoses based on biopsies or resected specimens were as follows: category 1 in the Vienna classification, n = 4; category 2, n = 6; category 3, n = 1; category 4, n = 10; and category 5, n = 7. The endocytoscopic diagnoses were compared with the histopathological diagnoses. RESULTS: Clear endocytoscopic images were obtained in all cases. In definitely malignant lesions, the cell nuclei had an enlarged and irregularly arranged appearance (grade ECA 5). The positive predictive value for malignancy (grades ECA 4 and 5) was 94 %; the false-negative rate was 16.7 %, and the false-positive rate was 6.3 %. The overall accuracy of endocytoscopy for differentiating between nonmalignant tissue (categories 1 - 3 in the Vienna classification) and malignant tissue (categories 4 and 5) was 82 %. CONCLUSIONS: These preliminary results suggest that incorporating endocytoscopy facilities into a standard endoscope may be helpful in characterizing tissue in a variety of esophageal lesions. The potential clinical impact of this method in relation to other gastrointestinal organs requires further study.

Contraction stress in dentin adhesives bonded to dentin.

Adhesives cured under constrained conditions develop contraction stresses. We hypothesized that, with dentin as a bonding substrate, the stress would reach a maximum, followed by a continuous decline. Stress development was determined with a tensilometer for two total-etch systems and two systems with self-etching primers. The adhesives were placed in a thin layer between a glass plate and a flat dentin surface pretreated with phosphoric acid or self-etching primer. After an initial maximum shortly after light-curing, the stress decreased dramatically for the total-etch systems (70%) and, to a lesser extent, for the adhesives with self-etching primers (30%). The greater stress decrease for the total-etch systems was ascribed to water and/or solvents released into the adhesives from the fully opened dentinal tubules by the pulling/sucking action of the contraction stress. This happened less with the adhesives with self-etching primers, where the tubules remained mainly closed.

Dental adhesive compounds alter glutathione levels but not glutathione redox balance in human THP-1 monocytic cells.

The use of hydrophilic dental monomers in dentin bonding agents has vastly improved resin-dentin bond strengths, but incomplete polymerization of these monomers and their leaching into adjacent (pulpal) oral tissues has raised concerns about their biocompatibility. The sublethal effects of these resins are virtually unknown, but their electrophilic nature led to the hypothesis that they may alter cellular oxidative stress pathways. Glutathione balance between reduced (GSH) and oxidized (GSSG) is a major mechanism by which cells maintain redox balance and was therefore the focus of the current investigation. THP-1 human monocytic cells were exposed to hydroxyethyl methacrylate (HEMA), benzoyl peroxide (BPO), camphorquinone (CQ), or triethyelene glycol dimethacrylate (TEGDMA) for 24 h at sublethal doses, then GSH and GSSG levels were measured by means of Ellman's method adapted for cell culture. The results indicate that these dental resin compounds act at least partly via oxidative stress by increasing GSH levels at sublethal concentrations. However, the GSH-GSSG ratio was relatively unaffected. Only BPO altered the GSH-GSSG ratio at 24 h, again at sublethal levels (7.5-15 micromol/L). The results support the hypothesis that resin monomers act, at least in part, via oxidative stress, and that oxidative-stress pathways should be one focus of future investigations of monomer biocompatibility.

Fluid movement across the resin-dentin interface during and after bonding.

This study evaluated the extent of water penetration through resin-dentin interfaces before and after being sealed with adhesives. Four adhesive resin systems (2 total-etch adhesives and 2 self-etching primer adhesives) were used in this study. Dentin disks were placed in a split-chamber device, and in situ fluid movement across dentin was measured, with and without physiological pressure, during bonding procedures or 24 hrs after bonding. The fluid movement across dentin occurs via dentin tubules after acid-etching. Large outward or inward fluid shifts across dentin were observed during air-drying and light-curing for resin application. The amount of fluid movement across resin-bonded dentin when total-etch adhesives were used was significantly greater than that with self-etching adhesives. The milder acid-etching effects of self-etching primers may retain hybridized smear plugs within the tubules that reduce outward fluid flow, resulting in superior dentin sealing.

In vitro effect of nanoleakage expression on resin-dentin bond strengths analyzed by microtensile bond test, SEM/EDX and TEM.

This study evaluated the effect of multiple consecutive adhesive resin coatings of adhesive bonded to human dentin on nanoleakage and resin-dentin bond strength. Resin bonded dentin specimens were prepared using a total-etch adhesive (One-Step Plus) applied as multiple consecutive coating, or using two self-etch adhesive systems (iBond or Fluoro Bond). For the total-etch adhesive, resin application and air evaporation were performed 1, 2, 3, or 4 times. The self-etch adhesives were applied according to manufacturers' instructions. Resin-dentin bonded beams were prepared and immersed in water (control) or ammoniacal silver nitrate. After storage, microtensile bond strengths were measured. The fractured surfaces were examined by scanning and transmission electron microscopy (SEM and TEM), and energy-dispersive X-ray spectrometry (EDX). No significant differences in bond strength were found between water and silver nitrate storage groups. Several types of silver depositions (spotted, reticular, or water trees) were found in adhesive joints. The bond strengths of the single coated specimens of the total-etch adhesive were significantly lower than those receiving 2-4 coatings. Single coats produced more nanoleakage than multiple coats. However, no correlation was found between the bond strengths and nanoleakage between the different adhesives (total-etch adhesive with different conditions or self-etch adhesives).

Degradation of resin-dentin bonds using NaOCl storage.

OBJECTIVE: Several recent studies have reported collagen hydrolysis within bonds over the long-term. This may be one reason for the degradation of the bonds. This study therefore aimed to determine the effects of NaOCl on adhesive system bonds (total-etch bonding system vs. self-etching primer system) to dentin in order to accelerate the durability testing. METHODS: Resin-dentin bonded specimens were produced using Liner Bond 2V (Kuraray), a self-etching primer system, and OptiBond SOLO (Kerr), a total-etch bonding system, according to the manufacturers' instructions. The bonded specimens were serially sectioned in both x and y directions across the adhesive interface to obtain beams (adhesive area: 0.9 mm(2)). The specimens were immersed in 10% NaOCl solution for 1-5h after being stored in water at 37 degrees C for 24h. Control specimens were tested without exposure to NaOCl. After storage, micro-tensile bond tests were performed. Results were analyzed by two-way ANOVA and Fisher's PLSD tests (p<0.05). All fractured surfaces were observed by SEM, and examined using an image analyzer. RESULTS: The bond strengths decreased with increasing storage time in NaOCl. Fractography showed that NaOCl had a greater effect on the bond structure of OptiBond SOLO than on that of Liner Bond 2V, although both adhesives were susceptible. SIGNIFICANCE: Deterioration of the bonds was responsible for the effect of NaOCl on the hybrid layer. This deterioration may occur in humans in cases of deproteinization within the bonds.

Over-etching effects on micro-tensile bond strength and failure patterns for two dentin bonding systems.

OBJECTIVES: The purpose of this study was to determine (1) the weakest zone of resin-dentin bonds and (2) the relation between bond strength and failure mode to clarify the effect of demineralized dentin. METHODS: Human premolars were sectioned to expose the dentin surfaces, and the dentin surfaces were conditioned with phosphoric acid for 15, 60, 120, or 180s. Resin-dentin bonded specimens were produced using two adhesives: One-Step (Bisco) and OptiBond Solo (Kerr). Each sample was sectioned to produce a beam (adhesive area: 0.9mm(2)). Microtensile bond tests were then conducted, and the mean bond strengths (n=12 for each group) were statistically compared using two-way ANOVA and Duncan's multiple-range test (p<0.05). The fractured surfaces of all specimens were examined using SEM, and the areas of failure were measured using an image analyzer. RESULTS: For One-Step, the bond strength decreased with increase in acid-conditioning time (15s: 50.7+/-9.7, 60s: 40.8+/-11.0, 120s: 23.6+/-4.9 and 180s: 12.1+/-4.6MPa) (p<0.05). For OptiBond Solo, the bond strength in the case of 15s acid-conditioning time (42.6+/-7.9MPa) was significantly greater than that for the other times (60s: 31.9+/-10.3, 120s: 31.8+/-14.4 and 180s: 31.8+/-7.4MPa) (p<0.05). Fractography showed that the area percentage of the hybrid layer increased with increase in etching time for both systems. CONCLUSIONS: The integrity of the hybrid layer, especially the top part, has an effect on bond strength.

Low-dose, long-term exposures of dental material components alter human monocyte metabolism.

The short-term degradation of dental polymers and alloys in biological environments has been well documented, but recent evidence indicates that oral tissues may be chronically exposed to low levels of these released components. The effect of these chronic exposures on the ability of cells to respond to a subsequent challenge is not known. To investigate this idea, we exposed human THP-1 monocytes to sublethal concentrations of HEMA, TEGDMA, Hg(2+), and Ni(2+) for 2 weeks and then assessed the monocytic response to subsequent 24-h challenge with the same components at higher concentrations. Chronic (2 week) exposures of monocytes to HEMA and both metal ions significantly altered monocyte response to short-term (24 h) secondary exposures, even when overt effects of the chronic exposures were not apparent. However, cellular responses were highly variable depending on the material and its concentrations. For TEGDMA, no effects were seen. These results demonstrate that the chronic effects of materials must be considered even when the chronic exposure has no initial overt effect. The effect on cells may only be apparent if the cell is challenged by a secondary exposure.

Components of dentinal adhesives modulate heat shock protein 72 expression in heat-stressed THP-1 human monocytes at sublethal concentrations.

Few studies have investigated the ability of dental resins to induce cellular stress at sublethal concentrations. Cellular stress, especially in immune cells such as monocytes, may modulate the biological response to materials or the host's ability to respond to bacterially mediated inflammation. The current study examined the ability of sublethal concentrations of 2-hydroxylethylmethacrylate (HEMA) and triethyleneglycol dimethacrylate (TEGDMA) to induce heat shock protein 72 (HSP72) in human monocytes. HEMA and TEGDMA significantly suppressed heat-induced HSP72 expression, even at sublethal levels, but did not induce HSP72 by themselves. The results of the current study suggest that components released from dental resin could modulate the HSP stress response without altering cellular metabolic activity.

The extent to which resin can infiltrate dentin by acetone-based adhesives.

The combined methodologies of fractography and laser-Raman spectroscopic analysis were used for evaluation of the resin-dentin bonds made with wet and dry bonding. Resin-dentin-bonded beams were produced by means of 2 acetone-based adhesives (One-Step and Prime & Bond NT). The micro-tensile bond test was conducted, and the fractured surfaces of all specimens were examined by SEM and an image analyzer. The amount of resin infiltration within the hybrid layer was quantified by means of a laser-Raman spectroscope. In Raman analysis, the amount of resin impregnation within the hybrid layer of the dry bonding was found to be significantly lower (approximately 50%) than that in the wet one. Under fractographic analysis, a correlation was found between the bond strength and the failure mode. Based on those findings, it was suggested that the integrity between the bonding resin and the top of the hybrid layer played a major role in bond strength.

Delayed eruption of premolars with periodontitis of primary predecessors and a cystic lesion: a case report.

Apical periodontitis after pulp therapy in a primary tooth can cause delayed eruption of the permanent successor. A case of bilateral delayed eruption of mandibular premolars is presented. The patient. a 13-year-old girl, was referred by her dentist. Oral findings showed that the right first and left second primary molars were retained. Other premolars had erupted. An orthopantomogram revealed apical periodontitis, affecting both retained primary molars. The right first mandibular premolar was impacted against the alveolar bone and root of the second premolar, and there was a large cystic lesion in close association with the left second mandibular premolar. Both primary molars were extracted, and the cystic lesion was treated by marsupialization. Fenestration and traction were performed on the right first premolar. Correct tooth alignment was achieved with orthodontic appliances. If the problem had been detected earlier, treatment of the premolars might have been easier. Clinical and radiological follow-up, therefore, of primary teeth that have undergone pulp therapy procedures should be performed until eruption of succedaneous teeth.