Alkali-resistant low-temperature atomic-layer-deposited oxides for optical fiber sensor overlays.

This paper presents an investigation of properties of selected metallic oxides deposited at a low temperature (100 °C) by atomic layer deposition (ALD) technique, relating to their applicability as thin overlays for optical fiber sensors resistant in alkaline environments. Hafnium oxide (Hf x O y with y/x approx. 2.70), tantalum oxide (Ta x O y with y/x approx. 2.75) and zirconium oxide (Zr x O y with y/x approx. 2.07), which deposition was based, respectively, on tetrakis(ethylmethyl)hafnium, tantalum pentachloride and tetrakis(ethylmethyl)zirconium with deionized water, were tested as thin layers on planar Si (100) and glass substrates. Growth per cycle (GPC) in the ALD processes was 0.133-0.150 nm/cycle. Run-to-run GPC reproducibility of the ALD processes was best for Hf x O y (0.145 ± 0.001 nm/cycle) and the poorest for Ta x O y (0.133 ± 0.003 nm/cycle). Refractive indices n of the layers were 2.00-2.10 (at the wavelength λ = 632 nm), with negligible k value (at λ for 240-930 nm). The oxides examined by x-ray diffractometry proved to be amorphous, with only small addition of crystalline phases for the Zr x O y . The surfaces of the oxides had grainy but smooth topographies with root-mean square roughness ∼0.5 nm (at 10 × 10 µm2 area) according to atomic force microscopy. Ellipsometric measurements, by contrast, suggest rougher surfaces for the Zr x O y layers. The surfaces were also slightly rougher on the glass-based samples than on the Si-based ones. Nanohardness and Young modules were 4.90-8.64 GPa and 83.7-104.4 GPa, respectively. The tests of scratch resistance revealed better tribological properties for the Hf x O y and the Ta x O y than for the Zr x O y . The surfaces were hydrophilic, with wetting angles of 52.5°-62.9°. The planar oxides on Si, being resistive even to concentrated alkali (pH 14), proved to be significantly more alkali-resistive than Al2O3. The Ta x O y overlay was deposited on long-period grating sensor induced in optical fiber. Thanks to such an overlay the sensor proved to be long-lasting resistant when exposed to alkaline environment with a pH 9. Thereby, it also proved that it has a potential to be repeatedly reused as a regenerable optical fiber biosensor.

The effect of CART on pituitary hormones release from cultured pituitary cells harvested from fasted and fed ad libitum male rats.

Cocaine and Amphetamine-Regulated Transcript (CART) is widely expressed in the central nervous system and in several endocrine organs. CART is an important factor in the regulation of energy homeostasis. The aim of the study was to assess the role of CART in physiological response of pituitary cells in a course of starvation. The pituitary cells harvested from starved and fed ad libitum male rats were cultured for 48h and treated with: 0.1nM, 1nM, 10nM or 100nM doses of CART. The medium was collected after 60min and stored at -70°C until samples were further assayed for: LH, FSH, PRL, GH, TSH and ACTH. We revealed that in cultures of pituitary cells collected from fasted rats the basal levels of the examined hormones were reduced. Incubation of pituitary cells of non-starved rats with any dose of CART reduced the concentration of LH and TSH, while the levels of the other hormones were decreased after administration only specific doses of CART. In cells of fasted rats no change in the concentration of gonadotrophins was observed. The PRL level was increased only in the 1nM dose of CART, while the 10nM and 100nM CART doses markedly enhanced GH and TSH. Moreover, administration of 1nM, 10nM and 100nM of CART to cultured cells of fasted rats resulted in a significant rise of the ACTH. Our results indicate that CART can directly affect the physiological release of PRL, ACTH, TSH and GH in pituitary cells of starved animals. Moreover, CART did not alter the LH and FSH suppression level, which is correlated with food deprivation. This data stays in contrast with the already proposed role of CART as an anorexigenic hypothalamic factor.

Influence of Cu, Au and Ag on structural and surface properties of bioactive coatings based on titanium.

In this work influence of copper, silver and gold additives on structural and surface properties of biologically active thin films based on titanium have been described. Coatings were prepared by magnetron sputtering method. During each process metallic discs (targets) - Ti and the additive (Cu, Ag or Au) were co-sputtered in argon atmosphere. Structural investigation of as-deposited coatings was performed with the aid of XRD and SEM/EDS method. It was found that all prepared thin films were homogenous. Addition of Cu, Ag and Au resulted in nanocrystalline structure. Moreover, influence of these additives on hardness and antibacterial activity of titanium coatings was also studied. Ti-Cu, Ti-Ag and Ti-Au films had lower hardness as-compared to Ti. According to AAS results the difference of their activity was related to the ion migration process. It was found that Ti-Ag and Ti-Au coatings had biocidal effect related to direct contact of their surface with microorganisms. In the case of Ti-Cu antimicrobial activity had direct and indirect nature due to efficient ion migration process from the film surface to the surrounding environment. Functional features of coatings such as wettability and corrosion resistance were also examined and included in the comprehensive analysis.

Total and high molecular weight adiponectin levels in the rat model of post-myocardial infarction heart failure.

Adiponectin is a protein secreted primarily by adipose tissue. It has been suggested that adiponectin plays a protective role in the early phase following myocardial infarction. Our primary aim was to investigate the effects of post-myocardial infarction heart failure well-characterized by left ventricular hemodynamic parameters on the total and high molecular weight adiponectin concentrations in plasma, fat and cardiac tissue. Eight weeks after myocardial infarction or sham operation, total and high molecular weight adiponectin concentrations in plasma, fat, and cardiac tissues were assayed in rats. In addition, hemodynamic parameters and expression of the genes encoding atrial natriuretic peptide and brain natriuretic peptide in left ventricle were evaluated. Atrial natriuretic peptide and brain natriuretic peptide mRNA levels in left ventricle tissue were higher in rats with myocardial infarction-induced heart failure compared with the controls. Similarly, total adiponectin concentration was increased in left ventricle (but not in right ventricle) in rats with post-myocardial infarction heart failure. In contrast, adiponectin levels in plasma and cardiac adipose tissue in rats with post-myocardial infarction heart failure were lower than in sham-operated animals. Furthermore, there were no significant differences in levels of high molecular weight adiponectin in plasma, cardiac tissue or adipose tissue between these two groups. We conclude that in the rat model of post-myocardial infarction heart failure, adiponectin level is increased in left ventricle tissue. This is accompanied by decreased adiponectin levels in plasma and cardiac adipose tissue.

Determination of structural, mechanical and corrosion properties of Nb2O5 and (NbyCu 1-y)Ox thin films deposited on Ti6Al4V alloy substrates for dental implant applications.

In this paper comparative studies on the structural, mechanical and corrosion properties of Nb2O5/Ti and (NbyCu1-y)Ox/Ti alloy systems have been investigated. Pure layers of niobia and niobia with a copper addition were deposited on a Ti6Al4V titanium alloy surface using the magnetron sputtering method. The physicochemical properties of the prepared thin films were examined with the aid of XRD, XPS SEM and AFM measurements. The mechanical properties (i.e., nanohardness, Young's modulus and abrasion resistance) were performed using nanoindentation and a steel wool test. The corrosion properties of the coatings were determined by analysis of the voltammetric curves. The deposited coatings were crack free, exhibited good adherence to the substrate, no discontinuity of the thin film was observed and the surface morphology was homogeneous. The hardness of pure niobium pentoxide was ca. 8.64GPa. The obtained results showed that the addition of copper into pure niobia resulted in the preparation of a layer with a lower hardness of ca. 7.79 GPa (for niobia with 17 at.% Cu) and 7.75 GPa (for niobia with 25 at.% Cu). The corrosion properties of the tested thin films deposited on the surface of titanium alloy depended on the composition of the thin layer. The addition of copper (i.e. a noble metal) to Nb2O5 film increased the corrosion resistance followed by a significant decrease in the value of corrosion currents and, in case of the highest Cu content, the shift of corrosion potential towards the noble direction. The best corrosion properties were obtained from a sample of Ti6Al4V coated with (Nb0.75Cu0.25)Ox thin film. It seems that the tested materials could be used in the future as protection coatings for Ti alloys in biomedical applications such as implants.

Effect of orexin A on the release of GnRH-stimulated gonadotrophins from cultured pituitary cells of immature and mature female rats.

Orexin A (OxA), also known as hypocretin 1, is a regulatory neuropeptide involved in the control of various autonomic and neuroendocrine functions. It appears to have a significant impact on the regulation of trophic hormones secretion by influencing the hypothalamus and the pituitary. Orexin A acts through two types of receptor found in the pituitary. This suggests the possibility of direct action of OxA at the adenohypophysis level. The aim of this study was to investigate the direct effect of OxA on GnRH (gonadotrophin-releasing hormone)-stimulated LH and FSH secretion from cultured pituitary cells of sexually immature and mature female rats. Anterior pituitary cells obtained from immature and mature female rats (ovariectomized, and ovariectomized and treated with estradiol) were incubated with 10(-10)M or 10(-7)M orexin A for 1 hour and 4h and the effect on GnRH-stimulated (10(-9)M or 10(-6)M) LH and FSH release was examined. The concentrations of secreted gonadotrophins in the culture media were determined by RIA methods. Orexin A significantly inhibited GnRH-stimulated FSH release from pituitary cells isolated from immature female rats, whereas in cells of mature ovariectomized animals, the effect of OxA was dependent on the stimulatory dose of GnRH. When the cells were stimulated with a low dose of GnRH, orexin A inhibited the secretion of gonadotrophins, but when a high dose of GnRH was used, orexin A increased mainly the release of LH. In cultured pituitary cells from ovariectomized, estrogenized mature rats, orexin A inhibited the secretion of LH if the cells were stimulated with a high dose of GnRH. In conclusion, the results of this study revealed that orexin A may modify the sensitivity of gonadotrophic cells to GnRH, and its effect depends on the maturity and estrogen status of the rats from which the cells are isolated.

Global gene expression analysis in fetal mouse ovaries with and without meiosis and comparison of selected genes with meiosis in the testis.

In order to identify novel genes involved in early meiosis and early ovarian development in the mouse, we used microarray technology to compare transcriptional activity in ovaries without meiotic germ cells at embryonic age 11.5 (E11.5) and E13.5 ovaries with meiosis. Overall, 182 genes were differentially expressed; 134 were known genes and 48 were functionally uncharacterized. A comparison of our data with the literature associated, for the first time, at least eight of the known genes with female meiosis/germ cell differentiation (Aldh1a1, C2pa, Tex12, Stk31, Lig3, Id4, Recql, Piwil2). These genes had previously only been described in spermatogenesis. The microarray also detected an abundance of vesicle-related genes of which four were upregulated (Syngr2, Stxbp1, Ric-8, SytIX) and one (Myo1c) was downregulated in E13.5 ovaries. Detailed analysis showed that the temporal expression of SytIX also coincided with the first meiotic wave in the pubertal testis. This is the first time that SytIX has been reported in non-neuronal tissue. Finally, we examined the expression of one of the uncharacterized genes and found it to be gonad-specific in adulthood. We named this novel transcript "Gonad-expressed transcript 1" (Get-1). In situ hybridization showed that Get-1 was expressed in meiotic germ cells in both fetal ovaries and mature testis. Get-1 is therefore a novel gene in both male and female meiosis.

Recombinant tyrosine aminotransferase from Trypanosoma cruzi: structural characterization and site directed mutagenesis of a broad substrate specificity enzyme.

The gene encoding tyrosine aminotransferase (TAT, EC 2.6.1.5) from the parasitic protozoan Trypanosoma cruzi was amplified from genomic DNA, cloned into the pET24a expression vector and functionally expressed as a C-terminally His-tagged protein in Escherichia coli BL21(DE3)pLysS. Purified recombinant TAT exhibited identical electrophoretic and enzymatic properties as the authentic enzyme from T. cruzi. Both recombinant and authentic T. cruzi TATs were highly resistant to limited tryptic cleavage and contained no disulfide bonds. Comprehensive analysis of its substrate specificity demonstrated TAT to be a broad substrate aminotransferase, with leucine, methionine as well as tyrosine, phenylalanine, tryptophan and alanine being utilized efficiently as amino donors. Valine, isoleucine and dicarboxylic amino acids served as poor substrates while polar aliphatic amino acids could not be transaminated. TAT also accepted several 2-oxoacids, including 2-oxoisocaproate and 2-oxomethiobutyrate, in addition to pyruvate, oxaloacetate and 2-oxoglutarate. The functionality of the expression system was confirmed by constructing two variants; one (Arg389) being a completely inactive enzyme; the other (Arg283) retaining its full activity, as predicted from the recently solved three-dimensional structure of T. cruzi TAT. Thus, only one of the two strictly conserved arginines which are essential for the enzymatic activity of subfamily Ialpha aspartate and aromatic aminotransferases is critical for T. cruzi's TAT activity.

Crystal structure of Trypanosoma cruzi tyrosine aminotransferase: substrate specificity is influenced by cofactor binding mode.

The crystal structure of tyrosine aminotransferase (TAT) from the parasitic protozoan Trypanosoma cruzi, which belongs to the aminotransferase subfamily Igamma, has been determined at 2.5 A resolution with the R-value R = 15.1%. T. cruzi TAT shares less than 15% sequence identity with aminotransferases of subfamily Ialpha but shows only two larger topological differences to the aspartate aminotransferases (AspATs). First, TAT contains a loop protruding from the enzyme surface in the larger cofactor-binding domain, where the AspATs have a kinked alpha-helix. Second, in the smaller substrate-binding domain, TAT has a four-stranded antiparallel beta-sheet instead of the two-stranded beta-sheet in the AspATs. The position of the aromatic ring of the pyridoxal-5'-phosphate cofactor is very similar to the AspATs but the phosphate group, in contrast, is closer to the substrate-binding site with one of its oxygen atoms pointing toward the substrate. Differences in substrate specificities of T. cruzi TAT and subfamily Ialpha aminotransferases can be attributed by modeling of substrate complexes mainly to this different position of the cofactor-phosphate group. Absence of the arginine, which in the AspATs fixes the substrate side-chain carboxylate group by a salt bridge, contributes to the inability of T. cruzi TAT to transaminate acidic amino acids. The preference of TAT for tyrosine is probably related to the ability of Asn17 in TAT to form a hydrogen bond to the tyrosine side-chain hydroxyl group.