High performance of low band gap polymer-based ambipolar transistor using single-layer graphene electrodes.

Bottom-contact bottom-gate organic field-effect transistors (OFETs) are fabricated using a low band gap pDTTDPP-DT polymer as a channel material and single-layer graphene (SLG) or Au source/drain electrodes. The SLG-based ambipolar OFETs significantly outperform the Au-based ambipolar OFETs, and thermal annealing effectively improves the carrier mobilities of the pDTTDPP-DT films. The difference is attributed to the following facts: (i) the thermally annealed pDTTDPP-DT chains on the SLG assume more crystalline features with an edge-on orientation as compared to the polymer chains on the Au, (ii) the morphological features of the thermally annealed pDTTDPP-DT films on the SLG electrodes are closer to the features of those on the gate dielectric layer, and (iii) the SLG electrode provides a flatter, more hydrophobic surface that is favorable for the polymer crystallization than the Au. In addition, the preferred carrier transport in each electrode-based OFET is associated with the HOMO/LUMO alignment relative to the Fermi level of the employed electrode. All of these experimental results consistently explain why the carrier mobilities of the SLG-based OFET are more than 10 times higher than those of the Au-based OTFT. This work demonstrates the strong dependence of ambipolar carrier transport on the source/drain electrode and annealing temperature.

Tailoring dispersion and aggregation of Au nanoparticles in the BHJ layer of polymer solar cells: plasmon effects versus electrical effects.

Plasmonic effects that arise from embedding metallic nanoparticles (NPs) in polymer solar cells (PSCs) have been extensively studied. Many researchers have utilized metallic NPs in PSCs by either incorporating them into the PSC interlayers (e.g., the hole extraction and electron extraction layers) or blending them into the bulk heterojunction (BHJ) active layer. In such studies, the dispersity of the metallic NPs in each layer may vary due to both the different nature of the ligands and the amount of ligands on the metallic NPs. This in turn can produce different PSC performance parameters. Here, we systematically control the amount of attached organic ligands on Au NPs to control their dispersion behavior in the BHJ active layer of PSCs. By controlling the number of capping organic ligands on the Au NPs, the dispersity of the NPs in the BHJ layer is also controlled and the positive effects (particularly the plasmonic and electrical effects) of the Au NPs in the PSCs are investigated. From the obtained results, we find that the electrical contribution of the Au NPs is a more dominant factor for enhancing cell efficiency when compared to the plasmonic effect.

Micropatterned single-walled carbon nanotube electrodes for use in high-performance transistors and inverters.

We demonstrated the solution-processed single-walled carbon nanotube (SWNT) source-drain electrodes patterned using a plasma-enhanced detachment patterning method for high-performance organic transistors and inverters. The high-resolution SWNT electrode patterning began with the formation of highly uniform SWNT thin films on a hydrophobic silanized substrate. The SWNT source-drain patterns were then formed by modulating the interfacial energies of the prepatterned elastomeric mold and the SWNT thin film using oxygen plasma. The SWNT films were subsequently selectively delaminated using a rubber mold. The patterned SWNTs could be used as the source-drain electrodes for both n-type PTCDI-C8 and p-type pentacene field-effect transistors (FETs). The n- and p-type devices exhibited good and exactly matched electrical performances, with a field-effect mobility of around 0.15 cm(2) V(-1) s(-1) and an ON/OFF current ratio exceeding 10(6). The single electrode material was used for both the n and p channels, permitting the successful fabrication of a high-performance complementary inverter by connecting a p-type pentacene FET to an n-type PTCDI-C8 FET. This patterning technique was simple, inexpensive, and easily scaled for the preparation of large-area electrode micropatterns for flexible microelectronic device fabrication.

High crystalline dithienosilole-cored small molecule semiconductor for ambipolar transistor and nonvolatile memory.

We characterized the electrical properties of a field-effect transistor (FET) and a nonvolatile memory device based on a solution-processable low bandgap small molecule, Si1TDPP-EE-C6. The small molecule consisted of electron-rich thiophene-dithienosilole-thiophene (Si1T) units and electron-deficient diketopyrrolopyrrole (DPP) units. The as-spun Si1TDPP-EE-C6 FET device exhibited ambipolar transport properties with a hole mobility of 7.3×10(-5) cm2/(Vs) and an electron mobility of 1.6×10(-5) cm2/(Vs). Thermal annealing at 110 °C led to a significant increase in carrier mobility, with hole and electron mobilities of 3.7×10(-3) and 5.1×10(-4) cm2/(Vs), respectively. This improvement is strongly correlated with the increased film crystallinity and reduced π-π intermolecular stacking distance upon thermal annealing, revealed by grazing incidence X-ray diffraction (GIXD) and atomic force microscopy (AFM) measurements. In addition, nonvolatile memory devices based on Si1TDPP-EE-C6 were successfully fabricated by incorporating Au nanoparticles (AuNPs) as charge trapping sites at the interface between the silicon oxide (SiO2) and cross-linked poly(4-vinylphenol) (cPVP) dielectrics. The device exhibited reliable nonvolatile memory characteristics, including a wide memory window of 98 V, a high on/off-current ratio of 1×10(3), and good electrical reliability. Overall, we demonstrate that donor-acceptor-type small molecules are a potentially important class of materials for ambipolar FETs and nonvolatile memory applications.