ABSTRACT
Objectives: The aim of this retrospective study was to analyze the occurrence and characteristics of pre-eruptive intracoronal resorptions in a clinical orthodontic patient population. Materials and methods: Patients treated in an orthodontic department (University of Pécs, Pécs, Hungary) were included. Unerupted teeth on panoramic radiographs were analyzed for intracoronal radiolucent lesions. For each patient, the demographic data, jaw localization, number of unerupted teeth with pre-eruptive intracoronal resorption lesions, number of lesions per tooth, size and localization of pre-eruptive intracoronal resorption defects, affected tooth's surface, pulp involvement and ectopic position of the tooth with defects were recorded. Results: In the 3,143 patients investigated, 55 teeth in 49 patients showed pre-eruptive intracoronal resorption lesions (subject incidence: 1.56%). The incidence on unerupted teeth was 0.25%. Pre-eruptive intracoronal resorption was significantly more common in mandibles (43 mandibular vs. 12 maxillary lesions) with an odds ratio of 12.84 (95% Confidence Interval: 5.19-31.74) and no gender differences were found (p = 0.746). The occurrence of pre-eruptive intracoronal resorption was highest in the youngest (7-10 years) mixed dentition status group (p < 0.001). Most of the lesions (44 of 55, or 80.0%) were localized in the dentin, occupying two-third or less of the dentin thickness. Only 12.73% (7/55) of the lesions were not localized on the occlusal surface. Of the lesions, 89.1% (49/55) showed no obvious size increase over an average follow-up of 36.4 ± 8.1 months. Conclusions: Pre-eruptive intracoronal resorption may occur mainly in the mixed dentition stage in orthodontic patients. Careful and attentive radiographic evaluations may facilitate early detection and follow-up of the lesions' possible dimensional changes, especially when resorption influences orthodontic extraction therapy.
ABSTRACT
Class II malocclusion is one of the most common dental anomalies and the use of intermaxillary elastomers is the standard method in its treatment. However, orthodontic elastics cannot exert continuous force over a period of time due to force degradation. Our goal was to mechanically characterize the different types of elastomers during static and cyclic loads, based on uniform methodology and examine the morphological changes after loading. Ten types of latex-containing and four latex-free intermaxillary elastics were examined from six different manufacturers. To determine the mechanical characteristics of the elastomers, tensile tests, cyclical tensile fatigue tests and 24 h relaxation tests were performed, and the elastics were also subjected to scanning electron microscopy (SEM) and Raman spectroscopy. Regardless of the manufacturer, the latex-containing elastomers did not show significant differences in the percentage of elongation at break during the tensile test. Only one type of latex-containing elastomer did not tear during the 24 h cyclical fatigue test. Fatigue was confirmed by electron microscopy images, and the pulling force reduced significantly. During the force relaxation test, only one latex-free ligature was torn; the force degradation was between 7.8% and 20.3% for latex ligatures and between 29.6% and 40.1% for latex-free elastomers. The results showed that dynamic loading was more damaging to ligatures than static loading, latex-containing elastomers were more resistant than latex-free elastics, and which observation could have clinical consequences or a potential effect on patient outcome.
ABSTRACT
Bone fractures pose a serious challenge for the healthcare system worldwide. A total of 17.5% of these fractures occur in the distal radius. Traditional cast materials commonly used for treatment have certain disadvantages, including a lack of mechanical and water resistance, poor hygiene, and odors. Three-dimensional printing is a dynamically developing technology which can potentially replace the traditional casts. The aim of the study was to examine and compare the traditional materials (plaster cast and fiberglass cast) with Polylactic Acid (PLA) and PLA-CaCO3 composite materials printed using Fused Filament Fabrication (FFF) technology and to produce a usable cast of each material. The materials were characterized by tensile, flexural, Charpy impact, Shore D hardness, flexural fatigue, and variable load cyclic tests, as well as an absorbed water test. In addition, cost-effectiveness was evaluated and compared. The measured values for tensile strength and flexural strength decreased with the increase in CaCO3 concentration. In the fatigue tests, the plaster cast and the fiberglass cast did not show normal fatigue curves; only the 3D-printed materials did so. Variable load cyclic tests showed that traditional casts cannot hold the same load at the same deflection after a higher load has been used. During these tests, the plaster cast had the biggest relative change (-79.7%), compared with -4.8 % for the 3D-printed materials. The results clearly showed that 3D-printed materials perform better in both static and dynamic mechanical tests; therefore, 3D printing could be a good alternative to customized splints and casts in the near future.
