ABSTRACT
The need to identify secondary sources of REEs and their recovery has led to the search for new methods and materials. In this study, a novel type of ion-imprinted adsorption membranes based on modified chitosan was synthesized. Their application for the recovery of chosen REEs from synthetic coal fly ash extracts was analyzed. The examined membranes were analyzed in terms of adsorption kinetics, isotherms, selectivity, reuse, and their separation abilities. The experimental data obtained were analyzed with two applications, namely, REE 2.0 and REE_isotherm. It was found that the adsorption of Nd3+ and Y3+ ions in the obtained membranes took place according to the chemisorption mechanism and was significantly controlled by film diffusion. The binding sites on the adsorbent surface were uniformly distributed; the examined ions showed the features of regular monolayer adsorption; and the adsorbents showed a strong affinity to the REE ions. The high values of Kd (900-1472.8 mL/g) demonstrate their high efficiency in the recovery of REEs. After five subsequent adsorption-desorption processes, approximately 85% of the value of one cycle was reached. The synthesized membranes showed a high rejection of the matrix components (Na, Mg, Ca, Al, Fe, and Si) in the extracts of the coal fly ashes, and the retention ratio for these Nd and Y ions was 90.11% and 80.95%, respectively.
ABSTRACT
This work focuses on the production of gradient composite materials with an alumina matrix containing copper and chromium and examines the effect of the reinforcement and casting speed on the obtained microstructure. Al2O3-Cu-Cr composites with a microstructure gradient were produced via centrifugal slip casting. The research reveals that adding chromium to the Al2O3-Cu system improves the connection between the ceramic and metal particles, probably by reducing the contact angle at the interface between the ceramic and metallic phases during sintering. Additionally, it was found that higher casting speed was conducive to obtaining a better connection at the interface of ceramics and metal.
ABSTRACT
The need to reduce greenhouse gas emissions dictates the search for new methods and materials. Here, a novel type of inorganic-organic hybrid materials Fe@MWCNT-OH/SPEEK (with a new type of CNT characterized by increased iron content, 5.80 wt%) for CO2 separation is presented. The introduction of nanofillers into a polymer matrix has significantly improved hybrid membrane gas transport (D, P, S, and α CO2/N2 ), and magnetic, thermal, and mechanical parameters. It was found that magnetic casting has improved the alignment and dispersion of Fe@MWCNT-OH carbon nanotubes. At the same time, CNT and polymer chemical modification enhanced interphase compatibility and membrane CO2 separation efficiency. The thermooxidative stability, and mechanical and magnetic parameters of composites were improved by increasing new CNT loading. Cherazi's model turned out to be suitable for describing the CO2 transport through analyzed hybrid membranes. The comparison of the transport and separation properties of the tested membranes with the literature data indicates their potential application in the future and the direction of further research.
ABSTRACT
This study's main goal was to obtain and characterize Al2O3-Cu-Ni composites with different metallic phase content. The study analyzed the three series of samples differing in the metallic phase 5, 10, 15 vol.% volume contents. An identical volume share of the metallic components in the metallic phase was used. Ceramic-metal composites were formed using uniaxial pressing and sintered at a temperature of 1400 °C. The microstructural investigation of the Al2O3-Cu-Ni composite and its properties involved scanning electron microscopes observations and X-ray diffraction. The size of the metallic phase in the ceramic matrix was performed using a stereological analysis. Microhardness analysis with fracture toughness measures was applied to estimate the mechanical properties of the prepared materials. Additionally, magnetic measurements were carried out, and the saturation magnetization was determined on the obtained magnetic hysteresis loops. The prepared samples, regardless of the content of the metallic phase in each series, were characterized by a density exceeding 95% of the theoretical density. The magnetic measurements exhibited that the fabricated composites had ferromagnetic properties due to nickel and nickel-rich phases. The hardness of the samples containing 5, 10, 15 vol.% metallic phases decreased with an increase in the metallic phase content, equal to 17.60 ± 0.96 GPa, 15.40 ± 0.81 GPa, 12.6 ± 0.36 GPa, respectively.
ABSTRACT
Novel inorganic-organic hybrid membranes Fe@MWCNT/PPO or Fe@MWCNT-OH/SPPO (with a new type of CNTs characterized by increased iron content 5.80 wt%) were synthesized for CO2 separation. The introduction of nanofillers into the polymer matrix has significantly improved the hybrid membrane's gas transport (D, P, S, and αCO2/N2), magnetic, thermal, and mechanical parameters. It was found that magnetic casting has improved the alignment and dispersion of Fe@MWCNTs. At the same time, CNTs and polymer chemical modification enhanced interphase compatibility and the membrane's CO2 separation efficiency. The thermo-oxidative stability and mechanical and magnetic parameters of composites were improved by increasing new CNTs loading. Cherazi's model turned out to be suitable for describing the CO2 transport through analyzed hybrid membranes.
ABSTRACT
In this study, ceramic-metal composites in the Al2O3/Ti/Ni system were fabricated using the slip casting method. Two series of composites with 15 vol.% metal content and different solid phase contents were obtained and examined. A proper fabrication process allows obtaining composites enhanced by intermetallic phases. The microstructure of the base powders, slurries, and sintered composites was analyzed by scanning electron microscope. Analysis of the sedimentation tendency of slurries was carried out. The phase composition of the sintered samples was examined by X-ray diffraction analysis. A monotonic compression test was used to investigate the mechanical properties of the composites. A fractography investigation was also carried out. The research conducted revealed that the slip casting method allows the obtaining of composites enhanced by intermetallic phases (TiNi, Ni3Ti). The results show the correlation between solid-phase content, microstructure, and mechanical properties of the composites.
ABSTRACT
The main aim of the investigation was to determine the impact of the content of nickel and the content of slurry on the nature of the microstructure and physical properties of the final products. In the study, six types of slurries were examined and prepared, differing in both the amounts of content of Ni metallic phase particles (5 vol.%, 10 vol.%, and 20 vol.%) and the amount of content of solid content in the prepared slurries (35 vol.%, and, 50 vol.%). The centrifugal slip casting (CSC) method in a magnetic field was used to fabricate the composites. This technique allowed the production of high-density ZrO2-Ni composites after sintering. Composites containing 50 vol.% of the solid content were characterized by a relative density equal to 99%. Applying the magnetic field allows controlling the distribution of the ferromagnetic phase (Ni) in the ceramic matrix (ZrO2). Based on the results obtained, it was found that the nature of the composites obtained is influenced by the rheological properties of the slurries, depending on their composition. The applicability of the CSC in the magnetic field technique for the production of the composite is characterized by a gradient in the distribution of components on the longitudinal section and has been proved. Based on the obtained results, a model for shaping the microstructure of composites with a longitudinal section was proposed. This work enabled a better understanding of creating microstructures in materials fabricated by centrifugal slip casting in a magnetic field.
ABSTRACT
The aim of the present work was to investigate an influence of W addition on the phase constitution, microstructure and magnetic properties of the Pr9Fe65WxB26-x (where: x = 2, 4, 6, 8) alloy ribbons. Ribbons were obtained using the melt-spinning technique under low pressure of Ar. The as-cast samples were fully amorphous and revealed soft magnetic properties. These facts were confirmed by X-ray diffractometry, Mössbauer spectroscopy and magnetic measurements. Differential scanning calorimetry and differential thermal analysis allowed us to determine the thermal stability parameters of the amorphous phase. The Kissinger plots were constructed in order to calculate the activation energies for crystallization. Heat treatment carried out at various temperatures caused changes in the phase constitution and magnetic properties of the alloys. The phase analysis has shown the presence of the hard magnetic Pr2Fe14B and paramagnetic Pr1+xFe4B4 phases. Additionally, for the x = 2 and x = 6 alloys, a crystallization of soft magnetic Fe2B and α-Fe phases was observed. The Mössbauer spectroscopy allowed us to determine the volume fractions of constituent phases formed during annealing. The microstructure of annealed ribbons was observed using transmission electron microscopy.
ABSTRACT
In the present study, the phase constitution, microstructure and magnetic properties of the nanocrystalline magnets, derived from fully amorphous or partially crystalline samples by annealing, were analyzed and compared. The melt-spun ribbons (with a thickness of ~30 µm) and suction-cast 0.5 mm and 1 mm thick plates of the Pr9Fe50Co13Zr1Nb4B23 alloy were soft magnetic in the as-cast state. In order to modify their magnetic properties, the annealing process was carried out at various temperatures from 923K to 1033K for 5 min. The Rietveld refinement of X-ray diffraction patterns combined with the partial or no known crystal structures (PONKCS) method allowed one to quantify the component phases and calculate their crystalline grain sizes. It was shown that the volume fraction of constituent phases and their crystallite sizes for the samples annealed at a particular temperature, dependent on the rapid solidification conditions, and thus a presence or absence of the crystallization nuclei in the as-cast state. Additionally, a thermomagnetic analysis was used as a complementary method to confirm the phase constitution. The hysteresis loops have shown that most of the samples exhibit a remanence enhancement typical for the soft/hard magnetic nanocomposite. Moreover, for the plates annealed at the lowest temperatures, the highest coercivities up to ~1150 kA/m were measured.
ABSTRACT
The mechanochemical covalent functionalization of carbon-encapsulated iron nanoparticles (CEINs) is reported. Unprotected sugars (mannose, galactose, ß-cyclodextrin) and amino sugars (glucosamine and chitosan) were successfully conjugated to the surface of CEINs. The developed grinding-induced methods employ (i) the 1,3-dipolar cycloadditions of nitrile oxides or azomethine ylides and (ii) amidation-type reactions with the inclusion of carboxyl-functionalized CEINs and amino sugars. All the developed mechanochemical processes are fast (reaction time 10 min) and result in high degrees of coverage (7.3-31.5 wt%). The presented functionalization routes also constitute easy to perform and environmentally improved protocols. Moreover, the use of toxic organic solvents is not required. A comprehensive study on the colloidal stability of the sugar-functionalized CEINs is also included in this work. The results of the turbidimetric analyses reveal that both grinding-induced formation of amide bonds and the cycloadditions of sugar moieties to the surface of CEINs result in the significant improvement of their colloidal stability. The highest stability of the aqueous dispersion was found for CEINs functionalized with ß-cyclodextrin. The comparative studies between the classical wet approach and the grinding-induced functionalization of CEINs show that the herein developed environmentally improved method increases the colloidal stability three times. The crucial role of the mechanochemical approach in the covalent functionalization of CEINs and the improvement of their colloidal stability is discussed in this work.
ABSTRACT
The nanoparticles comprising of iron core and carbon shell were decorated with ferrocene derivatives: ferrocenecarboxaldehyde (Fc-1) and ferrocenecarboxaldehyde oxime (Fc-2). A microdrop of suspension of the nanoconjugate was placed on a glassy-carbon electrode to prepare the recognition/sensing layer. Drying and purification of the sensing layer resulted in a well-defined and stable square-wave voltammogram of the ferrocene moiety. The height of the voltammetric peak increased in the presence of ceruloplasmin. That increase was linearly dependent on the logarithmic concentration of ceruloplasmin in blood. The applied external magnetic field was a factor which yielded better sensitivity and repeatability of the sensor response. The linearity of sensor response was found to be between 0.001 and 10µgdL-1 and 0.05-10µgdL-1 for both nanoconjugates: Fe@C-Fc-1 and Fe@C-Fc-2, in the presence and absence of the magnet, respectively. The obtained detection limit (LOD) for Fe@C-Fc-1 was found to be 0.60 and 0.10µgdL-1 in the absence and presence of magnetic field, respectively, whilst for Fe@C-Fc-2 was 0.4 and 0.07µgdL-1 in the absence and presence of a magnet, respectively. The proposed method is selective because the presence of common antioxidants in blood did not interfere significantly with the determination of the concentration of ceruloplasmin.
Subject(s)
Biosensing Techniques/methods , Ceruloplasmin/isolation & purification , Ferrous Compounds/chemistry , Metallocenes/chemistry , Nanoconjugates/chemistry , Carbon/chemistry , Humans , Iron , Limit of Detection , Metal Nanoparticles/chemistry , Oximes/chemistryABSTRACT
Carbon encapsulated magnetic nanoparticles may find many prospective biomedical applications, e.g., in drug and gene delivery systems, disease detection, cancer therapy, rapid toxic cleaning, biochemical sensing, and magnetic resonance imaging. Each of these applications hinges on the relationship between magnetic fields and biological systems. Herein we present the results on the thermal stability of carbon encapsulated magnetic nanoparticles. The products were synthesized by using induction radio frequency (RF) thermal plasma. Phase composition and morphology were studied by powder X-ray diffraction and HRTEM, respectively. Thermal stability was investigated by thermogravimetry and differential thermal analyses. Carbon nanostructures were thermally stable up to 500 K.
