Effects of Denture Treatment on Salivary Metabolites: A Pilot Study.

Symptoms of oral discomfort such as dry mouth are common in older people wearing dentures. Such symptoms are mainly treated symptomatically. Many of these symptoms are related to saliva, and associations with salivary volume have been reported. Although denture treatment improves symptoms by increasing the amount of saliva, the effects on salivary components remain unclear. This study aimed to investigate the effects of denture treatment on salivary metabolite changes based on salivary metabolome analyses. We enrolled 21 patients requiring denture treatment. At the first visit, and after completion of denture treatment, saliva outflow was measured under resting and stimulated conditions, samples for salivary metabolite analysis were collected, and masticatory efficiency was tested. In all participants, masticatory efficiency increased after denture treatment. Moreover, the amounts of resting and stimulated saliva were increased. Using salivary metabolome analysis, 61 salivary metabolites were detected. Substantial concentration changes were observed for 4 and 21 metabolites in resting and stimulated saliva, respectively. The four metabolites common to both saliva tests had significantly lower concentrations after treatment. These results suggest that the improvement in masticatory function by dentures is related not only to salivary secretion volume, but also to salivary metabolite composition.

A Preliminary Pilot Study: Metabolomic Analysis of Saliva in Oral Candidiasis.

Early detection of oral candidiasis is essential. However, most currently available methods are time-consuming and useful only for screening patients. Previous studies on the relationship between oral candidiasis and saliva have focused on saliva volume and not on its components. Therefore, to clarify the effects of oral candidiasis on salivary metabolites, the relationship between salivary components and oral candidiasis was investigated by comparing the salivary metabolites of oral candidiasis patients and those not previously diagnosed with candidiasis. Forty-five participants visiting our university hospital were included and classified into two groups, the Candida group and the control group, based on the Candida detection test results. The unstimulated saliva was collected using the spitting method over 15 min, and the stimulated saliva was collected using the gum-chewing method over 10 min. The saliva volume was measured, and the saliva samples were frozen and analyzed metabolomically. Metabolome analysis revealed 51 metabolites with peak detection rates exceeding 50%. There was no significant difference in age and sex between the Candida and control groups. In the Candida group, five metabolites (tyrosine, choline, phosphoenolpyruvate, histidine, and 6-phosphogluconate) were significantly elevated in the unstimulated, two (octanoic acid and uridine monophosphate(UMP)) were significantly increased, and four (ornithine, butyrate, aminovalerate and aminolevulinate) were significantly decreased in the stimulated saliva. This study suggests the possibility of identifying metabolites specific to patients with oral candidiasis, which could aid prompt diagnosis.

Patient satisfaction with conventional dentures vs. digital dentures fabricated using 3D-printing: A randomized crossover trial.

PURPOSE: Evidence regarding the performance of digital dentures (DDs) fabricated using 3D printing is insufficient. This study aimed to evaluate patient satisfaction with conventional dentures (CDs) and DDs fabricated using 3D printing. METHODS: This randomized controlled trial was conducted between November 2017 and May 2020. In the CD-DD group, CDs were fabricated before DDs, while the protocol was reversed in the DD-CD group. The primary outcome was patient satisfaction, quantified using a 100-mm visual analog scale, which assessed chewing efficiency, pain, stability, retention, comfort, esthetics, ease of cleaning, phonetics, and general satisfaction. Secondary outcomes were quality of life (QOL), number of visits, time required for definitive denture fabrication, number of adjustment appointments, and time required for denture stabilization after denture delivery. RESULTS: Patient satisfaction with CDs was superior in terms of phonetics, ease of cleaning, stability, comfort, and general satisfaction. Secondary outcomes such as social disability and the number of clinic visits were significantly lower in patients with DDs. However, the two groups showed no significant differences in the other outcomes. Although patient satisfaction with DDs was inferior to that with CDs, 20% of patients preferred and used DDs (12 patients preferred CDs, and three patients opted for DDs). CONCLUSION: Although patient satisfaction or QOL with DDs may be somewhat inferior to that with CDs, 20% of patients preferred and used DDs daily. Thus, DDs fabricated using 3D printing may have comparable practicality and efficacy to CDs.

Application of multi-directional forged titanium for prosthetic crown fabrication by CAD/CAM.

Titanium are often used as dental materials, pure titanium present low strength and titanium alloy is reported poor biocompatibility, respectively. To overcome the problem, we fabricated high-strength multi-directional forged (MDF) titanium with improved mechanical properties without changing the chemical composition and evaluated its applicability in prosthetic crowns. Cutting tests: the average absolute value of the difference before and after cutting was calculated as the uncut amount. Surface evaluations: MDF titanium, pure titanium, and the Ti-6Al-4V alloy were the surface properties (the surface roughness, the contact angles, glossiness) of the samples were evaluated. The fitness test used digital data. These demonstrated that the good workability of high-strength MDF titanium. The surface-roughness and contact-angle properties of MDF titanium and pure titanium were similar. The fitness test showed no significant differences between MDF titanium and pure titanium crowns. These results suggest that MDF titanium is promising for fabricating prosthetic crowns in dental applications.

Positive Effects of Saliva on Oral Candidiasis: Basic Research on the Analysis of Salivary Properties.

The major causes of oral candidiasis include decreased salivary flow rate and the use of ill-fitting dentures. However, the relationships among prosthetic treatment, saliva, and Candida albicans have not been elucidated. This study aimed to examine the effects of prosthetic treatment and changes in saliva (mainly the salivary flow rate) on oral candidiasis symptoms. Participants requiring prosthetic treatment underwent testing for C. albicans, salivary flow rate, intraoral symptoms, and bite force at the initial visit and four months after treatment to evaluate pretreatment and post-treatment changes. The relationships among C. albicans, salivary flow rate, dentures, and intraoral symptoms were analyzed using multiple regression analysis. Denture treatment improved activity against C. albicans as well as the salivary flow rate, intraoral symptoms, and masticatory function. Multiple regression analysis revealed that changes in the stimulated salivary flow rate due to prosthetic treatment significantly improved C. albicans detection (p = 0.011), intraoral symptoms (p = 0.037), and bite force (p = 0.031). This study showed that prosthetic treatment improved salivary flow and intraoral symptoms and confirmed the influence of stimulated salivary flow rate changes.

Effects of inter-day and intra-day variation on salivary metabolomic profiles.

BACKGROUND: Salivary secretion is an important parameter reflecting the health status of an individual and has been used clinically for the diagnosis of various oral diseases, such as xerostomia. Salivary metabolomic profiling is considered an emerging potential tool for the detection of various systemic diseases. To our knowledge, this is the first study to investigate the quantitative relationship between salivary secretion volume and salivary metabolomic profile. METHODS: To evaluate inter- and intra-day variations in salivary secretion, 234 saliva samples were collected three times per day for three days from 13 subjects and analyzed. Capillary electrophoresis-mass spectrometry was used for non-targeted quantification of water-soluble metabolites. RESULTS: No significant inter- or intra-day variations were observed in salivary secretion volume. No significant inter-day variations were observed in metabolomic patterns. In contrast, significant intra-day variations were observed in salivary metabolomic profiles. The difference was more obvious for stimulated saliva than for unstimulated saliva. These profile changes were independent of salivary secretion volume. CONCLUSIONS: Our results indicated that diurnal change had a greater effect on salivary metabolomic profiles than the other factors. Hence, sampling time should be tightly controlled to minimize unexpected bias in the clinical use of salivary metabolomics.