Microwave-assisted catalytic pyrolysis of waste cooking oil to monocyclic aromatics under a bifunctional SiC ball catalyst.

Catalytic pyrolysis technology proves to be a highly effective approach for waste cooking oil management. However, high-pressure drops and easy deactivation of powder catalysts hinder the industrialization of this technology. In this study, a bifunctional SiC ball (ZSM-5/SiC ball structured) catalyst was prepared to produce monocyclic aromatics. Bifunctional SiC ball catalyst demonstrates notable microwave-responsive properties and remarkable catalytic efficacy. Results showed that the content of monocyclic aromatics under BFSB catalysis with microwave heating was the highest. Weight hourly space velocity is no longer one of the main factors affecting microwave-assisted catalytic pyrolysis under bifunctional SiC ball catalyst. Monocyclic aromatics content did not decrease significantly and was still higher than 86% when space velocity increased from 30 h-1 to 360 h-1. The highest space velocity could only be 180 h-1 under Powder ZSM-5, and the content of the monocyclic aromatics dropped rapidly to 67.68%. Furthermore, even after five operating cycles, the content of monocyclic aromatics with bifunctional SiC ball catalyst continues to surpass the initial content observed with Powder ZSM-5 at 500 °C and 180 h-1. Related characterizations revealed that coking is the primary cause of catalyst deactivation for both catalyst types; however, the bifunctional SiC ball catalyst exhibits a 29.1% lower occurrence of polyaromatic coke formation compared to Powder ZSM-5.

Production of C5-C12 olefins by catalytic pyrolysis of low-density polyethylene with MCM-41 in CO2/N2.

The current high volume of plastic waste, but low recycling rate, has led to environmental pollution and wasted energy. Greenhouse gas CO2 can facilitate thermal cracking to dehydrogenate waste plastics, and has potential value for producing olefins. In this work, the pyrolysis properties of low-density polyethylene (LDPE) were studied by thermogravimetric analysis and Py-GC/MS. The effect of the pyrolysis atmosphere, using N2 or CO2, with various MCM-41 catalyst ratios on pyrolysis product distribution, were investigated. The experimental results show that the olefin selectivity under a N2 atmosphere was from 30.32 % to 44.66 % which increased as the MCM-41 catalyst was increased. Under a CO2 atmosphere, the olefin selectivity reached a maximum of 60.39 %. The Boudouard reaction was also enhanced by the introduction of CO2. The carbon content of the subdivided olefins showed that in CO2, the promotion of C5-C12 olefins was relatively weak when non-catalyzed or at low catalytic ratios, but increased significantly at higher MCM-41 catalyst ratios. With a ratio of LDPE: MCM-41 = 5:4, the CO2 atmosphere showed the greatest promotion of C5-C12 olefins over N2, with an increase of 14.66 % compared to N2, representing a 48.54 % yield of the liquid product. Producing C5-C12 olefins under these conditions maximized energy efficiency. These results show that catalytic pyrolysis of LDPE under a CO2 atmosphere has great potential to produce C5-C12 olefins, which can be used to produce high-value chemicals such as naphtha and gasoline. This opens new opportunities for the chemical recycling of plastic waste.

Research progress on pyrolysis of nitrogen-containing biomass for fuels, materials, and chemicals production.

Pyrolysis of nitrogen-containing biomass holds tremendous potential for producing varieties of high value-added products, alleviating energy depletion. Based on the research status about nitrogen-containing biomass pyrolysis, the effect of biomass feedstock composition on pyrolysis products is first introduced from the aspects of elemental analysis, proximate analysis, and biochemical composition. The properties of biomass with high and low nitrogen used in pyrolysis are briefly summarized. Then, with the pyrolysis of nitrogen-containing biomass as the core, biofuel characteristics, nitrogen migration during pyrolysis, the application prospects, unique advantages of nitrogen-doped carbon materials for catalysis, adsorption and energy storage are introduced, as well as their feasibility in producing nitrogen-containing chemicals (acetonitrile and nitrogen heterocyclic) are reviewed. The future outlook for the application of the pyrolysis of nitrogen-containing biomass, specifically, how to realize the denitrification and upgrading of bio-oil, performance improvement of nitrogen-doped carbon materials, as well as separation and purification of nitrogen-containing chemicals, are addressed.

Co-torrefaction of corncob and waste cooking oil coupled with fast co-pyrolysis for bio-oil production.

Lignocellulosic biomass is a rich source of fixed renewable carbon and a promising alternative to fossil sources. However, low effective hydrogen to carbon ratio limits its applications. This work studied the influence of oil-bath co-torrefaction of corncob and waste cooking oil for co-pyrolysis. It was compared with dry torrefaction and hydrothermal wet torrefaction firstly. Residual of oil-bath co-torrefaction were the highest of 97.01 %. Oil-bath co-torrefaction could maximize hydrogen atoms retention in corncob, which has a positive significance for deoxygenation during pyrolysis. Oil-bath co-torrefaction could also reduce the average activation energy required for corncob decomposition, while it was increased with dry torrefaction. Oil-bath co-torrefaction coupled with co-pyrolysis was more suitable for hydrocarbon-rich bio-oil production. Oil-bath co-torrefaction temperature had the greatest influence on bio-oil composition. High pressure promoted formation of the CC double bond and degradation of lignin, which further promoted the formation of monocyclic aromatics in bio-oil.

Microwave catalytic co-pyrolysis of waste cooking oil and low-density polyethylene to produce monocyclic aromatic hydrocarbons: Effect of different catalysts and pyrolysis parameters.

It is promising to convert waste oil and plastics to renewable fuels and chemicals by microwave catalytic co-pyrolysis, enabling pollution reduction and resource recovery. The purpose of this study was to evaluate the effect of catalysts on the product selectivity of microwave-assisted co-pyrolysis of waste cooking oil and low-density polyethylene and optimize the pyrolysis process, including pyrolysis temperature, catalytic temperature, waste cooking oil to low-density polyethylene ratio, and catalyst to feedstocks ratio. The results indicated that catalysts had a great influence on the product distribution, and the yield of BTX (benzene, toluene, and xylenes), which increased in the following order: SAPO-34 < Hß < HY < HZSM-5. HZSM-5 was more active for the formation of light aromatic hydrocarbons as compared to others, where the concentrations of toluene, benzene and xylenes reached 252.59 mg/mL, 114.7 mg/mL and 132.91 mg/mL, respectively. The optimum pyrolysis temperature, catalytic temperature, waste cooking oil to low-density polyethylene ratio and catalyst to feedstocks ratio could be 550 °C, 450 °C, 1:1 and 1:2, respectively, to maximize the formation of BTX and inhibit the formation of polycyclic aromatic hydrocarbons.

Pyrolysis of soybean soapstock for hydrocarbon bio-oil over a microwave-responsive catalyst in a series microwave system.

A novel Silicon carbide (SiC) foam ceramic based ZSM-5/SiC nanowires microwave-responsive catalyst was developed to upgrade the pyrolysis volatiles in a microwave-assisted series system (both the pyrolysis and catalytic systems were heated by microwave). The growth of SiC nanowires was helpful for the ZSM-5 growth on the SiC foam ceramic. Because the specific surface area of SiC foam ceramic was improved. The dielectric properties of the composite catalyst were improved due to the growth of SiC nanowires. Bio-oil composition analysis showed that area percentage of hydrocarbons and aromatic hydrocarbons could reach 80.89% and 40.48% at catalytic temperature of 450 ℃and 500 ℃, respectively. The microwave-responsive composite catalyst had good aromatization performance in microwave-assisted series system due to high dielectric properties and specific surface area. The composite catalyst performed well after five-cycle regeneration, and the hydrocarbon content could still reach 76.40%, which is 80.89% for the original catalyst.

Integrating pyrolysis and ex-situ catalytic reforming by microwave heating to produce hydrocarbon-rich bio-oil from soybean soapstock.

The composite catalysts were synthesized with SiC powder and ZSM-5 and were characterized by Brunauer-Emmett-Teller, X-ray diffraction, thermogravimetric analysis, pyridine-infrared spectroscopy, and scanning electron microscopy. The catalysts showed a high heating rate and excellent catalytic performance for pyrolysis vapors, and the product fractional distribution and chemical compositions of bio-oil in a tandem system (microwave pyrolysis and microwave ex-situ catalytic reforming) was examined. Experimental results confirmed the quality of bio-oil produced by the microwave-induced catalytic reforming was better than that product through electric heating. Additionally, 36.94 wt% of bio-oil was obtained using the catalyst with 20%ZSM-5/SiC under the following conditions: feed-to-catalyst ratio, 2:1; pyrolysis temperature, 550 °C; and catalytic temperature, 350 °C. The selectivities of hydrocarbons reached up to 75.88%. After five cycles, the activity of the regenerated composite catalyst was retained at 95% of the original catalyst.

Microwave-assisted catalytic upgrading of co-pyrolysis vapor using HZSM-5 and MCM-41 for bio-oil production: Co-feeding of soapstock and straw in a downdraft reactor.

Microwave-assisted co-pyrolysis of low hydrogen-to-carbon and high hydrogen-to-carbon effective ratio materials with the aid of HZSM-5 and MCM-41 is a promising technique to improve the bio-oil quality. The low content of hydrocarbons and short life cycle of catalyst limit the application of pyrolysis technology in biomass energy conversion. The effects of catalytic temperature, and HZSM-5-to-MCM-41, feedstock-to-catalyst, and straw-to-soapstock ratios on the yield and composition of bio-oil were studied in this work. The quality of bio-oil during biomass pyrolysis can be improved by adjusting the operating conditions. The optimal catalytic temperature, and ratios of HZSM-5-to-MCM-41, feedstock-to-catalyst, and straw-to-soapstock were 400 °C, 1:1, 2:1, and 1:2, respectively. The addition of MCM-41 was beneficial in prolonging the life of HZSM-5 since the macromolecular compounds cracked when MCM-41 was added which restrain the generation of coke. The co-pyrolysis of soapstock with straw advanced the deoxygenation of oxygen-containing compounds especially phenol from straw during pyrolysis.

Microwave-assisted co-pyrolysis of lignin and waste oil catalyzed by hierarchical ZSM-5/MCM-41 catalyst to produce aromatic hydrocarbons.

Microwave-assisted catalytic fast co-pyrolysis (MACFP) of lignin and waste oil with SiC as microwave absorbent and hierarchical ZSM-5/MCM-41 as catalyst were implemented in a microwave-induced reactor. ZSM-5/MCM-41 is a kind of composite catalyst with MCM-41 as shell and ZSM as core. The effects of catalyst temperature, the ratio of feedstock-to-catalyst and the ratio of two reactants (lignin and waste oil) on product distribution and yield were studied. The study shows that catalytic co-pyrolysis is a complex reaction process, and many reaction conditions could affect the final reaction results. The optimum reaction conditions are as follows: catalytic temperature 400 °C, the feedstock-to-catalyst ratio of 10:1 and the ratio of lignin to waste oil of 2:1. Under this reaction condition, the conversion of feedstocks reached 76.00%, the proportion of aromatics was 50.31% and the selectivity of monocyclic aromatic hydrocarbons (MAHs) was 42.83%.