Performance Differences of Hexavalent Chromium Adsorbents Caused by Graphene Oxide Drying Process.

In this study, the influence of drying conditions on amine (-NH3) functionalization of graphene oxide (GO) was evaluated, and the hexavalent chromium (Cr(VI)) adsorption efficiency of the prepared materials was compared. 3-[2-(2-aminoehtylamino) ethylamino]propyl-trimethoxysilane (3N) was used for amine functionalization. The synthesized materials were analyzed by SEM, BET, TGA, XPS, and EA. TGA results showed that the solution-GO (SGO) was functionalized by more 3N molecules than freeze-dried GO (FDGO) and oven-dried GO (ODGO). Additionally, XPS analysis also showed that the ratio of N/C and Si/C was relatively high in SGO than FDGO and ODGO. The maximum adsorption capacity of SGO, FDGO, and ODGO for Cr(VI) was 258.48, 212.46, and 173.45 mg g-1, respectively. These results indicate that it is better to use SGO without drying processes for efficient amine functionalization and Cr(VI) removal. However, when the drying process is required, freeze-drying is better than oven-drying.

Most suitable amino silane molecules for surface functionalization of graphene oxide toward hexavalent chromium adsorption.

Adsorption is a simple and effective method for the removal of hexavalent chromium (Cr(VI)) from contaminated water. Several amino silane-graphene oxide (GO) composites with different species of amino groups (pN-GO, psN-GO, and pssN-GO; p: primary, s: secondary, N: amine) were evaluated to investigate their adsorption capacity and the effects of primary and secondary amines on Cr(VI) adsorption. We conducted a quantitative analysis to reveal the difference between primary and secondary amines in terms of Cr(VI) removal efficiency. A synergic effect was observed between the neighboring secondary amines in pssN-GO. From the Langmuir model prediction, we found that the composite with pssN-GO exhibited the highest maximum adsorption capacity (260.74 mg/g), followed by those with psN-GO (208.22 mg/g) and pN-GO (189.47 mg/g). Monolayer adsorption was more dominant when using pssN-GO, with the pseudo-second-order model best fitting the kinetic experiment results, whereas multilayer adsorption was dominant when using psN-GO and pN-GO.

Investigation of the mechanism of chromium removal in (3-aminopropyl)trimethoxysilane functionalized mesoporous silica.

We are proposed that a possible mechanism for Cr(VI) removal by functionalized mesoporous silica. Mesoporous silica was functionalized with (3-aminopropyl)trimethoxysilane (APTMS) using the post-synthesis grafting method. The synthesized materials were characterized using transmission electron microscopy (TEM), X-ray diffraction (XRD), N2 adsorption-desorption analysis, Fourier-transform infrared (FT-IR), thermogravimetric analyses (TGA), and X-ray photoelectron spectroscopy (XPS) to confirm the pore structure and functionalization of amine groups, and were subsequently used as adsorbents for the removal of Cr(VI) from aqueous solution. As the concentration of APTMS increases from 0.01 M to 0.25 M, the surface area of mesoporous silica decreases from 857.9 m2/g to 402.6 m2/g. In contrast, Cr(VI) uptake increases from 36.95 mg/g to 83.50 mg/g. This indicates that the enhanced Cr(VI) removal was primarily due to the activity of functional groups. It is thought that the optimum concentration of APTMS for functionalization is approximately 0.05 M. According to XPS data, NH3+ and protonated NH2 from APTMS adsorbed anionic Cr(VI) by electrostatic interaction and changed the solution pH. Equilibrium data are well fitted by Temkin and Sips isotherms. This research shows promising results for the application of amino functionalized mesoporous silica as an adsorbent to removal Cr(VI) from aqueous solution.

Electrochemical synthesis of formic acid from CO2 catalyzed by Shewanella oneidensis MR-1 whole-cell biocatalyst.

The electro-biocatalytic conversion of CO2 into formic acid using whole-cell and isolated biocatalysts is useful as an alternative route for CO2 sequestration. In this study, Shewanella oneidensis MR-1 (S. oneidensis MR-1), a facultative aerobic bacterium that has been extensively studied for its utility as biofuel cells as well as for the detoxification of heavy metal oxides (i.e., MnO2, uranium), has been applied for the first time as a whole-cell biocatalyst for formic acid synthesis from gaseous CO2 and electrons supplied from an electrode. S. oneidensis MR-1, when aerobically grown in Luria-Bertani (LB) medium, exhibited its ability as a whole-cell biocatalyst for the conversion of CO2 into formic acid with moderate productivity of 0.59 mM h-1 for 24 h. In addition, an optimization of growth conditions of S. oneidensis MR-1 resulted in a remarkable increase in productivity. The CO2 reduction reaction catalyzed by S. oneidensis MR-1, when anaerobically grown in newly optimized LB medium supplemented with fumarate and nitrate, exhibited 3.2-fold higher productivity (1.9 mM h-1 for 72 h) compared to that grown aerobically in only LB medium. Furthermore, the average conversion rate of formic acid synthesis catalyzed by S. oneidensis MR-1 when grown in the optimal medium over a period of 72 h was 3.8 mM h-1 g-1 wet-cell, which is 9.6-fold higher than that catalyzed by Methylobacterium extorquens AM1 whole-cells in our previous study.

Phosphorous recovery from sewage sludge using calcium silicate hydrates.

Phosphorous is an essential limiting nutrient for which there is no substitute. Its efficient recovery from sewage treatment plants is important to mitigate both dependence on limited reserves of exploitable phosphate rock and eutrophication of surface waters. Here, we evaluate the use of calcium silicate hydrates (CSH) to recover phosphorous eluted from sewage sludge. Phosphorous elution experiments were conducted with acid and base leaching solutions. The phosphorous recovery efficiency with CSH was compared to that with other calcium compounds, and the final product was analyzed to assess its potential value as fertilizer. Dried sewage sludge from the West Lake Ecological Water Resource Center, South Korea, having 123 g-P kg-1, was used for these tests. About 55% of the phosphorus in the sludge was released with an elution solution of 0.1 M H2SO4. A dose of 15 g L-1 of CSH recovered 89.6% of the eluted phosphorous without the need for additional pre-treatment, and the resulting calcium phosphate product (in brushite form, based on XRD analysis) exhibited superior settleability than that resulting from Ca(OH)2- and CaCl2-induced precipitation. XRD peaks of the calcium sulfate hydrate (in gypsum form) and residual CSH were also observed. The final product contained a relatively high content of the total P2O5 eluted in a 2% citric acid solution (43.1%), which suggests that it might be readily used to fertilize crops.

Comparative analysis of two types of methanol dehydrogenase from Methylophaga aminisulfidivorans MPT grown on methanol.

Two types of methanol dehydrogenase (MDH) were obtained from a novel marine methylotrophic bacterium, Methylophaga aminisulfidivorans MP(T), grown on methanol. Type I MDH consisted of two identical dimers of α (65.98 kDa) and ß (7.58 kDa) subunits organized to form the α(2)ß(2) tetramer. Type II MDH contained an additional MxaJ protein (27.86 kDa) and had more specific activity than type I MDH. The K(m) values of type I and II MDH for methanol under cytochrome c(L) reduction assay system were estimated to be 50.3 and 13.0 µM, respectively, and the isoelectric points of type I and II MDH were determined to be 5.4 and 5.8, respectively. The average molar ratios of α:ß, α:MxaJ, and ß:MxaJ in type II MDH were approximately 1:0.99, 1:0.41 and 1:0.42, respectively. Based on these results, the original conformation of the MDH of M. aminisulfidivorans MP(T) is most likely the α(2)ß(2)-MxaJ complex. During purification, the lysozyme and freeze-thawing cell disruption method significantly increased the amount of type II MDH in the soluble fraction compared with strong physical disruption methods such as sonication and French Press.

Purification, crystallization and preliminary X-ray crystallographic analysis of a methanol dehydrogenase from the marine bacterium Methylophaga aminisulfidivorans MP(T).

Methylophaga aminisulfidivorans MP(T) is a marine methylotrophic bacterium that utilizes C(1) compounds such as methanol as a carbon and energy source. The released electron from oxidation flows through a methanol-oxidizing system (MOX) consisting of a series of electron-transfer proteins encoded by the mox operon. One of the key enzymes in the pathway is methanol dehydrogenase (MDH), which contains the prosthetic group pyrroloquinoline quinone (PQQ) and converts methanol to formaldehyde in the periplasm by transferring two electrons from the oxidation of one methanol molecule to the electron acceptor cytochrome c(L). In order to obtain molecular insights into the oxidation mechanism, a native heterotetrameric α(2)ß(2) MDH complex was directly purified from M. aminisulfidivorans MP(T) grown in the presence of methanol and crystallized. The crystal diffracted to 1.7 Šresolution and belonged to the monoclinic space group P2(1) (unit-cell parameters a = 63.9, b = 109.5, c = 95.6 Å, ß = 100.5°). The asymmetric unit of the crystal contained one heterotetrameric complex, with a calculated Matthews coefficient of 2.24 Å(3) Da(-1) and a solvent content of 45.0%.

Isolation and taxonomic characterization of a novel type I methanotrophic bacterium.

A methane-oxidizing bacterium was isolated from the effluent of manure and its molecular and biochemical properties were characterized. The isolate was aerobic, Gram-negative, and non-motile. The organism had a type I intracytoplasmic membrane structure and granular inclusion bodies. The outer cell wall surface (S-layers) was tightly packed with cup-shaped structures. Colonies were light yellow on nitrate mineral salt agar medium. In addition, the organism was catalase and oxidase positive. The isolate used the ribulose monophosphate (RuMP) pathway for carbon assimilation, and was able to utilize methane and methanol as a sole carbon and energy source, however, it could not utilize any other organic compounds that were tested. The cells grew well in a mixture of methane and air (methane:air=1:1, v/v) in a compulsory circulation diffusion system, and when grown under those conditions, the optimum pH was approximately 7.0 and the optimal temperature was 30 degrees. In addition, the specific growth rate and generation time were 0.13 per h and 5.43 h, respectively, when grown under the optimum conditions. The major ubiquinone was Q-8, and the G+C mol% of the DNA was 55.3. Phylogenetic analyses based on the 16S rRNA gene sequence comparisons showed that this bacterium belongs to a group of type I methanotrophs, and that it is most closely related to Methylomicrobium, with a sequence similarity of 99%. Therefore, the isolate was named Methylomicrobium sp. HG-1.

[Medical doctors' independence movement during the Japanese colonial period].

There are approximately 10,000 people who have been identified as men of merit for independence movement by the Ministry of Patriots and Veterans Affairs in Korea. Currently, January of 2008, it is assumed that there are 156 doctors (medical school students included) had participated in independence movement, among them, 71 people have received the rewards from the government with the honor of independence movement as a doctor or medical school student. However, there are still 85 doctors have not received any rewards from the government despite their participation in independence movement. Korean doctors and medical students participated in independent movement through many ways in domestic and foreign country during the Japanese colonial period. They made use of their doctor license, and occasionally took part in independent movement as ordinary people. They not only had acted as politicians, diplomats, and medical officers, but also supported medical service, donation campaign, social movement, and educational movement for independent movement against Japanese colonial rule.

Methylophaga aminisulfidivorans sp. nov., a restricted facultatively methylotrophic marine bacterium.

A novel restricted facultatively methylotrophic marine strain, MP(T), possessing the ribulose monophosphate pathway of C(1)-carbon compound assimilation was isolated from a seawater sample obtained from Mokpo, South Korea. The novel isolate is aerobic, Gram-negative, asporogenous and a non-motile short rod. It grows well on methanol, methylated amines, dimethylsulfide and DMSO. Optimal growth occurs with 3 % NaCl at 30 degrees C and pH 7.0. Fructose is utilized as a multicarbon source. Growth factors are not required and vitamin B(12) does not stimulate growth. The cellular fatty acid profile of the novel strain consists primarily of straight-chain saturated C(16 : 0) and unsaturated C(16 : 1) acids. The major ubiquinone is Q-8. The dominant phospholipids are phosphatidylethanolamine and phosphatidylglycerol. The DNA G+C content is 44.9 mol% (T(m)). Based on 16S rRNA gene sequence analysis and DNA-DNA relatedness (25-41 %) with the type strains of marine methylotrophs belonging to the genus Methylophaga, it is suggested that isolate MP(T) represents a novel species, Methylophaga aminisulfidivorans sp. nov. (type strain MP(T)=KCTC 12909(T)=VKM B-2441(T)=JCM 14647(T)).

Characterization of Methylophaga sp. strain SK1 cytochrome cL expressed in Escherichia coli.

Methylophaga sp. strain SK1 is a new restricted facultative methanol-oxidizing bacterium that was isolated from seawater. The aim of this study was to characterize the electron carriers involved in the methanol oxidation process in Methylophaga sp. strain SK1. The gene encoding cytochrome c(L) (mxaG) was cloned and the recombinant gene was expressed in Escherichia coli DH5 under strict anaerobic conditions. The recombinant cytochrome c(L) had the same molecular weight and absorption spectra as the wild-type cytochrome c(L) both in the reduced and oxidized forms. The electron flow rate from methanol dehydrogenase (MDH) to the recombinant cytochrome c(L) was similar to that from MDH to the wild-type cytochrome c(L). These results suggest that recombinant cytochrome c(L) acts as a physiological primary electron acceptor for MDH.

Optimization of methanol biosynthesis from methane using Methylosinus trichosporium OB3b.

Methylosinus trichosporium OB3b oxidized methane to methanol in the presence of a high concentration of Cu2+. Further oxidation of methanol to formaldehyde was prevented by adding 200 mM NaCl which acted as a methanol dehydrogenase H inhibitor. The bacterium, 0.6 mg dry cell ml(-1), in methane/air (1:4, v/v) at 25 degrees C in 12.9 mM phosphate buffer (pH 7) containing 20 mM sodium formate and 200 mM NaCl accumulated 7.7 mM methanol over 36 h.