Correlation Between Microstructure and Tensile Properties of STS 316L and Inconel 718 Fabricated by Selective Laser Melting (SLM).

The correlation between microstructure and tensile properties of selective laser melting (SLM) processed STS 316L and Inconel 718 were investigated at various heights (top, middle and bottom) and planes (YZ, ZX and XY). Columnar grains and dendrites were formed by directional growth during solidification. The average melt pool width and depth, and scan track width were similar in both specimens due to fixed processing parameters. SLM Inconel 718 has moderate tensile strength (1165 MPa) and tensile elongation (11.5%), whereas SLM STS 316L has outstanding tensile strength (656 MPa) and tensile elongation (75%) compared to other SLM processed STS 316L. Fine columnar diameter (0.5 µm) and dense microstructures (porosity: 0.35%) in SLM STS 316L promoted the enhancement of tensile elongation by suitable processing condition. Fractographic analysis suggested that the lack of fusion pore with unmelted powder should be avoided to increase tensile properties by controlling processing parameters.

Microstructural Evolution of Al-Zn-Mg-Cu Alloys in Accordance with Homogenization Time.

The microstructural evolution of Al-Zn-Mg-Cu alloys has been investigated for the homogenization time effect on the texture, grain orientation and dislocation density. The Al-Zn-Mg-Cu alloys were casted and homogenized for 4, 8, 16 and 24 hours. Electron backscatter diffraction (EBSD) analysis was conducted to characterize the microstructural behavior. Micropillars were fabricated using focused ion beam (FIB) milling in grains of specific crystallographic orientations. Coarse precipitations in the grain boundaries are S (Al2CuMg) and T (Al2Mg3Zn3) phases verified by scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) observation. With increasing homogenization time, equiaxed cell sizes increased. The volume fraction of S and T phases decreased with the diffusion of atomic elements into matrix. The Vickers hardness and tensile strength values decreased with homogenization temperature. The micropillar compression analysis was compared to macro tensile test results to understand the size effect and strain burst phenomenon on the mechanical properties of Al-Zn-Mg-Cu alloys.

Effects of Nitrogen and Tensile Direction on Stress Corrosion Cracking Susceptibility of Ni-Free FeCrMnC-Based Duplex Stainless Steels.

Stress corrosion cracking (SCC) behavior of Ni-free duplex stainless steels containing N and C (Febalance-19Cr-8Mn-0.25C-(0.03, 0.21)N, in wt %) was investigated by using a slow strain rate test (SSRT) in air and aqueous NaCl solution with different tensile directions, including parallel (longitudinal) and perpendicular (transverse) to the rolling direction. It was found that alloying N was effective in increasing the resistance to SCC, while it was higher along the longitudinal direction than the transverse direction. The SCC susceptibility of the two alloys was assessed based on the electrochemical resistance to pitting corrosion, the corrosion morphology, and the fractographic analysis.

Increasing strength and conductivity of Cu alloy through abnormal plastic deformation of an intermetallic compound.

The precipitation strengthening of Cu alloys inevitably accompanies lowering of their electric conductivity and ductility. We produced bulk Cu alloys arrayed with nanofibers of stiff intermetallic compound through a precipitation mechanism using conventional casting and heat treatment processes. We then successfully elongated these arrays of nanofibers in the bulk Cu alloys to 400% of original length without breakage at room temperature using conventional rolling process. By inducing such an one-directional array of nanofibers of intermetallic compound from the uniform distribution of fine precipitates in the bulk Cu alloys, the trade-off between strength and conductivity and between strength and ductility could be significantly reduced. We observed a simultaneous increase in electrical conductivity by 1.3 times and also tensile strength by 1.3 times in this Cu alloy bulk compared to the conventional Cu alloys.

Nanostructured bulk copper fabricated by accumulative roll bonding.

In this study, we tried to fabricate the nanostructured bulk copper alloys by a severe plastic deformation process. The sheets of copper alloys (OFC, PMC90, and DLP) were heavily deformed to an equivalent strain of 6.4 by the accumulative roll-bonding (ARB) process. The microstructure and the mechanical property of the fabricated specimens were systematically investigated. The microstructure was finely subdivided with increasing the equivalent strain by the ARB process. The severely deformed copper alloys exhibited the ultrafine lamellar boundary structure where the mean lamella spacing was about 200 nm. The strength significantly increased with decreasing the lamella spacing in the ARB processed copper alloys. Especially, the tensile strength of the DLP alloys ARB processed by 8 cycles (the equivalent strain of 6.4) reached to 520 MPa, which was about three times higher than that of same materials with conventional grain size of 10-100 microm. On the other hand, the total elongation greatly dropped only by 1 ARB cycle corresponding to an equivalent strain of 0.8, which was around 3%. However, the total elongation increased again with increasing the number of the ARB cycle, and it reached to 10% after 8 cycles. The recovery of the total elongation could be recognized in all studied copper alloys. The obtained stress-strain curves showed that the improvement of the total elongation was caused by the increase in the post-uniform elongation. It can be concluded that the nanostructured copper alloys sheets having high strength without a large loss of ductility could be fabricated by the ARB process.