Design parameter estimations for adjustable bubble size in bubble generating system.

In this study, we developed a customized low cost and low energy bubble generator that can control bubble size. Hence, it can be used not only in the water treatment process but also in various other processes. This device was able to generate bubbles with a very simple system using only a general pump and a mixing chamber. Increasing the number of partition walls in the mixing chamber reduced the bubble size. Furthermore, bubbles of a few hundred nanometers were produced by the shear stress caused by increasing the thickness of the partition wall. Although the generated sub-micron bubbles were too small for their exact size to be measured using an image analysis and particle counting method, it was possible to confirm their existence indirectly through the coalescence arising from ultrasonic irradiation. The device used in this research is simple and allows bubble size to be adjusted easily by controlling the design of the mixing chamber. Therefore, it can be applied to a water treatment process, as well as a variety of other processes.

Micro and nanobubble technologies as a new horizon for water-treatment techniques: A review.

This review article organizes the studies conducted on the areas of microbubbles and nanobubbles with a special emphasis on water treatment. The basic definitions of bubble types and their size ranges are also presented based on the explanations of different researchers. The characterization parameters with state-of-the-art measuring and analysis techniques of microbubble and nanobubble technologies are summarized. Some major applications of these technologies in water-treatment processes are reviewed and briefly discussed. Based on the reviews, various potential areas for research and bubble application gaps in water and wastewater treatment technologies are identified for further study. The article is prepared in such a way that it provides a step-by-step acquaintance to the subject matter with the objective of focusing on the application of microbubbles and nanobubbles in water-treatment technology.

Optimization of fertilization characteristics of urine by addition of Nitrosomonas europaea bio-seed.

BACKGROUND: Because of the high concentration of nutrients in human urine, its utilization as an organic fertilizer has been notable throughout history. However, the nitrogen compounds in urine are not stable. Therefore, to convert urine into a suitable fertilizer, it is important to stabilize and adjust unstable nitrogen compounds such as ammonia. Because nitrification can influence the nitrogen profile, the use of nitrifying microorganisms can be useful for stabilizing the nitrogen profile of urine. This study investigated the changes in nitrogen compounds in pure urine and examined the effect of adding Nitrosomonas europaea bio-seed solution on these changes. RESULTS: It was found that the addition of bio-seed could reduce nitrogen loss as well as the time required to stabilize the nitrogen profile. Furthermore, the optimum concentration of bio-seed (6 × 10(5) N. europaea cells L(-1) ) that not only leads to the least nutrient loss but also results in an adequate nitrate/ammonium ratio and regulates the amount of nitrate produced, thereby preventing over-fertilization, was determined. CONCLUSION: At this concentration, no dilution or dewatering is required, thus minimizing water and energy consumption. Usage of the optimum of concentration of bio-seed will also eliminate the need for inorganic chemical additives. © 2016 Society of Chemical Industry.

The Waterless Portable Private Toilet: An Innovative Sanitation Solution in Disaster Zones.

Catastrophes can occur without warning and inevitably cause short-term and long-term problems. In disaster zones, having an action plan to alleviate difficulties can reduce or prevent many long-lasting complications. One of the most critical and urgent issues is sanitation. Water, energy, personnel, transportation, and the allocation of resources in disaster areas tend to become very limited during emergencies. Sanitation systems suffer in the process, potentially leading to crises due to unsafe and unhygienic surroundings. This article explores the problems of current sanitation practices in disaster areas and identifies the essential characteristics of sustainable sanitation systems. This study also presents a plan for an innovative and sustainable sanitation system using a waterless, portable, private toilet, in addition to a procedure for collecting and disposing waste. The system is agronomic, is socially acceptable, prevents contact with human waste, and can be used for individuals or families. Environmental pollution and social problems (such as sexual harassment) can be reduced both during and after restoration.

The effect of material and flushing water type on urine scale formation.

One of the important challenges with current sanitation practices is pipe blockage in urinals caused by urine scale formation. Urinal material and flushing water type are the two most important factors affecting scale formation. This paper examines the scale formation process on different materials which are commonly used in urinal manufacturing and exposed to different urine-based aqua cultures. This study shows that urine scale formation is the greatest for carbon steel material, and the least for PVC. Additionally, material exposure to the urine-rainwater mixture resulted in the smallest amount of scale formation. Based on these results, two new methods for improving sanitation practices are proposed: (1) using PVC as production material for urinals and pipelines; and (2) using rainwater for flushing systems.

Effects of catchment, first-flush, storage conditions, and time on microbial quality in rainwater harvesting systems.

Rainwater collected from a rooftop rainwater harvesting (RWH) system is typically not considered suitable for potable uses, primarily because of poor microbial quality. The quality of stored rainwater, however, can be improved through basic design and maintenance practices during the construction and operation of an RWH system. This paper presents the microbial analysis of rainwater in two RWH systems installed at the Seoul National University Campus in South Korea. Rainwater samples were collected at different locations within each system and analyzed for total and fecal coliforms, Escherichia coli, and heterotrophic plate count bacteria. Within their storage tanks, water quality improved horizontally from inlet to outlet points, and higher quality was observed at the supply point (located about 0.5 m from the base of the tank) than at the surface or bottom of the tank. First-flush rainwater was found to be highly contaminated but rainwater quality improved following about 1 mm of precipitation. The catchment surface also had a significant effect on the quality of rainwater; samples collected from a rooftop exhibited better microbial quality than from a terrace catchment. Better water quality in underground tanks (dark storage conditions) compared to open weirs/ filters (exposed to natural light) demonstrated the importance of storage conditions. Water quality also improved with longer storage, and a decrease of 70% to 90% in microbial concentrations was observed after about 1 week of storage time. The findings of this study demonstrate that the microbial quality of harvested rainwater can be improved significantly by the adoption of proper design and maintenance guidelines such as those discussed in this paper.

Development of novel oil washing process using bubble potential energy.

Oil contaminants attached to soils were separated using the bubble energies from the bursting and coalescence. The separation efficiency increased when the rotary kilns were combined. Wastewater containing separated oil contaminants was treated with the buoyant energy of bubbles and with positively charged bubbles. The water quality of the treated wastewater was good enough for the latter to be used as recycled water for bubble generation. The separation and treatment efficiencies of the novel oil washing process developed in this study was found to be similar to that of the existing oil washing process operated under high-temperature and high-pressure conditions and with dosage of chemicals.

Silver disinfection of Pseudomonas aeruginosa and E. coli in rooftop harvested rainwater for potable purposes.

Rainwater harvesting being an alternate source in water scarce areas is becoming a common practice. Catchment contact, however, deteriorates the quality of rainwater making it unfit for potable purposes. To improve the quality of harvested rainwater, silver was used as antimicrobial agent in this study. Rainwater samples were taken from underground storage tank of a rooftop rainwater harvesting system installed in one of the buildings at Seoul National University, Seoul, South Korea. The target microorganisms (MOs) were Pseudomonas aeruginosa and Escherichia coli which were measured by using plate count method and standard MPN method, respectively. The efficiency of silver disinfection was evaluated at concentrations, ranging from 0.01 to 0.1 mg/l; the safe limit approved by WHO. The experiments were performed for 168 h with different time intervals to evaluate the parameters including inactivation rate, residual effect of silver and re-growth in both MOs at lower (i.e. 0.01-0.04 mg/l) as well as the higher concentrations of silver (i.e. 0.08-0.1 mg/l). Results showed the re-growth in both MOs was only in the case of lower concentrations of silver. The possible reason of re-growth at these concentrations of silver may be the halting of bacterial cell replication process for some time without permanent damage. The kinetics of this study suggest that higher inactivation and long term residual effect towards both MOs can be achieved with the application of silver at 0.08 mg/l or higher under safe limit.

Effects of floc and bubble size on the efficiency of the dissolved air flotation (DAF) process.

Dissolved air flotation (DAF) is a method for removing particles from water using micro bubbles instead of settlement. The process has proved to be successful and, since the 1960s, accepted as an alternative to the conventional sedimentation process for water and wastewater treatment. However, limited research into the process, especially the fundamental characteristics of bubbles and particles, has been carried out. The single collector collision model is not capable of determining the effects of particular characteristics, such as the size and surface charge of bubbles and particles. Han has published a set of modeling results after calculating the collision efficiency between bubbles and particles by trajectory analysis. His major conclusion was that collision efficiency is maximum when the bubbles and particles are nearly the same size but have opposite charge. However, experimental verification of this conclusion has not been carried out yet. This paper describes a new method for measuring the size of particles and bubbles developed using computational image analysis. DAF efficiency is influenced by the effect of the recycle ratio on various average floc sizes. The larger the recycle ratio, the higher the DAF efficiency at the same pressure and particle size. The treatment efficiency is also affected by the saturation pressure, because the bubble size and bubble volume concentration are controlled by the pressure. The highest efficiency is obtained when the floc size is larger than the bubble size. These results, namely that the highest collision efficiency occurs when the particles and bubbles are about the same size, are more in accordance with the trajectory model than with the white water collector model, which implies that the larger the particles, the higher is the collision efficiency.