ABSTRACT
Dye-sensitized solar cells (DSSCs) were assembled using natural dyes extracted from red cabbage as a sensitizer. In this work, we investigated the adsorption characteristics and the electrochemical behavior for harvesting sunlight and electron transfer in red cabbage DSSCs under different solvents and pH. For the red cabbage dye-sensitized electrode adsorbed at pH 3.5, the solar cell yields a short-circuit current density (Jsc) of 1.60 mA/cm2, a photovoltage (Vcc) of 0.46 V, and a fill factor of 0.55, corresponding to an energy conversion efficiency (η) of 0.41%.
Subject(s)
Brassica/chemistry , Coloring Agents/chemistry , Electric Power Supplies , Plant Extracts/chemistry , Solar Energy , Coloring Agents/isolation & purification , Coloring Agents/radiation effects , Electric Conductivity , Electrodes , Energy Transfer/radiation effects , Equipment Design , Equipment Failure Analysis , Hydrogen-Ion Concentration , Light , Materials Testing , Plant Extracts/radiation effectsABSTRACT
Inkjet technology has been used as manufacturing a tool for printed electronics. To increase the productivity, the jetting frequency needs to be increased. When using high-frequency jetting, the printed pattern quality could be non-uniform since the jetting performance characteristics including the jetting speed and droplet volume could vary significantly with increases in jet frequency. Therefore, high-frequency jetting behavior must be evaluated properly for improvement. However, it is difficult to measure high-frequency jetting behavior using previous vision analysis methods, because subsequent droplets are close or even merged. In this paper, we present vision measurement techniques to evaluate the drop formation of high-frequency jetting. The proposed method is based on tracking target droplets such that subsequent droplets can be excluded in the image analysis by focusing on the target droplet. Finally, a frequency sweeping method for jetting speed and droplet volume is presented to understand the overall jetting frequency effects on jetting performance.
ABSTRACT
Two natural dyes extracted from gardenia yellow (Gardenia jasminoides) and cochineal (Dactylopius coccus) were used as sensitizers in the assembly of dye-sensitized solar cells (DSSCs) to harvest light over a wide range of wavelengths. The adsorption characteristics, electrochemical properties and photovoltaic efficiencies of the natural DSSCs were investigated. The adsorption kinetics data of the dyes were obtained in a small adsorption chamber and fitted with a pseudo-second-order model. The photovoltaic performance of a photo-electrode adsorbed with single-dye (gardenia or cochineal) or the mixture or successive adsorption of the two dyes, was evaluated from current-voltage measurements. The energy conversion efficiency of the TiO2 electrode with the successive adsorption of cochineal and gardenia dyes was 0.48%, which was enhanced compared to single-dye adsorption. Overall, a double layer of the two natural dyes as sensitizers was successfully formulated on the nanoporous TiO2 surface based on the differences in their adsorption affinities of gardenia and cochineal.
Subject(s)
Carmine/chemistry , Carmine/isolation & purification , Gardenia/chemistry , Hemiptera/chemistry , Solar Energy , Titanium/chemistry , Animals , Photochemical ProcessesABSTRACT
Dye-sensitized solar cells (DSSCs) were assembled using natural dyes extracted from Monascus red pigment as a sensitizer. In this work, we studied the adsorption characteristics for harvesting sunlight and the electrochemical behavior for electron transfer in Monascus red DSSC using different solvents. The effect of polar aprotic and protic solvents including water, ethanol, and dimethylsulfoxide (DMSO) used in the sensitization process was investigated for the improvement in conversion efficiency of a cell. As for the Monascus red dye-sensitized electrode in DMSO solvent, the solar cell yields a short-circuit current density (Jsc) of 1.23mA/cm(2), a photovoltage (Voc) of 0.75V, and a fill factor of 0.72, corresponding to an energy conversion efficiency (η) of 0.66%.
Subject(s)
Coloring Agents/chemistry , Electric Power Supplies , Monascus/chemistry , Solar Energy , Coloring Agents/isolation & purification , Dimethyl Sulfoxide/chemistry , Electrochemical Techniques , Electrodes , Ethanol/chemistry , Plant Extracts/chemistry , Solvents/chemistry , Water/chemistryABSTRACT
We have successfully introduced green phosphors LaPO4:Ce, Tb (G4) or (Mg, Zn)Al11O19:Eu (G2) into TiO2 photoelectrode of dye-sensitized solar cells. The conversion efficiency of the G4-doped device was enhanced by 30% compared with the pristine TiO2 photoelectrode. The green phosphor doped at 5-wt.% ratio contributed to the reduction of resistances of the surface and interface of the photoelectrode and to the great enhancement of the absorption spectrum in UV-visible and near-infrared regions. The internal resistances and absorbance of the photoelectrode directly affect the power conversion efficiency. Green phosphor plays an important role towards the realization of high-efficiency dye-sensitized solar cells.
