Photoluminescence Redistribution of InGaN Nanowires Induced by Plasmonic Silver Nanoparticles.

Hybrid nanostructures based on InGaN nanowires with decorated plasmonic silver nanoparticles are investigated in the present study. It is shown that plasmonic nanoparticles induce the redistribution of room temperature photoluminescence between short-wavelength and long-wavelength peaks of InGaN nanowires. It is defined that short-wavelength maxima decreased by 20%, whereas the long-wavelength maxima increased by 19%. We attribute this phenomenon to the energy transfer and enhancement between the coalesced part of the NWs with 10-13% In content and the tips above with an In content of about 20-23%. A proposed Fröhlich resonance model for silver NPs surrounded by a medium with refractive index of 2.45 and spread 0.1 explains the enhancement effect, whereas the decreasing of the short-wavelength peak is associated with the diffusion of charge carriers between the coalesced part of the NWs and the tips above.

Free surface entrainment of oxide particles and their role in ultrasonic treatment performance of aluminum alloys.

Although the ultrasonic treatment of molten aluminum has been studied for long period, there is still much to be revealed for this process. Many studies have focused on the investigation of acoustic cavitation and streaming under the horn tip and their effects on the treatment efficiency. However, to the best of our knowledge, no attempt has been done to explain phenomena occurring near or on the melt free surface. Thus, the goal of this study is to investigate phenomena occurring at the free surface during ultrasound irradiation and clarify their possible influence on the ultrasound treatment performance. The results of high temperature and water model experiments reveal that ultrasound irradiation significantly promotes the formation of alumina particles on the melt free surface around sonotrode, and part of these particles can be entrained into aluminum melts. Furthermore, TEM observation results suggested that the entrained alumina inclusions can serve as nucleation sites for the primary Al3Zr compounds. Most importantly, the oxidation and entrainment of particles from free surface are likely to be controllable by the immersion depth of sonotrode into molten aluminum.

Fabrication of CrSi2-Containing Master Alloys for Modification of Fe-Containing Intermetallic Compounds in Aluminum Alloys.

Aluminum contaminations, particularly iron, present a serious challenge to aluminum recycling technology. This is why many studies have focused on the reduction of detrimental effects of iron-containing contaminations through addition of elements such as manganese and chromium. However, the desirable modifying effect is often difficult to achieve because it would require concentrations of added elements greater than the allowable limits for many aluminum alloys. Thus, an alternative way to obtain the modifying effect, by using a much smaller amount of the modifying elements which are added to the aluminum melt as solid particles, was proposed in this study. The main goal of the present study was to investigate the possibilities of fabricating an aluminum master alloy by adding CrSi2 particles onto the surface of the vortex formed during mechanical agitation of molten aluminum. Two kinds of CrSi2 powder were used: one was commercial powder, and the other was self-synthesized CrSi2 via mechanical alloying by planetary ball milling. The results revealed that CrSi2 particles with a larger size penetrate the melt better. Particles of three kinds were found to exist in the Al melt after the addition of CrSi2 powder: (1) inclusions of eutectic origin formed at the last stage of crystallization, (2) mixtures of Al-Cr compounds and original CrSi2 particles and (3) original CrSi2 particles. Low melt temperatures and short treatment times were found to favor the fabrication of master alloys because they impeded the dissolution of CrSi2 particles into the Al melt and, thus, allowed one to fabricate the master alloy containing the particles of the second and third types.

Positron Emission Tomography (PET) for Molecular Plant Imaging.

Positron emission tomography (PET) is an imaging technology that measures 3D spatial distribution and kinetics of radio-tagged biomolecules in a living subject quantitatively and nondestructively. Commonly used positron-emitting radionuclides include 11C, 13N, and 15O, which are essential elements for plant growth. Combining radiotracer techniques with PET, this in vivo molecular imaging capability offers plant biologists a powerful tool for molecular phenotyping research. While PET is widely used clinically for cancer diagnosis and pre-clinically for drug development, it is an unfamiliar imaging tool for plant biologists. This chapter introduces the basic principles of PET, factors that affect the quantitative accuracy of PET when imaging plants, and techniques for administering radiotracers to plants for a variety of molecular plant imaging applications.

Effect of gas injection on cavitation-assisted plasma treatment efficiency of wastewater.

Underwater plasma has been long recognized as a "green" alternative to conventional chemicals in the wastewater treatment processes. However, practical application of underwater plasma is still challenging due to insufficient treatment performance. Recently, we proposed a novel process named ACAP utilizing acoustic cavitation in order to stabilize the plasma generation and to enlarge the plasma processing region. This work continues our investigation regarding the ACAP treatment process focusing on effects of gas injection. Experiments were performed using an ultrasonic installation equipped with a specially designed sonotrode (Diam. 48 mm) operated at a frequency of 20 kHz and acoustic power of 120 W. The results revealed that the degradation efficiency of Rhodamine B, which was used as a model wastewater pollutant, remains almost unchangeable in the case of air injection, but it is doubled when argon is injected into the ACAP reactor. It was found that the argon injection enhances the degradation efficiency significantly even without ultrasound irradiation. Results of additional measurements suggest that the effect of argon is attributed to its ability to yield high temperature during cavitation, comparatively good solubility in water and a better ability to reduce the breakdown voltage in water compared to the air case.

Enhancement of oscillation amplitude of cavitation bubble due to acoustic wake effect in multibubble environment.

Acoustic cavitation occurs in ultrasonic treatment causing various phenomena such as chemical synthesis, chemical decomposition, and emulsification. Nonlinear oscillations of cavitation bubbles are assumed to be responsible for these phenomena, and the neighboring bubbles may interact each other. In the present study, we numerically investigated the dynamic behavior of cavitation bubbles in multi-bubble systems. The results reveal that the oscillation amplitude of a cavitation bubble surrounded by other bubbles in a multi-bubble system becomes larger compared with that in the single-bubble case. It is found that this is caused by an acoustic wake effect, which reduces the pressure near a bubble surrounded by other bubbles and increases the time delay between the bubble contraction/expansion cycles and sound pressure oscillations. A new parameter, called "cover ratio" is introduced to quantitatively evaluate the variation in the bubble oscillation amplitude, the time delay, and the maximum bubble radius.

Incorporation of Powder Particles into an Impeller-Stirred Liquid Bath through Vortex Formation.

The present study addresses the incorporation of fine particles into liquids via the creation of a large-scale swirling vortex on the liquid free surface using a rotary impeller positioned along the axis of a cylindrical vessel. Four types of particles are used in the experiments to investigate the incorporation efficiency of the particles into a water bath under different impeller rotation speeds. Additionally, the vortex characteristics are investigated numerically. The results reveal that two factors, namely the particle wettability and turbulent oscillations at the bottom part of vortex surface, play dominant roles in determining the particle incorporation behavior. Hydrophobic particles are incapable of being incorporated into the water bath under any of the conditions examined in the present study. Partly wettable particles are entrained into the water bath, with the efficiency increasing with the impeller rotation speed and particle size. This is because an increase in the impeller rotation speed causes vortex deformation, whereby its bottom part approaches the impeller blades where the turbulent surface oscillations reach maximum amplitudes. Another possible mechanism of particle incorporation is the effect of capillary increases of liquid into the spaces between particles, which accumulate on the bottom surface of the vortex.

High-speed imaging of ultrasonic emulsification using a water-gallium system.

Aiming at elucidating ultrasonic emulsification mechanisms, the interaction between a single or multiple acoustic cavitation bubbles and gallium droplet interface was investigated using an high-speed imaging technique. To our best knowledge, the moment of emulsification and formation of fine droplets during ultrasound irradiation were observed for the first time. It was found that the detachment of fine gallium droplets occurs from the water-gallium interface during collapse of big cavitation bubbles. The results suggest that the maximum size of cavitation bubble before collapsing is of prime importance for emulsification phenomena. Previous numerical simulation revealed that the collapse of big cavitation bubble is followed by generation of high-velocity liquid jet directed toward the water-gallium interface. Such a jet is assumed to be the prime cause of liquid emulsification. The distance between cavitation bubbles and water-gallium interface was found to slightly affect the emulsification onset. The droplet fragmentation conditions are also discussed in terms of the balance between (1) interfacial and kinetic energies and (2) dynamic and Laplace pressure during droplet formation.

Characterization of acoustic streaming in water and aluminum melt during ultrasonic irradiation.

It is well known that ultrasonic cavitation causes a steady flow termed acoustic streaming. In the present study, the velocity of acoustic streaming in water and molten aluminum is measured. The method is based on the measurement of oscillation frequency of Karman vortices around a cylinder immersed into liquid. For the case of acoustic streaming in molten metal, such measurements were performed for the first time. Four types of experiments were conducted in the present study: (1) Particle Image Velocimetry (PIV) measurement in a water bath to measure the acoustic streaming velocity visually, (2) frequency measurement of Karman vortices generated around a cylinder in water, and (3) in aluminum melt, and (4) cavitation intensity measurements in molten aluminum. Based on the measurement results (1) and (2), the Strouhal number for acoustic streaming was determined. Then, using the same Strouhal number and measuring oscillation frequency of Karman vortices in aluminum melt, the acoustic streaming velocity was measured. The velocity of acoustic streaming was found to be independent of amplitude of sonotrode tip oscillation both in water and aluminum melt. This can be explained by the effect of acoustic shielding and liquid density.

Combined effect of acoustic cavitation and pulsed discharge plasma on wastewater treatment efficiency in a circulating reactor: A case study of Rhodamine B.

The present study investigates the wastewater treatment performance of an acoustic cavitation assisted plasma (ACAP) process in a circulating reactor using Rhodamine B (RhB) as a model water pollution. The concept of this process was proposed by the authors recently for a batch type rector. The measurements revealed that combining the ultrasound irradiation with pulsed discharge plasma allows the RhB degradation efficiency to be drastically increased as compared with the plasma-alone case. This effect is especially significant at higher values of solution electrical conductivity examined in a range of 20 ~ 400 µS/cm. Acidic conditions and larger flow rates of solution were found to be favorable for the degradation efficiency. The effect of flow rate was also analyzed through numerical simulation. The results indicated that the mass transfer of RhB to the plasma-cavitation zone is one of the controlling parameters influencing the degradation performance. Behavior of bubbles and pulse discharge frequency were examined using a high-speed video camera. Relatively large bubbles were found to favor the plasma pulse generation and propagation when move near the high-voltage electrode. On the whole, the results of this study suggest that the ACAP process has the potential to synergistically extend the application area of underwater plasma in both research and industry.

Seasonal nitrogen remobilization and the role of auxin transport in poplar trees.

Seasonal nitrogen (N) cycling in Populus, involves bark storage proteins (BSPs) that accumulate in bark phloem parenchyma in the autumn and decline when shoot growth resumes in the spring. Little is known about the contribution of BSPs to growth or the signals regulating N remobilization from BSPs. Knockdown of BSP accumulation via RNAi and N sink manipulations were used to understand how BSP storage influences shoot growth. Reduced accumulation of BSPs delayed bud break and reduced shoot growth following dormancy. Further, 13N tracer studies also showed that BSP accumulation is an important factor in N partitioning from senescing leaves to bark. Thus, BSP accumulation has a role in N remobilization during N partitioning both from senescing leaves to bark and from bark to expanding shoots once growth commences following dormancy. The bark transcriptome during BSP catabolism and N remobilization was enriched in genes associated with auxin transport and signaling, and manipulation of the source of auxin or auxin transport revealed a role for auxin in regulating BSP catabolism and N remobilization. Therefore, N remobilization appears to be regulated by auxin produced in expanding buds and shoots that is transported to bark where it regulates protease gene expression and BSP catabolism.

Non-medical Use of Naphazoline (Naphthyzin): Two Case Reports.

: The paper describes 2 case reports of non-medical use of Naphazoline (Naphthyzin). Both demonstrate that the peripherally acting alpha-adrenergic agonist Naphazoline obtains some addictive potential. The drug produces a feeling of euphoria, which resembles the perceived effects of psychostimulants. Both patients and people who consume Naphazoline for intoxication report increased tolerance after repeated use which indicates the addictive potential of the substance. To the best of our knowledge, this is the first examination of non-medical Naphazoline use and the first attempt to describe its addictive potential. Clinical psychiatrists should be aware of this phenomenon when addressing polysubstance use behavior.

Mechanisms and Treatment of Light-Induced Retinal Degeneration-Associated Inflammation: Insights from Biochemical Profiling of the Aqueous Humor.

Ocular inflammation contributes to the pathogenesis of blind-causing retinal degenerative diseases, such as age-related macular degeneration (AMD) or photic maculopathy. Here, we report on inflammatory mechanisms that are associated with retinal degeneration induced by bright visible light, which were revealed while using a rabbit model. Histologically and electrophysiologically noticeable degeneration of the retina is preceded and accompanied by oxidative stress and inflammation, as evidenced by granulocyte infiltration and edema in this tissue, as well as the upregulation of total protein, pro-inflammatory cytokines, and oxidative stress markers in aqueous humor (AH). Consistently, quantitative lipidomic studies of AH elucidated increase in the concentration of arachidonic (AA) and docosahexaenoic (DHA) acids and lyso-platelet activating factor (lyso-PAF), together with pronounced oxidative and inflammatory alterations in content of lipid mediators oxylipins. These alterations include long-term elevation of prostaglandins, which are synthesized from AA via cyclooxygenase-dependent pathways, as well as a short burst of linoleic acid derivatives that can be produced by both enzymatic and non-enzymatic free radical-dependent mechanisms. The upregulation of all oxylipins is inhibited by the premedication of the eyes while using mitochondria-targeted antioxidant SkQ1, whereas the accumulation of prostaglandins and lyso-PAF can be specifically suppressed by topical treatment with cyclooxygenase inhibitor Nepafenac. Interestingly, the most prominent antioxidant and anti-inflammatory benefits and overall retinal protective effects are achieved by simultaneous administrating of both drugs indicating their synergistic action. Taken together, these findings provide a rationale for using a combination of mitochondria-targeted antioxidant and cyclooxygenase inhibitor for the treatment of inflammatory components of retinal degenerative diseases.

X-ray CT in Phase Contrast Enhancement Geometry of Alginate Microbeads in a Whole-Animal Model.

Imaging soft biomaterials in vivo is a significant challenge, as most conventional techniques are limited by biomaterial contrast, penetration depth, or spatial resolution. Exogeneous contrast agents used to increase contrast may also alter material properties or exhibit local toxicity. The capability to observe biomaterial constructs in vivo without introducing exogenous contrast would improve preclinical testing and evaluation. Conventional X-ray Computed Tomography allows fast, high-resolution imaging at high penetration depth, but biomaterial contrast is low. Previous studies employing X-ray phase contrast (XPC) and utilizing a synchrotron source provided support for the significant potential of XPC in imaging biomaterials without contrast agents. In this study, XPC tomography was used to image alginate hydrogel microspheres within a small animal omental pouch model using a commercially available X-ray source. Multilayer microbeads could be identified in the XPC images with volumetric and structural information not possible in histological analysis. The number of microbeads present and microbead volume and diameter could be quantified from the images. The results of this study show that XPC tomography can be a useful tool for monitoring of implanted soft biomaterials in small animal models.

Liquid jet directionality and droplet behavior during emulsification of two liquids due to acoustic cavitation.

The present study numerically investigates liquid-jet characteristics of acoustic cavitation during emulsification in water/gallium/air and water/silicone oil/air systems. It is found that a high-speed liquid jet is generated when acoustic cavitation occurs near a minute droplet of one liquid in another. The velocity of liquid jet significantly depends on the ultrasonic pressure monotonically increasing as the pressure amplitude increases. Also, the initial distance between cavitation bubble and liquid droplet affects the jet velocity significantly. The results revealed that the velocity takes maximum values when the initial distance between the droplet and cavitation bubble is moderate. Surprisingly, the liquid jet direction was found to depend on the droplet properties. Specifically, the direction of liquid jet is toward the droplet in the case of water/gallium/air system, and vice versa the jet is directed from the droplet in the case of water/silicone oil/air system. The jet directionality can be explained by location of the high-pressure spot generated during the bubble contraction.

Role of Acoustic Streaming in Formation of Unsteady Flow in Billet Sump during Ultrasonic DC Casting of Aluminum Alloys.

The present work investigated melt flow pattern and temperature distribution in the sump of aluminum billets produced in a hot-top equipped direct chilling (DC) caster conventionally and with ultrasonic irradiation. The main emphasis was placed on clarifying the effects of acoustic streaming and hot-top unit type. Acoustic streaming characteristics were investigated first by using the earlier developed numerical model and water model experiments. Then, the acoustic streaming model was applied to develop a numerical code capable of simulating unsteady flow phenomena in the sump during the DC casting process. The results revealed that the introduction of ultrasonic vibrations into the melt in the hot-top unit had little or no effect on the temperature distribution and sump profile, but had a considerable effect on the melt flow pattern in the sump. Our results showed that ultrasound irradiation makes the flow velocity faster and produces a lot of relatively small eddies in the sump bulk and near the mushy zone. The latter causes frequently repeated thinning of the mushy zone layer. The numerical predictions were verified against measurements performed on a pilot DC caster producing 203 mm billets of Al-17%Si alloy. The verification revealed approximately the same sump depth and shape as those in the numerical simulations, and confirms the frequent and large fluctuations of the melt temperature during ultrasound irradiation. However, the measured temperature distribution in the sump significantly differed from that predicted numerically. This suggests that the present mathematical model should be further improved, particularly in terms of more accurate descriptions of boundary conditions and mushy zone characteristics.

Fragmentation of cavitation bubble in ultrasound field under small pressure amplitude.

In the present study, dynamic behavior and fragmentation mechanism of acoustic cavitation bubbles are investigated under relatively small pressure amplitudes of ultrasonic wave through a three-dimensional compressive multiphase flow simulation and experimental observations. It is found that the oscillating bubble takes a non-spherical shape soon after occurring the Rayleigh collapse following the sound pressure distribution around the bubble. Then, the amplitude of non-spherical deformation is enhanced during small high-frequent oscillations after the Rayleigh collapse due to the fluid inertial effect. Finally, the oscillating bubble is fragmented into two smaller ones with the Laplace pressure gradient becoming the final trigger of bubble fragmentation. Besides, the results reveal that the temperature of bubble surface is varied when the non-spherical bubble deformation is large, while during spherical bubble oscillations the surface temperature remains almost unchanged.

Cherenkov luminescence imaging of shallow sources in semitransparent media.

We experimentally investigated the Cherenkov luminescence imaging (CLI) of the isotopes with different beta particles energies (Cu64, F18, Au198, P32, and Br76) in semitransparent biological equivalent media. The main focus of this work is to characterize the CLI when the sources are at the depth comparable with the range of beta particles. The experimental results were compared with Monte Carlo (MC) simulation results to fine tune the simulation parameters to better model the phantom materials. This approach can be applied to estimate the CLI performance for different phantom materials and isotopes. This work also demonstrates some unique properties of high energy beta particles that can be beneficial for CLI, including the possibility to utilize the betas escaped from the object for imaging purposes.

Feasibility study of a point-of-care positron emission tomography system with interactive imaging capability.

PURPOSE: We investigated the feasibility of a novel positron emission tomography (PET) system that provides near real-time feedback to an operator who can interactively scan a patient to optimize image quality. The system should be compact and mobile to support point-of-care (POC) molecular imaging applications. In this study, we present the key technologies required and discuss the potential benefits of such new capability. METHODS: The core of this novel PET technology includes trackable PET detectors and a fully three-dimensional, fast image reconstruction engine implemented on multiple graphics processing units (GPUs) to support dynamically changing geometry by calculating the system matrix on-the-fly using a tube-of-response approach. With near real-time image reconstruction capability, a POC-PET system may comprise a maneuverable front PET detector and a second detector panel which can be stationary or moved synchronously with the front detector such that both panels face the region-of-interest (ROI) with the detector trajectory contoured around a patient's body. We built a proof-of-concept prototype using two planar detectors each consisting of a photomultiplier tube (PMT) optically coupled to an array of 48 × 48 lutetium-yttrium oxyorthosilicate (LYSO) crystals (1.0 × 1.0 × 10.0 mm3 each). Only 38 × 38 crystals in each arrays can be clearly re-solved and used for coincidence detection. One detector was mounted to a robotic arm which can position it at arbitrary locations, and the other detector was mounted on a rotational stage. A cylindrical phantom (102 mm in diameter, 150 mm long) with nine spherical lesions (8:1 tumor-to-background activity concentration ratio) was imaged from 27 sampling angles. List-mode events were reconstructed to form images without or with time-of-flight (TOF) information. We conducted two Monte Carlo simulations using two POC-PET systems. The first one uses the same phantom and detector setup as our experiment, with the detector coincidence re-solving time (CRT) ranging from 100 to 700 ps full-width-at-half-maximum (FWHM). The second study simulates a body-size phantom (316 × 228 × 160 mm3 ) imaged by a larger POC-PET system that has 4 × 6 modules (32 × 32 LYSO crystals/module, four in axial and six in transaxial directions) in the front panel and 3 × 8 modules (16 × 16 LYSO crystals/module, three in axial and eight in transaxial directions) in the back panel. We also evaluated an interactive scanning strategy by progressively increasing the number of data sets used for image reconstruction. The updated images were analyzed based on the number of data sets and the detector CRT. RESULTS: The proof-of-concept prototype re-solves most of the spherical lesions despite a limited number of coincidence events and incomplete sampling. TOF information reduces artifacts in the reconstructed images. Systems with better timing resolution exhibit improved image quality and reduced artifacts. We observed a reconstruction speed of 0.96 × 106 events/s/iteration for 600 × 600 × 224 voxel rectilinear space using four GPUs. A POC-PET system with significantly higher sensitivity can interactively image a body-size object from four angles in less than 7 min. CONCLUSIONS: We have developed GPU-based fast image reconstruction capability to support a PET system with arbitrary and dynamically changing geometry. Using TOF PET detectors, we demonstrated the feasibility of a PET system that can provide timely visual feedback to an operator who can scan a patient interactively to support POC imaging applications.