Investigation of the Effect of Double-Filler Atoms on the Thermoelectric Properties of Ce-YbCo4Sb12.

Skutterudite compounds have been studied as potential thermoelectric materials due to their high thermoelectric efficiency, which makes them attractive candidates for applications in thermoelectric power generation. In this study, the effects of double-filling on the thermoelectric properties of the CexYb0.2-xCo4Sb12 skutterudite material system were investigated through the process of melt spinning and spark plasma sintering (SPS). By replacing Yb with Ce, the carrier concentration was compensated for by the extra electron from Ce donors, leading to optimized electrical conductivity, Seebeck coefficient, and power factor of the CexYb0.2-xCo4Sb12 system. However, at high temperatures, the power factor showed a downturn due to bipolar conduction in the intrinsic conduction regime. The lattice thermal conductivity of the CexYb0.2-xCo4Sb12 skutterudite system was clearly suppressed in the range between 0.025 and 0.1 for Ce content, due to the introduction of the dual phonon scattering center from Ce and Yb fillers. The highest ZT value of 1.15 at 750 K was achieved for the Ce0.05Yb0.15Co4Sb12 sample. The thermoelectric properties could be further improved by controlling the secondary phase formation of CoSb2 in this double-filled skutterudite system.

Flexible Heater Fabrication Using Amino Acid-Based Ink and Laser-Direct Writing.

Nature's systems have evolved over a long period to operate efficiently, and this provides hints for metal nanoparticle synthesis, including the enhancement, efficient generation, and transport of electrons toward metal ions for nanoparticle synthesis. The organic material-based ink composed of the natural materials used in this study requires low laser power for sintering compared to conventional nanoparticle ink sintering. This suggests applicability in various and sophisticated pattern fabrication applications without incurring substrate damage. An efficient electron transfer mechanism between amino acids (e.g., tryptophan) enables silver patterning on flexible polymer substrates (e.g., PET) by laser-direct writing. The reduction of silver ions to nanoparticles was induced and sintered by simultaneous photo/thermalchemical reactions on substrates. Furthermore, it was possible to fabricate a stable, transparent, and flexible heater that operates under mechanical deformation.

NaCl Ionization-Based Moisture Sensor Prepared by Aerosol Deposition for Monitoring Respiratory Patterns.

A highly polarizable moisture sensor with multimodal sensing capabilities has great advantages for healthcare applications such as human respiration monitoring. We introduce an ionically polarizable moisture sensor based on NaCl/BaTiO3 composite films fabricated using a facile aerosol deposition (AD) process. The proposed sensing model operates based on an enormous NaCl ionization effect in addition to natural moisture polarization, whereas all previous sensors are based only on the latter. We obtained an optimal sensing performance in a 0.5 µm-thick layer containing NaCl-37.5 wt% by manipulating the sensing layer thickness and weight fraction of NaCl. The NaCl/BaTiO3 sensing layer exhibits outstanding sensitivity over a wide humidity range and a fast response/recovery time of 2/2 s; these results were obtained by performing the one-step AD process at room temperature without using any auxiliary methods. Further, we present a human respiration monitoring system using a sensing device that provides favorable and stable electrical signals under diverse respiratory scenarios.

Fabrication of Large-Area Mullite-Cordierite Composite Substrates for Semiconductor Probe Cards and Enhancement of Their Reliability.

This work aims to fabricate a large-area ceramic substrate for the application of probe cards. Mullite (M) and cordierite (C), which both have a low thermal expansion coefficient, excellent resistance to thermal shock, and high durability, were selected as starting powders. The mullite-cordierite composites were produced through different composition ratios of starting powders (M:C = 100:0, M:C = 90:10, M:C = 70:30, M:C = 50:50, M:C = 30:70, and M:C = 0:100). The effects of composition ratio and sintering temperature on the density, porosity, thermal expansion coefficient, and flexural strength of the mullite-cordierite composite pellets were investigated. The results showed that the mullite-cordierite composite pellet containing 70 wt% mullite and 30 wt% cordierite sintered at 1350 °C performed exceptionally well. Based on these findings, a large-area mullite-cordierite composite substrate with a diameter of 320 mm for use in semiconductor probe cards was successfully fabricated. Additionally, the changes in sheet resistance and flexural strength were measured to determine the effect of the environmental tests on the large-area substrate such as damp heat and thermal shock. The results indicated that the mullite-cordierite composite substrate was extremely reliable and durable.

Thermoelectric Properties of Cu2Te Nanoparticle Incorporated N-Type Bi2Te2.7Se0.3.

To develop highly efficient thermoelectric materials, the generation of homogeneous heterostructures in a matrix is considered to mitigate the interdependency of the thermoelectric compartments. In this study, Cu2Te nanoparticles were introduced onto Bi2Te2.7Se0.3 n-type materials and their thermoelectric properties were investigated in terms of the amount of Cu2Te nanoparticles. A homogeneous dispersion of Cu2Te nanoparticles was obtained up to 0.4 wt.% Cu2Te, whereas the Cu2Te nanoparticles tended to agglomerate with each other at greater than 0.6 wt.% Cu2Te. The highest power factor was obtained under the optimal dispersion conditions (0.4 wt.% Cu2Te incorporation), which was considered to originate from the potential barrier on the interface between Cu2Te and Bi2Te2.7Se0.3. The Cu2Te incorporation also reduced the lattice thermal conductivity, and the dimensionless figure of merit ZT was increased to 0.75 at 374 K for 0.4 wt.% Cu2Te incorporation compared with that of 0.65 at 425 K for pristine Bi2Te2.7Se0.3. This approach could also be an effective means of controlling the temperature dependence of ZT, which could be modulated against target applications.

Green Synthesis of Nanoparticles Using Bio-Inspired Systems and Electrically Conductive Pattern Fabrication through Laser-Direct Writing.

Systems existing in nature have evolved to operate efficiently over a long period of time, enabling efficient material transformation and processing. These natural systems provide hints for the synthesis of metal nanoparticles through efficient electron generation and transport towards metal ions for the reduction process. In this study, based on the efficient electron transfer mechanism between tryptophan (Trp) in the living body, the possibility of advanced silver patterning on flexible substrates has been presented through laser-direct writing. Irradiation of a low-power laser on the precursor induces the reduction of silver ions to nanoparticles. The sintering of these generated nanoparticles induces a silver conductive pattern by a photothermal/chemical reaction. The method of this study has strength as it supports the possibility of conductive pattern fabrication on various substrates (e.g., glass and PDMS) using a silver-based organic ink with low laser power compared to the conventional nanoparticle-based sintering method. It also suggests its suitability to various applications in terms of sophisticated pattern fabrication with minimized substrate denaturation.

Enhanced Production of Bacterial Cellulose from Miscanthus as Sustainable Feedstock through Statistical Optimization of Culture Conditions.

Biorefineries are attracting attention as an alternative to the petroleum industry to reduce carbon emissions and achieve sustainable development. In particular, because forests play an important role in potentially reducing greenhouse gas emissions to net zero, alternatives to cellulose produced by plants are required. Bacterial cellulose (BC) can prevent deforestation and has a high potential for use as a biomaterial in various industries such as food, cosmetics, and pharmaceuticals. This study aimed to improve BC production from lignocellulose, a sustainable feedstock, and to optimize the culture conditions for Gluconacetobacter xylinus using Miscanthus hydrolysates as a medium. The productivity of BC was improved using statistical optimization of the major culture parameters which were as follows: temperature, 29 °C; initial pH, 5.1; and sodium alginate concentration, 0.09% (w/v). The predicted and actual values of BC production in the optimal conditions were 14.07 g/L and 14.88 g/L, respectively, confirming that our prediction model was statistically significant. Additionally, BC production using Miscanthus hydrolysates was 1.12-fold higher than in the control group (commercial glucose). Our result indicate that lignocellulose can be used in the BC production processes in the near future.

Development of Colorimetric Whole-Cell Biosensor for Detection of Heavy Metals in Environment for Public Health.

Heavy metals cause various fetal diseases in humans. Heavy metals from factory wastewater can contaminate drinking water, fish, and crops. Inductively coupled plasma-mass spectrometry (ICP-MS) and atomic absorption spectrometry (AAS) are commonly used to analyze heavy metal contents; however, these methods require pre-treatment processes and are expensive and complex. To overcome these limitations, three metal-sensing materials using a whole-cell biosensor in Escherichia coli (E. coli) were developed. Strains were engineered to harbor three kinds of plasmids containing the copA, zntA, and mer promoters for sensing copper, cadmium, and mercury, respectively. The luciferase (lux) gene was inserted as a reporter into the plasmid, which was later replaced with a fused protein sequence containing OmpA (1-159) and mCherry for optical detection. The constructed strains could detect mercury, cadmium, and copper at 0.1-0.75 ppm, 0.2-0.75 ppm, and 2-7.5 ppm, respectively, with linearity values of 0.99030, 0.99676, and 0.95933, respectively. The immobilization linearity value was 0.99765. Notably, these three heavy metals could be detected by visual analysis of the strains. Overall, these findings establish this novel sensor as a potential approach for heavy metal detection in biological samples and foods.

Effect of Gas Annealing on the Electrical Properties of Ni/AlN/SiC.

It is shown in this work that annealing of Schottky barrier diodes (SBDs) in the form of Ni/AlN/SiC heterojunction devices in an atmosphere of nitrogen and oxygen leads to a significant improvement in the electrical properties of the structures. Compared to the non-annealed device, the on/off ratio of the annealed SBD devices increased by approximately 100 times. The ideality factor, derived from the current-voltage (IV) characterization, decreased by a factor of ~5.1 after annealing, whereas the barrier height increased from ~0.52 to 0.71 eV. The bonding structure of the AlN layer was characterized by X-ray photoelectron spectroscopy. Examination of the N 1 s and O 1 s peaks provided direct indication of the most prevalent chemical bonding states of the elements.

Improved Electrical Characteristics of Gallium Oxide/P-Epi Silicon Carbide Static Induction Transistors with UV/Ozone Treatment Fabricated by RF Sputter.

In this study, static induction transistors (SITs) with beta gallium oxide (ß-Ga2O3) channels are grown on a p-epi silicon carbide (SiC) layer via radio frequency sputtering. The Ga2O3 films are subjected to UV/ozone treatment, which results in reduced oxygen vacancies in the X-ray photoelectron spectroscopy data, lower surface roughness (3.51 nm) and resistivity (319 Ω·cm), and higher mobility (4.01 cm2V-1s-1). The gate leakage current is as low as 1.0 × 10-11 A at VGS = 10 V by the depletion layer formed between n-Ga2O3 and p-epi SiC at the gate region with a PN heterojunction. The UV/O3-treated SITs exhibit higher (approximately 1.64 × 102 times) drain current (VDS = 12 V) and on/off ratio (4.32 × 105) than non-treated control devices.

Classification of Standing and Walking States Using Ground Reaction Forces.

The operation of wearable robots, such as gait rehabilitation robots, requires real-time classification of the standing or walking state of the wearer. This report explains a technique that measures the ground reaction force (GRF) using an insole device equipped with force sensing resistors, and detects whether the insole wearer is standing or walking based on the measured results. The technique developed in the present study uses the waveform length that represents the sum of the changes in the center of pressure within an arbitrary time window as the determining factor, and applies this factor to a conventional threshold method and an artificial neural network (ANN) model for classification of the standing and walking states. The results showed that applying the newly developed technique could significantly reduce classification errors due to shuffling movements of the patient, typically noticed in the conventional threshold method using GRF, i.e., real-time classification of the standing and walking states is possible in the ANN model. The insole device used in the present study can be applied not only to gait analysis systems used in wearable robot operations, but also as a device for remotely monitoring the activities of daily living of the wearer.

Influence of Gas Annealing on Sensitivity of AlN/4H-Sic-Based Temperature Sensors.

In this study, the physical and electrical characteristics of an AlN/4H-SiC Schottky barrier diode-based temperature sensor annealed in various gas atmospheres were investigated. An aluminum nitride (AlN) thin film was deposited on a 4H-SiC substrate via radio-frequency sputtering followed by annealing in N2 or O2 gas. The chemical composition of the film was determined by X-ray photoelectron spectroscopy (XPS) before and after annealing, and its electrical properties were evaluated by plotting a current-voltage (I-V) curve. The voltage-temperature (V-T) characteristics of the sensor were extracted from the current-voltage-temperature (I-V-T) plots constructed in the temperature range between 475 and 300 K in steps of 25 K. Sensitivities of 9.77, 9.37, and 2.16 mV/K were obtained for the as-grown, N2-annealed, and O2-annealed samples, respectively.

Effect of Sacrificial AlN (Aluminum Nitride) Layer on the Deep Surface States of 4H-SiC.

We investigated the effect of a sacrificial AlN layer on the deep energy level states of 4H-SiC surface. The samples with and without AlN layer have been annealed at 1300 °C for 30 minutes duration using a tube furnace. After annealing the samples, the changes of the carbon vacancy (VC) related Z1/2 defect characteristics were analyzed by deep level transient spectroscopy. The trap energy associated with double negative acceptor (VC(2-/0)) appears at ˜0.7 eV and was reduced from ˜0.687 to ˜0.582 eV in the sacrificial AlN layer samples. In addition, the capture cross section was significantly improved from ˜2.1×10-14 to ˜3.8×10-16 cm-2 and the trap concentration was reduced by approximately 40 times.

Comparison of Temperature Sensing Performance of 4H-SiC Schottky Barrier Diodes, Junction Barrier Schottky Diodes, and PiN Diodes.

We present a comparison between the thermal sensing behaviors of 4H-SiC Schottky barrier diodes, junction barrier Schottky diodes, and PiN diodes in a temperature range from 293 K to 573 K. The thermal sensitivity of the devices was calculated from the slope of the forward voltage versus temperature plot. At a forward current of 10 µA, the PiN diode presented the highest sensitivity peak (4.11 mV K-1), compared to the peaks of the junction barrier Schottky diode and the Schottky barrier diode (2.1 mV K-1 and 1.9 mV K-1, respectively). The minimum temperature errors of the PiN and junction barrier Schottky diodes were 0.365 K and 0.565 K, respectively, for a forward current of 80 µA±10 µA. The corresponding value for the Schottky barrier diode was 0.985 K for a forward current of 150 µA±10 µA. In contrast to Schottky diodes, the PiN diode presents a lower increase in saturation current with temperature. Therefore, the nonlinear contribution of the saturation current with respect to the forward current is negligible; this contributes to the higher sensitivity of the PiN diode, allowing for the design and fabrication of highly linear sensors that can operate in a wider temperature range than the other two diode types.

Effect of ZnO and SnO2 Nanolayers at Grain Boundaries on Thermoelectric Properties of Polycrystalline Skutterudites.

Nanostructuring is considered one of the key approaches to achieve highly efficient thermoelectric alloys by reducing thermal conductivity. In this study, we investigated the effect of oxide (ZnO and SnO2) nanolayers at the grain boundaries of polycrystalline In0.2Yb0.1Co4Sb12 skutterudites on their electrical and thermal transport properties. Skutterudite powders with oxide nanolayers were prepared by atomic layer deposition method, and the number of deposition cycles was varied to control the coating thickness. The coated powders were consolidated by spark plasma sintering. With increasing number of deposition cycle, the electrical conductivity gradually decreased, while the Seebeck coefficient changed insignificantly; this indicates that the carrier mobility decreased due to the oxide nanolayers. In contrast, the lattice thermal conductivity increased with an increase in the number of deposition cycles, demonstrating the reduction in phonon scattering by grain boundaries owing to the oxide nanolayers. Thus, we could easily control the thermoelectric properties of skutterudite materials through adjusting the oxide nanolayer by atomic layer deposition method.

Fabrication and Characterization of Oxygenated AlN/4H-SiC Heterojunction Diodes.

The effects of rapid thermal annealing (RTA) on Schottky barrier diodes (SBDs) made from oxygenated aluminum nitride (AlN) thin films deposited on a silicon carbide (SiC) substrate using radio frequency sputtering were investigated. The annealed SBD devices exhibited a 10x increase in the on/off current ratio vs. non-annealed devices for measurement temperatures ranging from 300 K to 450 K. The ideality factor, derived from the current density-voltage (J-V) characterization, increased by a factor of ~2.2 after annealing, whereas the barrier height decreased from ~0.91 to ~0.68 eV. Additionally, Auger electron spectroscopy indicated decreased concentrations of atomic oxygen in the AlN thin film, from ~36% before, to ~24% after annealing. This may have contributed to the reduced barrier height and improved on/off ratio in the annealed AlN/SiC diodes.

Enzymatic Synthesis of Formate Ester through Immobilized Lipase and Its Reuse.

Octyl formate is an important substance used in the perfume industry in products such as cosmetics, perfumes, and flavoring. Octyl formate is mostly produced by chemical catalysts. However, using enzymes as catalysts has gathered increasing interest due to their environment-friendly proprieties. In the present study, we aimed to identify the optimal conditions for the synthesis of octyl formate through immobilized enzyme-mediated esterification. We investigated the effects of enzymatic reaction parameters including the type of immobilized enzyme, enzyme concentration, molar ratio of reactants, reaction temperature, and type of solvent using the optimization method of one factor at a time (OFAT). The maximum conversion achieved was 96.51% with Novozym 435 (15 g/L), a 1:7 formic acid to octanol ratio, a reaction temperature of 40 °C, and with 1,2-dichloroethane as solvent. Moreover, we demonstrated that the Novozym 435 can be reused under the optimal conditions without affecting the octyl formate yield, which could help reduce the economic burden associated with enzymatic synthesis.

Laser digital patterning of conductive electrodes using metal oxide nanomaterials.

As an alternative approach to the conventional deposition and photolithographic processes, the laser digital patterning (LDP) process, which is also known as the laser direct writing process, has attracted considerable attention because it is a non-photolithographic, non-vacuum, on-demand, and cost-effective electrode fabrication route that can be applied to various substrates, including heat-sensitive flexible substrates. The LDP process was initially developed using noble metal nanoparticles (NPs) such as Au and Ag because such materials are free from oxidation even in a nanosize configuration. Thus, the NPs must be fused together to form continuous conductive structures upon laser irradiation. However, common metals are easily oxidized at the nanoscale and exist in oxidized forms owing to the extremely large surface-to-volume ratio of NPs. Therefore, to fabricate conductive electrodes using common metal NPs via the LDP process, laser irradiation should be used to sinter the NPs and simultaneously induce additional photochemical reactions, such as reduction, and defect structure modification to increase the conductivity of the electrodes. This review summarizes recent studies on the LDP process in which metal oxide NPs, such as ITO, ZnO, CuO, and NiO, were exclusively utilized for fabricating conductive electrodes. The outlook of the LDP process for these materials is also discussed as a method that can be used together with or as a replacement for conventional ones to produce next-generation transparent conductors, sensors, and electronics.

Maladaptive Contractility of 3D Human Cardiac Microtissues to Mechanical Nonuniformity.

Cardiac tissues are able to adjust their contractile behavior to adapt to the local mechanical environment. Nonuniformity of the native tissue mechanical properties contributes to the development of heart dysfunctions, yet the current in vitro cardiac tissue models often fail to recapitulate the mechanical nonuniformity. To address this issue, a 3D cardiac microtissue model is developed with engineered mechanical nonuniformity, enabled by 3D-printed hybrid matrices composed of fibers with different diameters. When escalating the complexity of tissue mechanical environments, cardiac microtissues start to develop maladaptive hypercontractile phenotypes, demonstrated in both contractile motion analysis and force-power analysis. This novel hybrid system could potentially facilitate the establishment of "pathologically-inspired" cardiac microtissue models for deeper understanding of heart pathology due to nonuniformity of the tissue mechanical environment.

Influence of Annealing Atmosphere on the Characteristics of Ga2O3/4H-SiC n-n Heterojunction Diodes.

Ga2O3/4H-SiC n-n isotype heterojunction diodes were fabricated by depositing Ga2O3 thin films by RF magnetron sputtering. The influence of annealing atmosphere on the film quality and electrical properties of Ga2O3 layers was investigated. X-ray diffraction (XRD) analysis showed a significant increase in the peak intensities of different faces of ß-Ga2O3 {(-201), (-401) and (002)}. X-ray photoelectron spectroscopy (XPS) measurement showed that the atomic ratio of oxygen increases under high-temperature annealing. Moreover, an N2-annealed diode exhibited a greater rectifying ratio and a lower thermal activation energy owing to the decrease in oxygen-related traps and vacancies on the Ga2O3 film and Ga2O3-metal interface.