Thermoelectric Transport in a Correlated Electron System on the Surface of Liquid Helium.

We report on the direct observation of the thermoelectric transport in a nondegenerate electron system trapped on the surface of liquid helium. The microwave-induced excitation of the vertical transitions of electrons between the surface-bound states results in their lateral flow, which we were able to detect by employing a segmented electrode configuration. We show that this flow of electrons arises due to the Seebeck effect. Our experimental results are in good agreement with the theoretical calculations based on kinetic equations. This demonstrates the importance of the fast electron-electron collisions, which, in particular, leads to the violation of the Wiedemann-Franz law in this system.

Photo-polymerization kinetics of a dental resin at a high temporal resolution.

OBJECTIVES: This study: 1) aims to measure with high temporal resolution the intrinsic rate of the degree of conversion (DC) of a dental resin-based composite (RBC) photo-cured at two irradiances; 2) aims to determine the transition time at which the DC rate is maximum; 3) used two different irradiances to measure the shift in transition time; 4) aims to compare transition times measured using DC and shrinkage strain. METHODS: Samples (n = 20) 1 mm thick by 10 mm diameter of Filtek One bulk-fill restorative A2 shade (3M Oral Care) were photocured for 20 s with a single emission peak (wavelength centered at 455 nm) light-emitting-diode-based light-curing unit at irradiance levels of 890 mW/cm2 and 209 mW/cm2, and initial sample temperature of T = 23 °C. The DC was measured in real-time using Attenuated Total Reflection (ATR) FTIR spectroscopy with a sampling rate of 13 DC data points per second. The data were analyzed within a phenomenological autocatalytic model. In addition, the axial shrinkage strain was measured using 3 samples of the RBC with the same outer dimensions and under similar experimental conditions using the bonded disk method and an interferometric technique. RESULTS: For the 890 mW/cm2 and 209 mW/cm2 irradiance levels, the DC with time was found to agree with the model enabling the determination of transition times of 0.66 ± 0.05 s and 2.3 ± 0.2 s, and the DC at these times of 5.5 ± 0.2% and 6.4 ± 0.2%. The maximum linear strain rate at 0.76 ± 0.01 s and 1.98 ± 0.02 s for the 890 mW/cm2 and 209 mW/cm2 irradiance levels, respectively, are within two standard deviations of the corresponding transition times. SIGNIFICANCE: At an irradiance level much greater than 1000 mW/cm2, the photo-polymerization kinetics of a dental RBC may be too fast to be measured accurately using ATR-FTIR spectroscopy. A viable alternative to monitor the kinetics is through the measurements of the axial shrinkage strain employing the bonded disk method and an interferometric technique.

Uniaxial-strain control of nematic superconductivity in SrxBi2Se3.

Nematic states are characterized by rotational symmetry breaking without translational ordering. Recently, nematic superconductivity, in which the superconducting gap spontaneously lifts the rotational symmetry of the lattice, has been discovered. In nematic superconductivity, multiple superconducting domains with different nematic orientations can exist, and these domains can be controlled by a conjugate external stimulus. Domain engineering is quite common in magnets but has not been achieved in superconductors. Here, we report control of the nematic superconductivity and their domains of SrxBi2Se3, through externally-applied uniaxial stress. The suppression of subdomains indicates that it is the Δ4y state that is most favoured under compression along the basal Bi-Bi bonds. This fact allows us to determine the coupling parameter between the nematicity and lattice distortion. These results provide an inevitable step towards microscopic understanding and future utilization of the unique topological nematic superconductivity.

Correlation between the beam profile from a curing light and the microhardness of four resins.

OBJECTIVE: To demonstrate the effect of localized irradiance and spectral distribution inhomogeneities of one LED-based dental light-curing unit (LCU) on the corresponding microhardness values at the top, and bottom surfaces of four dental resin-based composites (RBCs), which contained either camphorquinone (CQ) alone or a combination of CQ and monoacylphosphine oxide (TPO) as photoinitiators. METHODS: Localized irradiance beam profiles from a polywave LED-based LCU were recorded five times using a laser beam analyzer, without and with either a 400 nm or 460 nm narrow bandpass filter placed in front of the camera lens. Five specimens of each of the four RBCs (two containing CQ/TPO and two containing CQ-only) were exposed for 5-, 10-, or 30-s with the light guide directly on the top surface of the RBC. After 24 h, Knoop microhardness values were measured at 45 locations across the top and bottom surfaces of each specimen. Microhardness readings for each RBC surface and exposure time were correlated with localized patterns of the LCU beam profile, measured using the 400 nm and 460 nm bandpass filters. Spearman rank correlation was used to avoid relying on an assumption of a bivariate normal distribution for the KHN and irradiance. RESULTS: The local irradiance and spectral emission values were not uniformly distributed across the light tip. There was a strong significant positive correlation with the irradiance beam profile values from the LCU taken through bandpass filters and the microhardness maps of the RBC surfaces exposed for 5 and 10 s. The strength of this correlation decreased with increasing exposure time for the RBCs containing CQ only, and increased for the RBCs containing both CQ and TPO. CONCLUSIONS: Localized beam and spectral distributions across the tip end of the light guide strongly correlated with corresponding areas of microhardness in both the top and bottom surfaces among four RBCs with different photoinitiator contents. Significance: A light-curing unit with a highly inhomogeneous light output can adversely affect localized microhardness of resin-based composites and this may be a contributing factor for premature failure of a restoration.