Design of an Antibiotic-Releasing Polymer: Physicochemical Characterization and Drug Release Patterns.

Conventional drug delivery has its share of shortcomings, especially its rapid drug release with a relatively short duration of therapeutic drug concentrations, even in topical applications. Prolonged drug release can be effectively achieved by modifying the carrier in a drug delivery system. Among the several candidates for carriers studied over the years, poly (ether ether ketone), a biocompatible thermoplastic, was chosen as a suitable carrier. Its inherent hydrophobicity was overcome by controlled sulfonation, which introduced polar sulfonate groups onto the polymer backbone. Optimization of the sulfonation process was completed by the variation of the duration, temperature of the sulfonation, and concentration of sulfuric acid. The sulfonation was confirmed by EDS and the degree of sulfonation was determined by an NMR analysis (61.6% and 98.9%). Various physical properties such as morphology, mechanical strength, and thermal stability were studied using scanning electron microscopy, tensile testing, and thermogravimetric analysis. Cytotoxicity tests were performed on the SPEEK samples to study the variation in biocompatibility against a Vero cell line. The drug release kinetics of ciprofloxacin (CP) and nalidixic acid sodium salt (NA)-loaded membranes were studied in deionized water as well as SBF and compared against the absorbance of standardized solutions of the drug. The data were then used to determine the diffusion, distribution, and permeability coefficients. Various mathematical models were used to fit the obtained data to establish the order and mechanism of drug release. Studies revealed that drug release occurs by diffusion and follows zero-order kinetics.

Thermally Reduced Graphene Oxide as a Counter Electrode Material for Dye-Sensitized Solar Cells.

In this present study, a highly conductive thermally reduced graphene oxide (TRGO) was synthesized by a low temperature thermal reduction method using RF heating, under an argon-hydrogen atmosphere. The crystallinity and morphology were examined by X-ray diffraction, Raman spectroscopy and TEM analysis. The chemical structure including the functional groups present on TRGO was studied using X-ray photoelectron spectroscopy and FTIR analysis. The studies reveal that thermal reduction of graphene oxide was successful under the experimental conditions and that the TRGO had high crystallinity. Further, the performance of the as-prepared TRGO was tested as a counter electrode (CE) in a dye-sensitized solar cell (DSSC). The maximum power conversion efficiency (PCE) obtained was 4.86% for TRGO under one sun illumination, which is comparable to that of a platinum CE-based DSSC (5.24%). The electrocatalytic activity and electron transfer kinetics were examined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and Tafel measurements. The series resistance (Rs) and charge transfer resistance (Rct) values were found to be 35.4 Ωcm-2 and 56.40 Ωcm-2 for TRGO. The results reveal that the TRGO had an electrocatalytic performance similar to that of Pt, making TRGO-CEs promising alternatives to the conventional Pt-CEs in DSSCs.

One-Step RF-CVD Method for the Synthesis of Graphene Decorated with Metal and Metal Oxide Nanoparticles.

Bilayer and few layer-graphene (Gr) with noble metal (Ag and Au) and TiO2 nanoparticles were synthesized using atmospheric pressure radio frequency chemical vapor deposition (APRF-CVD). The precursors for the formation of the respective nanoparticles were dissolved in ethanol and injected into the APRF-CVD containing a Cu foil catalyst at 1000 °C. The graphene obtained had a blistered morphology similar to bubble-wrap. The bubble-like protrusions on the graphene sheet were caused by large nanoparticle clusters (~220 nm) formed below the graphene sheets. Smaller nanoparticles (10-80 nm) were also observed on top of the graphene sheets. Encapsulation of the nanoparticles with graphene, to yield core-shell particles was observed. Similarly, secondary growth of carbon nanotubes (CNTs) from the Au nanoparticles was observed. The average full width half maxima (FWHM) of 2D bands in the Raman spectra indicate that the graphene formed was predominantly bilayer graphene for Gr-TiO2 (55 ± 1.72 cm-1), and few-layer graphene for Gr-Ag (76 ± 22 cm-1) and Gr-Au (88 ± 4.7 cm-1). Raman spectroscopy also showed evidence for the doping of graphene and surface-enhanced Raman sensitivity (SERS) in the materials. These electronic properties of graphene with nanoparticles are relevant to various applications such as optoelectronics, catalysis, chemical and biological sensing.

In-situ preparation and characterization of acid functionalized single walled carbon nanotubes with polyimide nanofibers.

Nanofiber composites (Polyimide/f-SWCNT) of Pyromellitic dianhydride, 4,4'-Oxydianiline, and 4,4'-(4,4'-isopropylidene diphenyl-1,1'-diyl dioxy) dianiline (PMDA-ODA/IDDA) and surface-functionalized single walled carbon nanotubes (f-SWCNT) were made by electrospinning a solution of poly(amic acid) (PAA) containing 0-2 wt% f-SWCNT followed by thermal imidization. X-ray photoelectron spectroscopy spectra verified the oxidation of SWCNT surface after acid treatment, and indicated possible hydrogen bonding interactions between the f-SWCNTs and polyamic acid. High-resolution scanning electron microscopy images showed the average diameter of nanofibers to be below 150 nm, and transmission electron microscopy images showed that SWCNTs were aligned inside the polymer nanofiber. In thermogravimetric analysis, all composites showed increased thermal stability with increasing f-SWCNT content compared to neat PI. Storage modulus also increased from 124 MPa to 229 MPa from neat PI to 2% f-SWCNT composite.

Bactericidal effects of silver plus titanium dioxide-coated endotracheal tubes on Pseudomonas aeruginosa and Staphylococcus aureus.

PURPOSE: Ventilator-associated pneumonia (VAP) is a nosocomial infection resulting in significant morbidity and mortality. Pseudomonas aeruginosa (P. aeruginosa) and Staphylococcus aureus (S. aureus) are pathogens associated with VAP. Silver (Ag) coating of endotracheal tubes (ETTs) reduces bacterial colonization, however titanium dioxide (TiO(2)) coating has not been studied. METHODS: Five types of ETT coatings were applied over silica layer: Ag, solgel TiO(2), solgel TiO(2) with Ag, Degussa P25 TiO(2) (Degussa TiO(2)), and Degussa TiO(2) with Ag. After ETTs were incubated with P. aeruginosa or S. aureus; colonization was determined quantitatively. RESULTS: Pseudomonas aeruginosa and S. aureus grew for 5 days on standard ETTs. Compared to standard ETTs, P. aeruginosa growth was significantly inhibited by solgel TiO(2) with Ag at 24 hours, and by Degussa TiO(2) with Ag at 24 and 48 hours after inoculation. No significant difference in S. aureus growth was observed between the control and any of the five coatings for 5 days. CONCLUSION: In vitro, solgel TiO(2) with Ag and Degussa TiO(2) with Ag both attenuated P. aeruginosa growth, but demonstrated no effect on S. aureus colonization. Further studies using alternative coating and incorporating UV light exposure are needed to identify their potential utility in reducing VAP.