Reusable magnetic mixture of CuFe2O4-Fe2O3 and TiO2 for photocatalytic degradation of pesticides in water.

Photocatalysis is a promising treatment method to remove pollutants from water. TiO2-P25 is a commercially available model photocatalyst, which very efficiently degrades organic pollutants under UVA light exposure. However, the collection and the recovery of TiO2-P25 from cleaned water poses significant difficulties, severely limiting its usability. To address this challenge, we have prepared a sintered mixture of TiO2-P25 nanomaterials and magnetic CuFe2O4-Fe2O3 nanocomposites. The mixture material was shown to contain spinel ferrite, hematite and maghemite structures, copper predominantly in Cu2+ and iron predominantly in Fe3+ state. The CuFe2O4-Fe2O3 and TiO2-P25 mixture demonstrated magnetic collectability from processed water and photocatalytic activity, which was evidenced through the successful photodegradation of the herbicide 2,4-D. Our findings suggest that the sintered mixture of CuFe2O4-Fe2O3 and TiO2-P25 holds a promise for improving photocatalytic water treatment, with the potential to overcome current photocatalyst recovery issues.

Cobalt Phthalocyanine-Doped Polymer-Based Electrocatalyst for Rechargeable Zinc-Air Batteries.

Rechargeable zinc-air batteries (RZAB) have gained significant attention as potential energy storage devices due to their high energy density, cost-effectiveness, and to the fact that they are environmentally safe. However, the practical implementation of RZABs has been impeded by challenges such as sluggish oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), including poor cyclability. Herein, we report the preparation of cobalt- and nitrogen-doped porous carbon derived from phloroglucinol-formaldehyde polymer networks with 2-methyl imidazole and cobalt phthalocyanine as precursors for nitrogen and cobalt. The CoN-PC-2 catalyst prepared in this study exhibits commendable electrocatalytic activity for both ORR and OER, evidenced by a half-wave potential of 0.81 V and Ej=10 of 1.70 V. Moreover, the catalyst demonstrates outstanding performance in zinc-air batteries, achieving a peak power density of 158 mW cm-2 and displaying excellent stability during charge-discharge cycles. The findings from this study aim to provide valuable insights and guidelines for further research and the development of hierarchical micro-mesoporous carbon materials from polymer networks, facilitating their potential commercialisation and widespread deployment in energy storage applications.

Nanostructures Stacked on Hafnium Oxide Films Interfacing Graphene and Silicon Oxide Layers as Resistive Switching Media.

SiO2 films were grown to thicknesses below 15 nm by ozone-assisted atomic layer deposition. The graphene was a chemical vapor deposited on copper foil and transferred wet-chemically to the SiO2 films. On the top of the graphene layer, either continuous HfO2 or SiO2 films were grown by plasma-assisted atomic layer deposition or by electron beam evaporation, respectively. Micro-Raman spectroscopy confirmed the integrity of the graphene after the deposition processes of both the HfO2 and SiO2. Stacked nanostructures with graphene layers intermediating the SiO2 and either the SiO2 or HfO2 insulator layers were devised as the resistive switching media between the top Ti and bottom TiN electrodes. The behavior of the devices was studied comparatively with and without graphene interlayers. The switching processes were attained in the devices supplied with graphene interlayers, whereas in the media consisting of the SiO2-HfO2 double layers only, the switching effect was not observed. In addition, the endurance characteristics were improved after the insertion of graphene between the wide band gap dielectric layers. Pre-annealing the Si/TiN/SiO2 substrates before transferring the graphene further improved the performance.

Comparison of Toxicity and Cellular Uptake of CdSe/ZnS and Carbon Quantum Dots for Molecular Tracking Using Saccharomyces cerevisiae as a Fungal Model.

Plant resource sharing mediated by mycorrhizal fungi has been a subject of recent debate, largely owing to the limitations of previously used isotopic tracking methods. Although CdSe/ZnS quantum dots (QDs) have been successfully used for in situ tracking of essential nutrients in plant-fungal systems, the Cd-containing QDs, due to the intrinsic toxic nature of Cd, are not a viable system for larger-scale in situ studies. We synthesized amino acid-based carbon quantum dots (CQDs; average hydrodynamic size 6 ± 3 nm, zeta potential -19 ± 12 mV) and compared their toxicity and uptake with commercial CdSe/ZnS QDs that we conjugated with the amino acid cysteine (Cys) (average hydrodynamic size 308 ± 150 nm, zeta potential -65 ± 4 mV) using yeast Saccharomyces cerevisiae as a proxy for mycorrhizal fungi. We showed that the CQDs readily entered yeast cells and were non-toxic up to 100 mg/L. While the Cys-conjugated CdSe/ZnS QDs were also not toxic to yeast cells up to 100 mg/L, they were not taken up into the cells but remained on the cell surfaces. These findings suggest that CQDs may be a suitable tool for molecular tracking in fungi (incl. mychorrhizal fungi) due to their ability to enter fungal cells.

Memory Effects in Nanolaminates of Hafnium and Iron Oxide Films Structured by Atomic Layer Deposition.

HfO2 and Fe2O3 thin films and laminated stacks were grown by atomic layer deposition at 350 °C from hafnium tetrachloride, ferrocene, and ozone. Nonlinear, saturating, and hysteretic magnetization was recorded in the films. Magnetization was expectedly dominated by increasing the content of Fe2O3. However, coercive force could also be enhanced by the choice of appropriate ratios of HfO2 and Fe2O3 in nanolaminated structures. Saturation magnetization was observed in the measurement temperature range of 5-350 K, decreasing towards higher temperatures and increasing with the films' thicknesses and crystal growth. Coercive force tended to increase with a decrease in the thickness of crystallized layers. The films containing insulating HfO2 layers grown alternately with magnetic Fe2O3 exhibited abilities to both switch resistively and magnetize at room temperature. Resistive switching was unipolar in all the oxides mounted between Ti and TiN electrodes.

Bifunctional Oxygen Electrocatalysis on Mixed Metal Phthalocyanine-Modified Carbon Nanotubes Prepared via Pyrolysis.

Non-precious-metal catalysts are promising alternatives for Pt-based cathode materials in low-temperature fuel cells, which is of great environmental importance. Here, we have investigated the bifunctional electrocatalytic activity toward the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) of mixed metal (FeNi; FeMn; FeCo) phthalocyanine-modified multiwalled carbon nanotubes (MWCNTs) prepared by a simple pyrolysis method. Among the bimetallic catalysts containing nitrogen derived from corresponding metal phthalocyanines, we report the excellent ORR activity of FeCoN-MWCNT and FeMnN-MWCNT catalysts with the ORR onset potential of 0.93 V and FeNiN-MWCNT catalyst for the OER having EOER = 1.58 V at 10 mA cm-2. The surface morphology, structure, and elemental composition of the prepared catalysts were examined with scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The FeCoN-MWCNT and FeMnN-MWCNT catalysts were prepared as cathodes and tested in anion-exchange membrane fuel cells (AEMFCs). Both catalysts displayed remarkable AEMFC performance with a peak power density as high as 692 mW cm-2 for FeCoN-MWCNT.

Transition-Metal- and Nitrogen-Doped Carbide-Derived Carbon/Carbon Nanotube Composites as Cathode Catalysts for Anion-Exchange Membrane Fuel Cells.

Transition-metal- and nitrogen-codoped carbide-derived carbon/carbon nanotube composites (M-N-CDC/CNT) have been prepared, characterized, and used as cathode catalysts in anion-exchange membrane fuel cells (AEMFCs). As transition metals, cobalt, iron, and a combination of both have been investigated. Metal and nitrogen are doped through a simple high-temperature pyrolysis technique with 1,10-phenanthroline as the N precursor. The physicochemical characterization shows the success of metal and nitrogen doping as well as very similar morphologies and textural properties of all three composite materials. The initial assessment of the oxygen reduction reaction (ORR) activity, employing the rotating ring-disk electrode method, indicates that the M-N-CDC/CNT catalysts exhibit a very good electrocatalytic performance in alkaline media. We find that the formation of HO2 - species in the ORR catalysts depends on the specific metal composition (Co, Fe, or CoFe). All three materials show excellent stability with a negligible decline in their performance after 10000 consecutive potential cycles. The very good performance of the M-N-CDC/CNT catalyst materials is attributed to the presence of M-N x and pyridinic-N moieties as well as both micro- and mesoporous structures. Finally, the catalysts exhibit excellent performance in in situ tests in H2/O2 AEMFCs, with the CoFe-N-CDC/CNT reaching a current density close to 500 mA cm-2 at 0.75 V and a peak power density (P max) exceeding 1 W cm-2. Additional tests show that P max reaches 0.8 W cm-2 in an H2/CO2-free air system and that the CoFe-N-CDC/CNT material exhibits good stability under both AEMFC operating conditions.

Nanoindentation of Chromium Oxide Possessing Superior Hardness among Atomic-Layer-Deposited Oxides.

Chromium (III) oxide is a technologically interesting material with attractive chemical, catalytic, magnetic and mechanical properties. It can be produced by different chemical and physical methods, for instance, by metal-organic chemical vapor deposition, thermal decomposition of chromium nitrate Cr(NO3)3 or ammonium dichromate (NH4)2Cr2O7, magnetron sputtering and atomic layer deposition. The latter method was used in the current work to deposit Cr2O3 thin films with thicknesses from 28 to 400 nm at deposition temperatures from 330 to 465 °C. The phase composition, crystallite size, hardness and modulus of elasticity were measured. The deposited Cr2O3 thin films had different structures from X-ray amorphous to crystalline α-Cr2O3 (eskolaite) structures. The averaged hardness of the films on SiO2 glass substrate varied from 12 to 22 GPa and the moduli were in the range of 76-180 GPa, as determined by nanoindentation. Lower values included some influence from a softer deposition substrate. The results indicate that Cr2O3 could be a promising material as a mechanically protective thin film applicable, for instance, in micro-electromechanical devices.

Atomic layer deposition of superparamagnetic ruthenium-doped iron oxide thin film.

Due to the several applications of biosensors, such as magnetic hyperthermia and magnetic resonance imaging, the use of superparamagnetic nanoparticles or thin films for preparing biosensors has increased greatly. We report herein on a strategy to fabricate a nanostructure composed of superparamagnetic thin films. Ruthenium-doped iron oxide thin films were deposited by using atomic layer deposition at 270 and 360 °C. FeCl3 and Ru(EtCp)2 were used as metal precursors and H2O/O2 as the oxygen precursor. Doping with ruthenium helps to lower the formation temperature of hematite (α-Fe2O3). Ruthenium content was changed from 0.42 at% up to 29.7 at%. Ru-doped films had a nano-crystallized structure of hematite with nanocrystal sizes from 4.4 up to 7.8 nm. Magnetization at room temperature was studied in iron oxide and Ru-doped iron oxide films. A new finding is a demonstration that in a Ru-doped iron oxide thin film superparamagnetic behavior of nanocrystalline materials (α-Fe2O3) is observed with the maximum magnetic coercive force H c of 3 kOe. Increasing Ru content increased crystallite size of hematite and resulted in a lower blocking temperature.

Magnetic and Electrical Performance of Atomic Layer Deposited Iron Erbium Oxide Thin Films.

Mixed films of a high-permittivity oxide, Er2O3, and a magnetic material, Fe2O3, were grown by atomic layer deposition on silicon and titanium nitride at 375 °C using erbium diketonate, ferrocene, and ozone as precursors. Crystalline phases of erbium and iron oxides were formed. Growth into three-dimensional trenched structures was demonstrated. A structure deposited using tens to hundreds subsequent cycles for both constituent metal oxide layers promoted both charge polarization and saturative magnetization compared to those in the more homogeneously mixed films.

Functionalization of Titanium Alloy Surface by Graphene Nanoplatelets and Metal Oxides: Corrosion Inhibition.

Corrosion inhibition of metallic substrates is an important and crucial step for great economical as well as environmental savings. In this paper, we introduce an extra thin effective corrosion inhibitive material having layered structure designed for protection and functionalization of Ti Grade 5 alloy substrates. The coating consists of a first layer made of thin graphene nanoplatelets, on top of which a multilayer Al2O3 and TiO2 films is applied by low-temperature atomic layer deposition. The amorphous structure of the metal oxide films was confirmed by micro-Raman and X-ray diffraction analysis. Corrosion inhibition ability of the prepared coatings was analyzed by open circuit potential, potentiodynamic plot and by voltammetric analysis, in aqueous potassium bromide solution. The open circuit potential of the graphene-metal oxide coated substrate showed much passive nature than bare substrate or graphene coated or only metal oxide coated substrates. The localized corrosion potential of the graphene-metal oxide coated, only metal oxide coated, and bare substrates were found 5.5, 3.0, and 1.1 V, respectively. In addition, corrosion current density values of the graphene-metal oxide and only metal oxide coated substrates showed much more passive nature than the bare and graphene coated substrates. Long immersion test in the salt solution further clarified the effective corrosion inhibition of the graphene-metal oxide coated substrate. The analyzed results reflect that the graphene-metal oxide films can be used to prepare better and effective corrosion inhibition coatings for the Ti Grade 5 alloy to increase their lifetime.

Graphene Nanoplatelets Based Protective and Functionalizing Coating for Stainless Steel.

Stainless steel is the most widely used alloy for many industrial and everyday applications, and protection of this alloy substrate against corrosion is an important industrial issue. Here we report a promising application of graphene oxide and graphene nanoplatelets as effective corrosion inhibitors for AISI type 304 stainless steel alloy. The graphene oxide and graphene coatings on the stainless steel substrates were prepared using spin coating techniques. Homogeneous and complete surface coverage by the graphene oxide and graphene nanoplatelets were observed with a high-resolution scanning electron microscope. The corrosion inhibition ability of these materials was investigated through measurement of open circuit potential and followed by potentiodymamic polarization analysis in aqueous sodium chloride solution before and after a month of immersion. Analyzed result exhibits effective corrosion inhibition for both substrates coated with graphene oxide or graphene nanoplatelets by increasing corrosion potential, pitting potential and decreasing passive current density. The corrosion inhibition ability of the coated substrates has not changed even after the long-term immersion. The result showed both graphene materials can be used as an effective corrosion inhibitor for the stainless steel substrates, which would certainly increase lifetime the substrate. However, long-term protection ability of the graphene coated susbtsrate showed somewhat better inhibition performance than the ones coated with graphene oxide.

Electrospun nanofibers as a potential controlled-release solid dispersion system for poorly water-soluble drugs.

Electrospinning was introduced as a novel technique for preparing controlled-release (CR) amorphous solid dispersions (SD) and polymeric nanofibers of a poorly water-soluble drug. Piroxicam (PRX) was used as a low-dose poorly-soluble drug and hydroxypropyl methylcellulose (HPMC) as an amorphous-state stabilising carrier polymer in nanofibers. Raman spectroscopy, X-ray powder diffraction (XPRD), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were used in the physical characterisation of the CR-SD nanofibers. Special attention was paid on the effects of a polymer and solvent system on the solid-state properties and physical stability of nanofibers. The average dry diameter of the electrospun CR-SD nanofibers ranged from 400 to 600 nm (SEM). PRX existed in amorphous form in the nanofibers immediately after fabrication and after a short-term (3-month) aging at low temperature (6-8 °C/0% RH) and ambient room temperature (22 °C/0% RH). At higher temperature and humidity (30 °C/85% RH), however, amorphous PRX in the nanofibers tended to slowly recrystallise to PRX form III. The electrospun CR-SD nanofibers exhibited a short lag-time, the absence of initial burst release and zero-order linear CR dissolution kinetics. In conclusion, electrospinning can be used to fabricate supersaturating CR-SD nanofibers of PRX and HPMC, and to stabilise the amorphous state of PRX.

Nanometer depth resolution in 3D topographic analysis of drug-loaded nanofibrous mats without sample preparation.

We showed that scanning white light interferometry (SWLI) can provide nanometer depth resolution in 3D topographic analysis of electrospun drug-loaded nanofibrous mats without sample preparation. The method permits rapidly investigating geometric properties (e.g. fiber diameter, orientation and morphology) and surface topography of drug-loaded nanofibers and nanomats. Electrospun nanofibers of a model drug, piroxicam (PRX), and hydroxypropyl methylcellulose (HPMC) were imaged. Scanning electron microscopy (SEM) served as a reference method. SWLI 3D images featuring 29 nm by 29 nm active pixel size were obtained of a 55 µm × 40 µm area. The thickness of the drug-loaded non-woven nanomats was uniform, ranging from 2.0 µm to 3.0 µm (SWLI), and independent of the ratio between HPMC and PRX. The average diameters (n=100, SEM) for drug-loaded nanofibers were 387 ± 125 nm (HPMC and PRX 1:1), 407 ± 144 nm (HPMC and PRX 1:2), and 290 ± 100 nm (HPMC and PRX 1:4). We found advantages and limitations in both techniques. SWLI permits rapid non-contacting and non-destructive characterization of layer orientation, layer thickness, porosity, and surface morphology of electrospun drug-loaded nanofibers and nanomats. Such analysis is important because the surface topography affects the performance of nanomats in pharmaceutical and biomedical applications.

Water-mediated solid-state transformation of a polymorphic drug during aqueous-based drug-layer coating of pellets.

During aqueous drug-layer coating, drug substance(s) are exposed to water and elevated temperatures which can lead to water-mediated process induced transformations (PITs). The effects of aqueous drug-layer coating of pellets (Cellets(®)) on the anhydrous piroxicam, PRX, were investigated in the miniaturized coating equipment and with free films. Hydroxypropyl methylcellulose (HPMC) was used as a carrier coating polymer. Free films were prepared by using an in-house small-scale rotating plate system equipped with an atomization air nozzle. Raman spectroscopy, X-ray powder diffraction (XRPD), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM) were used to characterize the solid-state properties and surface morphology of the pellets and free films. The results showed that anhydrous PRX form I (AH) and monohydrate (MH) were stable during drug-layer coating, but amorphous PRX in solid dispersion (SD) crystallized as MH already after 10 min of coating. Furthermore, the increase in a dissolution rate was achieved from the drug-layer coated inert pellets compared to powder forms. In conclusion, water-mediated solid-state PITs of amorphous PRX is evident during aqueous-based drug-layer coating of pellets, and solid-state change can be verified using Raman spectroscopy.