ABSTRACT
In this study, caffeine-loaded photoresin composites with homogeneous structures, suitable for additive manufacturing of transdermal microneedle systems, were obtained. The properties of the composites with varying caffeine concentrations (0.1-0.4% w/w) were investigated for carbon-carbon double bond conversion using Fourier Transform Infrared Spectroscopy, surface wettability and mechanical properties using a static tensile test and nanoindentation, and caffeine release in ethanol using UV-Vis. The caffeine concentration did not affect the final degree of double bond conversion, which was confirmed in tensile tests, where the strength and Young's modulus of caffeine-loaded samples had comparable values to control ones. Samples with 0.1 and 0.2% caffeine content showed an increase in nanohardness and reduced elastic modulus of 50 MPa and 1.5 MPa, respectively. The good wettability of the samples with water and the increase in surface energy is a favorable aspect for the dedicated application of the obtained composite materials. The amount of caffeine released into the ethanol solution at 1, 3 and 7 days reached a maximum value of 81%, was higher for the lower concentration of caffeine in the sample and increased over time. The conducted research may enhance the potential application of composite materials obtained through the digital light processing method in additive manufacturing.
ABSTRACT
INTRODUCTION: 3D printing (3DP) applications in medicine are intensively investigated, creating an opportunity to provide patient-tailored therapy by delivering a drug with an accurate dose and release profile. Moving away from the 'one size fits all' paradigm, it could be beneficial for treating mental and neurological disorders, improving the efficiency and safety of the therapy. The aim of this critical review is to assess recent advances and identify gaps regarding 3DP in this important and challenging field, by focusing on recent research examples. AREAS COVERED: Applications of the 3DP techniques for solid dosage forms in mental and neurological disorders have been covered and discussed, together with recent advantages, limitations, and future directions. EXPERT OPINION: The personalize treatment, which is considered as the most significant advantage of the 3DP technique, can be beneficial in mental and neurological disorders therapy, where the dose should be adjusted to the patient. Printing of medicines enables creating the structure modifications and thus controlling the drug release or combining multiple drugs into one tablet, simplifying the dose regimen. Medications printed on-demand, in health-care facilities, could address the special needs of pediatric patients and help avoid interruptions in the supply chain. Despite promising advances, the described methods have limitations and need further investigation before being scaled-up to an industrial manufacturing environment. There is also a need to establish protocols for the preparation and registration of 3DP dosage forms.
ABSTRACT
The article presents the results of research on the influence of the natural moisture of a filament made of acrylonitrile-butadiene-styrene terpolymer (ABS) on the mechanical properties and quality of products fabricated with fused filament fabrication (FFF). The concept of the natural moisture of the filament was defined, and the range of its variability was identified in reference to the range of the natural ambient humidity. It is shown that a change in the ambient humidity by 10% resulted in a change in filament moisture by about 0.05%. The results of the research on the moisture variability of an ABS filament stored in a package, an airtight container, or a container with a moisture absorber are also discussed. The last part of the article presents the results of the research on the impact of the moisture of the filament in its natural range of variability on select mechanical properties of filaments and products made using FFT. It is shown that this impact was significant and had a value of 1 MPa on 0.1% filament moisture.
ABSTRACT
Growing age and different conditions often require the replacement of orthoses, and FDM-based 3D printing can produce them quickly with less investment. In today's market for orthotics, these characteristics are highly desired. Therefore, this study is fully focused on the optimization and strength analysis of FDM 3D-printed ankle-foot orthoses (AFO) fabricated using PLA and PLA reinforced with carbon fiber (PLA-C). An increase in ankle plantar-flexor force can be achieved by reinforcing thermoplastic AFOs with CFs. Specially designed mechanical strength tests were conducted at the UTM to generate force-displacement curves for stored elastic energy and fracture studies. The mechanical behavior of both AFOs was predicted with the help of an FEA. The model predictions were validated by comparing them with mechanical strength testing conducted under the same loading and boundary conditions as the FEA. In both the prediction and experimental analysis, the PLA-C-based AFOs were stiffer and could withstand greater loads than the PLA-based AFOs. An area of high stress in the simulation and a fracture point in experimentation were both found at the same location. Furthermore, these highly accurate models will allow the fabrication of AFOs to be improved without investing time and resources on trials.
ABSTRACT
This paper presents the results of experiments conducted on a batch of additively manufactured customized prosthetic sockets for upper limbs, made of thermoplastics and designed automatically on the basis of a 3D-scanned limb of a 3-year-old patient. The aim of this work was to compare sockets made of two different materials-rigid PLA and elastic TPE. Two distinct socket designs with various mounting systems were prepared. To find a reliable set of parameters for cheap and stable manufacturing of usable prostheses using 3D printers, realizing the fused deposition modeling (FDM) process, sets of sockets were manufactured with various process parameters. This paper presents the methodology of the design, the plan of the experiments and the obtained results in terms of process stability, fit and assessment by patient, as well as strength of the obtained sockets and their measured surface roughness. The results are promising, as most of the obtained products fulfil the strength criteria, although not all of them meet the fitting and use comfort criteria. As a result, recommendations of materials and process parameters were determined. These parameters were included in a prototype of the automated design and production system developed by the authors, and prostheses for several other patients were manufactured.
ABSTRACT
The paper presents results of research conducted on a batch of additively manufactured individualized openwork wrist-hand orthoses made of thermoplastics and designed automatically based on 3D-scanned geometry of a given patient. The aim of the work was to establish an automated design process and find a reliable set of parameters for rapid and affordable manufacturing of usable orthoses on popular 3D printers, with little or no supervision of the process. The paper presents motivations, methodology of automated design, plan of manufacturing and testing, the obtained results in terms of process stability, fit and assessment by patient and strength of the obtained orthoses. Almost 100 manufacturing processes of ready-to-use orthosis parts were carried out in a controlled environment and their results were analyzed thoroughly. The results are promising, as most of the obtained products fulfil the strength criteria, although not all of them meet the economic criteria. As a result, a recommended set of process parameters was determined. These parameters were included in a prototype of the automated design and in a production system developed by the authors.
