ABSTRACT
OBJECTIVE: The aim of this work was to study the granule growth kinetics during in situ fluid bed melt granulation process using real-time particle size measurement techniques. In addition, the usefulness of these techniques during scale-up of melt granulation was evaluated. MATERIALS AND METHODS: Focused beam reflectance measurement (FBRM) and spatial filtering technique (SFT) probes were used within the process chamber of fluid bed granulator for real-time in-line granule size analysis. RESULTS: The results demonstrated that the use of in-line particle size probes in fluid bed granulator during the process offers an insightful view of granule growth and allows in-process monitoring of granule chord length changes. The effect of selected critical parameters (binder content, inlet air temperature and product endpoint temperature) on the granule growth was clearly presented by in-line measurements in a laboratory scale. A comparison of granule size measurements from both FBRM and SFT probes showed similar particle growth trends, which were in close correlation to the product temperature. Comparable trends in end granule particle size were observed when comparing different in-line, at-line and off-line particle size measurements. CONCLUSION: The in-line FBRM and SFT probes were successfully employed in in situ fluid bed melt granulation process to study the influence of critical formulation/process parameters on the granule growth kinetics. The scale-up experiment confirmed the potential of these in-line granule size measurement techniques as a viable tool for process monitoring during the transfer of granulation to the larger scale or another manufacturing site/equipment.
Subject(s)
Carbazoles/chemistry , Cellulose/chemistry , Drug Compounding/methods , Excipients/chemistry , Propanolamines/chemistry , Calorimetry, Differential Scanning , Carvedilol , Chemistry, Pharmaceutical , Drug Compounding/instrumentation , Kinetics , Microscopy, Electron, Scanning , Particle Size , Powders , Surface PropertiesABSTRACT
The purpose of this study was to prepare and characterize granulated carvedilol by melt-in and spray-on melt granulation in a fluid bed and a high shear granulator. Granulates having comparable particle size distribution and good flow properties were obtained with proper adjustment of process parameters for each binder (poloxamer 188, polyethylene glycol 4000, and gliceryl monosterate), procedure (spray-on and melt-in) and equipment (fluid bed and high shear granulator). In-line probes for particle size measurements proved to be a useful tool for determining the end point of melt granulation. The product temperature during melt granulation was found to be the critical process parameter for achieving appropriate granulate particle size distribution. The results showed that melt granulation using hydrophilic binders is an effective method to improve the dissolution rate of carvedilol. The method of binder addition to the powders (melt-in or spray-on procedure) was found to strongly influence the dissolution rate of carvedilol. The highest dissolution rates were obtained when the spray-on procedure is used, independently from the type of granulator used. The results also suggest that the most probable explanation for the increase in the dissolution rate of granulated carvedilol is improvement of the wettability through intimate contact between hydrophilic binder and hydrophobic drug.
Subject(s)
Adrenergic Antagonists/chemistry , Carbazoles/chemistry , Hot Temperature , Propanolamines/chemistry , Technology, Pharmaceutical/methods , Transition Temperature , Carvedilol , Chemistry, Pharmaceutical , Drug Stability , Excipients/chemistry , Glycerides/chemistry , Hydrophobic and Hydrophilic Interactions , Kinetics , Particle Size , Poloxamer/chemistry , Polyethylene Glycols/chemistry , Rheology , Solubility , Spectrum Analysis, Raman , ViscosityABSTRACT
The objective of this work was to investigate the influence of selected individual variables (binder content, inlet air temperature, and product endpoint temperature) of in situ fluid bed melt granulation on the granule particle size distribution and percentage of dissolved carvedilol using a three-factor, five-level circumscribed central composite design. Increased binder content had the effect of increasing the granule particle size and drug dissolution rate. The effect of inlet air temperature and product endpoint temperature was found to be more pronounced in case of granule particle size parameters. Within the studied intervals, the optimal quantity of binder as well as optimal process parameters were identified and validated using response surface methodology. Utilizing these optimal process and formulation parameters, successful scaling up of the fluid bed melt granulation process was carried out. Granule characteristics obtained at pilot scale are comparable to those obtained at laboratory scale.
