Revolutionizing Leishmaniasis Treatment with Cutting Edge Drug Delivery Systems and Nanovaccines: An Updated Review.

Leishmaniasis, one of the most overlooked tropical diseases, is a life-threatening illness caused by the parasite Leishmania donovani that is prevalent in underdeveloped nations. Over 350 million individuals in more than 90 different nations worldwide are at risk of contracting the disease, which has a current fatality rate of 50 000 mortalities each year. The administration of liposomal Amp B, pentavalent antimonials, and miltefosine are still considered integral components of the chemotherapy regimen. Antileishmanial medications fail to treat leishmaniasis because of their numerous drawbacks. These include inadequate effectiveness, toxicity, undesired side effects, drug resistance, treatment duration, and cost. Consequently, there is a need to overcome the limitations of conventional therapeutics. Nanotechnology has demonstrated promising outcomes in addressing these issues because of its small size and distinctive characteristics, such as enhanced bioavailability, lower toxicity, biodegradability, and targeted drug delivery. This review is an effort to highlight the recent progress in various nanodrug delivery systems (nDDSs) over the past five years for treating leishmaniasis. Although the preclinical outcomes of nDDSs have shown promising treatment for leishmaniasis, further research is needed for their clinical translation. Advancement in three primary priority domains─molecular diagnostics, clinical investigation, and knowledge dissemination and standardization─is imperative to propel the leishmaniasis field toward translational outcomes.

Biofilm Inhibition on Medical Devices and Implants Using Carbon Dots: An Updated Review.

Biofilms are an intricate community of microbes that colonize solid surfaces, communicating via a quorum-sensing mechanism. These microbial aggregates secrete exopolysaccharides facilitating adhesion and conferring resistance to drugs and antimicrobial agents. The escalating global concern over biofilm-related infections on medical devices underscores the severe threat to human health. Carbon dots (CDs) have emerged as a promising substrate to combat microbes and disrupt biofilm matrices. Their numerous advantages such as facile surface functionalization and specific antimicrobial properties, position them as innovative anti-biofilm agents. Due to their minuscule size, CDs can penetrate microbial cells, inhibiting growth via cytoplasmic leakage, reactive oxygen species (ROS) generation, and genetic material fragmentation. Research has demonstrated the efficacy of CDs in inhibiting biofilms formed by key pathogenic bacteria such as Escherichia coli, Staphylococcus aureus, and Pseudomonas aeruginosa. Consequently, the development of CD-based coatings and hydrogels holds promise for eradicating biofilm formation, thereby enhancing treatment efficacy, reducing clinical expenses, and minimizing the need for implant revision surgeries. This review provides insights into the mechanisms of biofilm formation on implants, surveys major biofilm-forming pathogens and associated infections, and specifically highlights the anti-biofilm properties of CDs emphasizing their potential as coatings on medical implants.

Joining of Dissimilar Al and Mg Metal Alloys by Friction Stir Welding.

In engineering applications, such as automobile, marine, aerospace, and railway, lightweight alloys of aluminum (Al) and magnesium (Mg) ensure design fitness for fuel economy, better efficiency, and overall cost reduction. Friction stir welding (FSW) for joining dissimilar materials has been considered better than the conventional fusion welding process because of metallurgical concerns. In this study, dissimilar joints were made between the AA6061 (A), AZ31B (B), and AZ91D (C) combinations based on the varying advancing side (AS) and retreating side (RS). The dissimilar joints prepared by the FSW process were further characterized by tensile testing, impact testing, corrosion testing, fracture, and statistical and cost analysis. The results revealed a maximum tensile strength of 192.39 MPa in AZ91 and AZ31B, maximum yield strength of 134.38 MPa in a combination of AA6061 and AZ91, maximum hardness of 114 Hv in AA6061 and AZ31B, and lowest corrosion rate of 7.03 mV/A in AA6061 and AZ31B. The results of the properties were supported by photomicrographic fracture analysis by scanning electron microscopy (SEM) observations. Further, the performance of dissimilar joints was statistically analyzed and prioritized for preference by similarity to the ideal solution (TOPSIS) method.

On 3D printed biomedical sensors for non-enzymatic glucose sensing applications.

Some studies have been reported in the recent past on smart sensors for non-enzymatic glucose sensing applications. Nevertheless, little has been reported on the in-house development of low-cost 3D printed smart biomedical sensors with tunable sensitivity. This study reports investigations on the in-house, low-cost fabrication of polyvinyl difluoride (PVDF) matrix-based 3D printed tunable non-enzymatic glucose sensors. For fabrication of smart sensors, Cu (4%) doped ZnO nanoparticles have been reinforced (in different weight proportions (wt%) in PVDF matrix through melt processing. The results suggest that 4% reinforcement (of 4% Cu doped-ZnO), processed at 190°C, 40 rpm screw speed on twin screw extrusion (TSE) followed by post heat treatment (HT) at 60°C are the best settings for fabrication of feedstock filaments (for bio-sensor 3D printing). Finally, a PVDF-based sensor to support bioreceptor and transducer requirements has been successfully prepared (with 4D properties (i.e. one-way programing feature), optical, morphological, bond strength, piezoelectric and mechanical characteristics). The 3D printed electro-active sensor, (of selected composition) resulted in acceptable mechanical, piezoelectric, and dielectric properties (modulus of toughness (MoT) 1.46 MPa, Young's modulus (YM) 1221.7 MPa, piezoelectric coefficient 19.3pC/N and dielectric constant 6.5). The results have been supported by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), current-voltage-resistance (I-V-R), and Fourier transformed infrared (FTIR) analysis.

Thermomechanical investigations of PEKK-HAp-CS composites.

In this experimental study, a composite of poly-ether-ketone-ketone by reinforcement of hydroxyapatite and chitosan has been prepared for possible applications as orthopaedic scaffolds. Initially, different weight percentages of hydroxyapatite and chitosan were reinforced in the poly-ether-ketone-ketone matrix and tested for melt flow index in order to check the flowability of different compositions/proportions. Suitable compositions revealed by the melt flow index test were then taken forward for the extrusion of filament required for fused deposition modelling. For thermomechanical investigations, Taguchi-based design of experiments has been used with input variables in the extrusion process as follows: temperature, load applied and different composition/proportions. The specimens in the form of feedstock filament produced by the extrusion process were made to undergo tensile testing. The specimens were also inspected by differential scanning calorimetry and photomicrographs. Finally, the specimen showing the best performance from the thermomechanical viewpoint has been selected to extrude the filament for the fused deposition modelling process.

Multi-Material Additive Manufacturing of Sustainable Innovative Materials and Structures.

This paper highlights the multi-material additive manufacturing (AM) route for manufacturing of innovative materials and structures. Three different recycled thermoplastics, namely acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), and high impact polystyrene (HIPS) (with different Young's modulus, glass transition temperature, rheological properties), have been selected (as a case study) for multi-material AM. The functional prototypes have been printed on fused deposition modelling (FDM) setup as tensile specimens (as per ASTM D638 type-IV standard) with different combinations of top, middle, and bottom layers (of ABS/PLA/HIPS), at different printing speed and infill percentage density. The specimens were subjected to thermal (glass transition temperature and heat capacity) and mechanical testing (peak load, peak strength, peak elongation, percentage elongation at peak, and Young's modulus) to ascertain their suitability in load-bearing structures, and the fabrication of functional prototypes of mechanical meta-materials. The results have been supported by photomicrographs to observe the microstructure of the analyzed multi-materials.