Accuracy of torque controllers on healing abutments in implant dentistry-an in vitro study.

PURPOSE: To evaluate the accuracy of three torque-control devices used on healing abutments in implant prosthodontics. MATERIALS AND METHODS: In this in vitro experiment, three torque controllers, Ankylos friction-based, Straumann spring-based, and Anthogyr pre-calibrated torque control devices were used to tighten the healing abutments of Ankylos and Straumann dental implants to a pre-determined value of 15 Ncm. A digital torque meter (DT), Cedar DID-4A, was used to assess removal torque as a surrogate for the accuracy of the torque controllers to apply a tightening force of 15 Ncm on healing abutments.  One-way analysis of variance (ANOVA) was used to identify differences between each torque controller and the digital torquemeter, a p < 0.05 was considered significant. RESULTS: The torque required to remove the healing abutments was 16.05 ± 0.66 Ncm for the Ankylos ratchet, 12.61 ± 0.90 Ncm for the Straumann ratchet, and 14.37 ± 1.08 Ncm for the Anthogyr torque-control device. Significant statistical differences were observed between Ankylos and the control digital torquemeter (p = 1.84E-8 ; F = 50.3); Anthogyr and control digital torquemeter (p = 0.01; F = 6.79); and Straumann and control digital torquemeter (p = 0.01; F = 141.15). CONCLUSION: Friction-based (Ankylos), spring-based (Straumann), and pre-calibrated (Anthogyr) torque control devices present over-torque and under-torque values when used over healing abutments of Ankylos and Straumann implant systems.

Implant and prosthetic rehabilitation of a patient with mucous membrane pemphigoid.

Mucous membrane pemphigoid (MMP) is an autoimmune condition characterized by subepithelial separation and deposition of autoantibodies and complement along the basement membrane zone. The disease results in the development of vesiculobullous lesions of the mucous membranes and skin. This report discusses the surgical treatment and management and the prosthetic implant rehabilitation of a patient with mucous membrane pemphigoid. The rationale for this treatment was to fabricate a prosthesis that was stable and did not rub against the gingival tissues and that was easily cleaned. The overdenture attachment system used provides more stability than other attachment systems while allowing the prosthesis and abutments to be easily cleaned.

Dentist-laboratory communication and quality assessment of removable prostheses in Oregon: A cross-sectional pilot study.

STATEMENT OF PROBLEM: When fabricating a removable dental prosthesis, it is unclear if the information received by the dental laboratory technician is clear and sufficient. PURPOSE: The purpose of this survey study was to evaluate the dentist's work authorizations for removable prostheses as well as determine common practices used by laboratories during the fabrication of removable prostheses. MATERIAL AND METHODS: A 24-item questionnaire was developed based on previously published questionnaires and incorporating new topics. A public uniform resource locator (URL) survey link was generated and sent to the office of the Oregon Association of Dental Laboratories (OADL). The executive director of the board then sent out the link to 163 participants that included members and nonmembers of the OADL who were still active in the state of Oregon. Two reminder e-mails were sent 2 weeks apart. Study data were collected and managed by using the Research Electronic Data Capture (REDCap) software program. Descriptive statistics were tabulated, and responses displayed as a percentage of the total. RESULTS: From the 163 invited participants, 26 responded to the survey representing a 15.9% response rate. Only 11% of the laboratories stated that they routinely receive work authorizations with clear instructions. All participants stated that they always (62.5%) or frequently (37.5%) design the partial prostheses frameworks. Only 37.5% of the laboratories stated that they usually receive adequately extended and accurate definitive casts to fabricate the framework. Fifty percent of the laboratories stated that they very rarely perform altered cast procedures and 50% indicated that half or more of the removable partial prostheses they fabricate were entirely made of acrylic resin. Most laboratories stated that thermoplastic resin partial dentures were less than 25% of their produced volume of removable prostheses. Only 22% of respondents stated that they usually receive adequate information to complete a denture tooth arrangement and most (78%) dentists do not routinely specify the type of occlusal scheme desired for their complete denture tooth arrangements. In most prostheses (77%), posterior palatal seal was marked by the prescribing dentists rarely or very rarely. CONCLUSIONS: Work authorizations provided by the dentists were less than adequate and left much decision-making to the dental laboratory technician.

Shark Fin Titanium Hollow Bulb Obturator: A Treatment Concept.

Restoring esthetics and function for patients with maxillectomy defects presents a complex challenge for the clinician. Obturator prostheses are subject to rotational forces during function, allowing movement into the defect. Gaining prosthesis support from endosseous implants can limit the amount of rotation. Xerostomia and impaired tissue healing caused by radiation therapy further complicates the treatment for such patients. Several resilient and rigid obturator design concepts are available for restoration of such defects. This clinical report describes a design concept used to treat a patient with a maxillectomy defect caused by tumor resection secondary to a squamous cell carcinoma.

Digital Relief of the Mental Foramen for a CAD/CAM-Fabricated Mandibular Denture.

Relief of the intaglio surface of a denture base is conventionally performed using thin wax and soft metal foil attached to the master cast. The following report highlights a new relief procedure for the mental foramen using a CT double scan technique on the CAD/CAM dentures fabricated for the patient with paresthesia of the left lower lip and chin during mastication.

An In Vitro Investigation of Veneered Zirconia-Based Restorations Shade Reproducibility.

PURPOSE: To examine the effects of the veneering technique on the shade reproducibility of zirconia-based crowns. MATERIALS AND METHODS: An artificial tooth was prepared with a 1.2 mm heavy chamfer finish line and 8° taper. The prepared tooth was scanned using CAD/CAM technology to fabricate 45 cobalt chromium (CoCr) testing dies. One CoCr die was scanned, and 45 zirconia copings were milled and devided according to the veneering technique into 3 groups of 15 specimens each: layering veneering (LV) using Vita Vm9, overpressing veneering (OV) using Vita Pm9, and digital veneering (DV) using Vita Triluxe forte. All veneering layers had the same shade (A2). The specimens were cemented onto the testing dies using glass inomer cement. A spectrophotometer was used to measure the shade coordinates (L, C, h, a, b) for a Vita A2 shade tab and for each specimen. Both the CIE Lab (ΔEab ) and the CIE DE2000 (ΔE00 ) color difference formulas were applied to compare the shade tab and the study groups. One-way ANOVA and multiple comparison Bonferroni tests were applied for statistical analysis of the results. RESULTS: Means and standard deviations (SDs) of ΔEab were 2.3 ± 1.3 for LV, 3.5 ± 0.8 for OV, and 4.0 ± 0.7 for DV. Means and SDs of ΔE00 were 1.4 ± 0.8 for LV, 2.1 ± 0.5 for OV, and 3.1 ± 0.4 for DV. ΔEab of LV group was significantly lower (p < 0.05) than both OV and DV groups, whereas the difference in ΔEab between OV and DV groups was not significant (p = 0.39). The differences in ΔE00 between all groups were significant (p < 0.05). CONCLUSIONS: LV group was superior to other groups in terms of shade reproducibility. The ΔEab and the ΔE00 values of LV and OV groups were within clinically acceptable ranges; however, the ΔEab and the ΔE00 values of group DV were beyond the clinically acceptable ranges. The ΔE00 formula demonstrated a statistically significant difference between OV and the DV groups, while the ΔEab formula did not. The zirconia veneering technique had a significant influence on the shade reproducibility of zirconia-based crowns.

Veneered Zirconia-Based Restorations Fracture Resistance Analysis.

PURPOSE: To examine the effects of the veneering technique on the fracture resistance of zirconia-based crowns. MATERIALS AND METHODS: An artificial tooth was prepared with a 1.2 mm heavy chamfer finish line and 8° taper. The prepared tooth was scanned using CAD/CAM technology to fabricate 45 cobalt chromium (CoCr) testing dies. One CoCr die was scanned, and 45 zirconia copings were milled and divided according to the veneering technique into three groups of 15 specimens each: layering veneering (LV) using Vita Vm9, overpressing veneering (OV) using Vita Pm9, and digital veneering (DV) using Vita Triluxe forte. The crowns were cemented onto the testing dies using glass ionomer cement. The specimens were thermocycled (3000 cycles, 5° to 55°) then statically loaded (3.7 mm ball, 0.5 mm/min crosshead speed) until failure. Failed crowns were inspected using a magnifier, and failure patterns were identified. One-way ANOVA and multiple comparison Bonferroni tests were applied for statistical analysis of the results. RESULTS: Means and standard deviations of failure loads were 1200 ± 306 N for the LV group, 857 ± 188 N for the OV group, and 638 ± 194 N for the DV group. The differences in failure loads were statistically significant between all groups (p < 0.05). Failure mode was predominantly cohesive for LV and OV groups, whereas it was predominantly adhesive for the DV group. CONCLUSIONS: The LV group was superior to other groups in terms of fracture resistance, while the DV group was inferior to the other groups in the same aspect.

Effect of Experimental Palatal Prosthesis on Voice Onset Time.

PURPOSE: Objective evaluation of a patient's speech is needed in prosthetic dentistry because the prostheses can affect the intelligibility of speech. Measurement of voice onset time is one evaluation method of consonant production used in phonetic science. The purpose of this study was to confirm the influence of a palatal prosthesis on consonant production by measuring voice onset time. MATERIALS AND METHODS: In this study, voice onset time was measured in 10 healthy women (mean age 26.5 years) under two conditions: with and without an experimental palatal prosthesis. In this study, voice onset time of /ta/ and /ka/ were used to determine the effect of wearing a palatal prosthesis; /pa/ was tested as a control, with the null hypothesis that voice onset time of /ta/ and /ka/ would not change when wearing a palatal prosthesis. RESULTS: Medial voice onset time of /pa/, /ta/, and /ka/ syllables without the palatal prosthesis was 22.5 ms, 19.5 ms, and 42.5 ms, whereas that with the palatal prosthesis was 22.5 ms, 23.5 ms, and 55.0 ms. Voice onset times for /ta/ and /ka/ were prolonged when wearing the experimental palatal prosthesis, whereas /pa/ showed no significant difference. CONCLUSION: Consonant production was affected by wearing a palatal prosthesis, and this change in sound was detected by measuring voice onset time.

The Effect of Tissue Entrapment on Screw Loosening at the Implant/Abutment Interface of External- and Internal-Connection Implants: An In Vitro Study.

PURPOSE: To compare the removal of torque values of machined implant abutment connections (internal and external) with and without soft tissue entrapment using an in vitro model. MATERIALS AND METHODS: Thirty external- and 30 internal-connection implants were embedded in urethane dimethacrylate. Porcine tissue was prepared and measured to thicknesses of 0.5 and 1.0 mm. Six groups (n = 10) were studied: External- and internal-connection implants with no tissue (control), 0.5, and 1.0 mm of tissue were entrapped at the implant/abutment interface. Abutments were inserted to 20 Ncm for all six groups. Insertion torque values were recorded using a digital torque gauge. All groups were then immersed in 1 M NaOH for 48 hours to dissolve tissue. Subsequent reverse torque measurements were recorded. Mean and standard deviation were determined for each group, and one-way ANOVA and Bonferroni test were used for statistical analysis. RESULTS: All 60 specimens achieved a 20-Ncm insertion torque, despite tissue entrapment. Reverse torque measurements for external connection displayed a statistically significant difference (p < 0.05) between all groups with mean reverse torque values for the control (13.71 ± 1.4 Ncm), 0.5 mm (7.83 ± 2.4 Ncm), and 1.0 mm tissue entrapment (2.29 ± 1.4 Ncm) groups. Some statistically significant differences (p < 0.05) were found between internal-connection groups. In all specimens, tissue did not completely dissolve after 48 hours. CONCLUSIONS: External-connection implants were significantly affected by tissue entrapment; the thicker the tissue, the lower the reverse torque values noted. Internal-connection implants were less affected by tissue entrapment.

Analysis of buccolingual dimensional changes of the extraction socket using the "ice cream cone" flapless grafting technique.

The socket or ridge preservation approach known as the "ice cream cone" technique was used in type 2 sockets in this retrospective analysis of 11 extraction sites. A type 2 extraction socket is defined as having the presence of facial soft tissue with a partial or complete dehiscence of the buccal bone plate. All teeth were extracted atraumatically without flap elevation. A resorbable collagen membrane was contoured into an ice cream cone- shape, placed into the socket defect, and grafted with human freeze-dried bone allograft. Buccolingual dimensional changes were measured manually with a digital caliper sensitive to 0.01 mm on pre- and posttreatment casts using an acrylic template and a three-dimensional (3D) digital scanner, as well as radiographically with pre- and post-cone beam computed tomography (CBCT) scans. All implants were placed 6 months after socket preservation and achieved primary stability with a minimum torque value of 35 Ncm with a mean buccal-lingual dimensional loss of 1.32 mm. The dimensional change of the ridge from pre- to postextraction reflective of the healed grafted site ranged from a loss of 0.46 to 2.25 mm with a mean of 1.28 mm (CBCT), 0.31 to 2.71 mm with a mean of 1.36 mm (digital calipers), and 0.21 to 2.80 mm with a mean of 1.32 mm (3D digital scanner). All 11 implants were immobile and clinically osseointegrated. The so-called ice cream cone technique allows for the reconstruction of a buccal plate dehiscence to enable the placement of an implant; however, the ridge dimension was diminished by 1.32 mm compared with the width of the extraction socket prior to tooth removal.

Clinical application of stress-breaking ball attachment for implant overdenture.

PATIENT: The patient was a 62-year-old partially edentulous woman with missing bilateral premolars and molars in the mandibular jaw. The patient selected implant supported-removable partial denture rehabilitation. Implants were placed bilaterally at the distal extension of the denture base in order to minimize denture displacement. The stress-breaking ball (SBB) attachment consists of a flat-top ball head male and O-ring rubber female. The female was covered by a silicone housing with three amounts of space to allow three kinds of settlement (0.3 mm, 0.5 mm, and 0.7 mm); they were selected by thickness or pressure displacement of the mucosa and occlusal force. After the healing period, the SBB attachments (0.3 mm) were placed on the implants, and the implant-supported removable partial denture was then conventionally fabricated. The delivered denture had sufficient retention and appropriate stress breaking. DISCUSSION: The advantages of SBB attachments over conventional attachments are as follows: (1) they prevent the implant from excessive occlusal force, (2) they are ready-made, (3) they show appropriate retention, and (4) they can be easily mounted on the denture base. The disadvantages of these attachments are as follows: (1) they are approximately 1mm higher than conventional ball attachments and (2) the retentive force cannot be adjusted. CONCLUSION: The use of a stress-breaking attachment for implant overdenture rehabilitation should be considered so that the occlusal force is equally distributed between the alveolar ridge and the implants.

Combination lower lip prosthesis retained by an intraoral component.

Patients who have had a partial or full surgical resection of the maxillary or mandibular lip experience difficulties with articulation of speech, swallowing, and salivary control. This is further complicated by significant alterations in facial esthetics and lowered self-esteem. This clinical treatment will describe the fabrication of a two-piece tooth-retained maxillofacial prosthesis. An intraoral retentive portion and an extraoral section restoring lip anatomy were attached by retentive elements. This prosthesis restored the patient's esthetics, oral function, and self-esteem.

Fabrication of fixed implant prostheses using function bite impression technique (FBI technique).

PATIENT: The patient was partially edentulous, lacking both the first mandibular molars. The FBI and the conventional impression technique were used for the fabrication of implant-fixed prosthesis replacing the right and left molars, respectively. In the FBI technique, the definitive impression was made under occlusal force and functionally generated path (FGP) recording at the same time. The right and left occlusal contact areas were compared after completing the implant-fixed prosthesis rehabilitation. DISCUSSION: It has been suggested that accuracy of the impression and maxillomandibular registration is necessary to ensure a satisfactory long-term clinical outcome. The transfer of the exact position of the implants to the working cast is even more important because implants lack the mobility of natural teeth. There are displacement differences between implants and natural teeth under occlusal force. The FBI technique may compensate for this difference in accuracy. CONCLUSION: Using the FBI technique, a precise prosthesis could be produced by completing simultaneously the maxillomandibular registration, impression and FGP.

Interim prosthetic phase of multidisciplinary management of cleidocranial dysplasia: "the Bronx Approach".

This case report presents treatment of two patients with the usual characteristics of Cleidocranial Dysostosis. A multidisciplinary approach using the disciplines of prosthodontics, orthodontics, and oral surgery was effected. Exfoliation of the patient's deciduous teeth and failure of permanent anterior tooth eruption led to emotional, social, and self-esteem issues in both patients. Due to the psychosocial issues confronting these two patients, esthetics was addressed prior to active intervention with orthodontics and after some surgical intervention. The use of two interim overdenture prostheses with magnetic retention is described.

Effect of engaging abutment position in implant-borne, screw-retained three-unit fixed cantilevered prostheses.

PURPOSE: To investigate the effects of internally connected engaging component position in screw-retained fixed cantilevered prostheses. MATERIALS AND METHODS: Twenty-one three-unit fixed dental prostheses (FDPs) were cast in high-palladium alloy in three groups. In group A, engaging components were incorporated into the units away from the cantilevered segment; proximal units received nonengaging components. In group B, these positions were reversed. Control specimens were fabricated using all nonengaging components. Specimens were attached to internally connected 3.5 (diameter) × 13 mm (length) implants, torqued to 32 Ncm, and embedded into epoxy resin. Specimens were tested in cyclic fatigue with a 2 Hz sine wave and 0.1 min/max load ratio. Load amplitude started at 1.8 N and increased by 1.8 N every 60 cycles until fracture. Log-rank statistic, ANOVA, Spearman's correlation, and LIFETEST procedures were used to evaluate level of statistical significance within the results. RESULTS: In the control group, the mean number of cycles to fracture was 31,205 ± 2639. Mean axial force at fracture was 932 ± 78 N. In group A, these numbers were 38,160 ± 4292 and 1138 ± 128 N, and in group B, 31,810 ± 3408 and 949 ± 101 N. Statistical significance levels for number of cycles to fracture were: Control versus group A, p = 0.0117, and groups A versus B, p = 0.0156 (statistically significant). Control versus group B, p = 0.357 (not statistically significant). Log-rank statistic for the survival curves is greater than would be expected by chance; there was a statistically significant difference between survival curves (p = 0.012). The location and mode of failure were noteworthy (always in the abutment screw). CONCLUSIONS: The position of the engaging component had significant effects on the results. Within the limitations of this investigation, it can be concluded that using an engaging abutment in a screw-retained fixed cantilevered FDP provides a mechanical advantage, and engaging the implant furthest from the cantilever when designing a screw-retained cantilever FDP increased resistance to fracture of the distal abutment screw.

Fatigue testing of laser treated endosseous implants with an internal trilobe connection.

This study investigated the effect of laser treatment on the fatigue resistance of a 3.5-mm diameter implant with an internal trilobe connection. Twenty two implants were embedded into acrylic resin blocks. Half the specimens were used as control group, and the other half were laser treated circumferentially around the 1.5-mm polished collar with argon shielding. Implants were fatigue tested using a step-stress accelerated lifetime test in a servo-hydraulic test machine. Despite the trend pointing towards higher fatigue resistance of laser treated specimens versus controls, step-stress analysis did not determine significant differences in the fatigue lifetimes.

Laser surface treatment to improve mechanical properties of cast titanium.

OBJECTIVE: The aim of this study was to investigate the effect of laser surface treatment on the mechanical properties of cast titanium and to compare with those of the Co-Cr alloy. METHODS: Dumbbell-shaped cast specimens were prepared for commercially pure titanium (grade 2) and Co-Cr alloy. The cast titanium specimens were laser-treated on the surface using a dental Nd:YAG laser machine at 240 V and 300 V. After laser treatment, tensile testing was conducted to obtain the tensile strength, percent elongation and modulus of elasticity. The hardness depth profile was made from the cast subsurface (25 microm) to 1500 microm in depth using the cross-sections of the cast rods with the same diameter as the dumbbell. The data were statistically analyzed by ANOVA/post hoc tests (p<0.05). RESULTS: The highest tensile strength was obtained for the titanium specimens laser-treated with 300 V followed by the 240 V and the control specimens. The laser-treated titanium specimens with 300 V showed a tensile strength equivalent to the Co-Cr alloy. Although the highest modulus of elasticity was found for the specimens laser-treated with 240 V, there were no significant differences in elastic modulus among 240 V, 300 V and Co-Cr. The laser-treated groups showed significantly lower hardness at the subsurface of 25 microm and maintained their hardness until the depth of 400 microm. The hardness of the control group was very high at 25 microm depth, and dramatically decreased until the 200 microm depth. CONCLUSION: The results of tensile testing and hardness depth-profiling indicated that the laser treatment significantly improved the mechanical properties of cast titanium by improving the surface integrity of the cast surface contamination.

Implant overdenture using Konus telescope on one-piece implant: a case report.

An implant-retained Konus (tapered double crown) telescopic complete overdenture was fabricated for a mandibular edentulous patient. The Konus telescopic overdenture coping crowns and framework assembly were cast with commercially pure (CP) titanium, joined using laser welding and placed on four one-piece implants. Sufficient retention and stability were obtained using this method.

Failure probability of implant-supported restorations using highly filled all-composite crowns.

OBJECTIVES: To evaluate the effect of the surface preparation of a gold cylinder on the failure probability of highly filled all-composite restorations used as implant-supported prostheses, and to determine the effect of the location of load application. METHOD AND MATERIALS: Gold cylinders (Nobel Biocare) were prepared with 1 of 4 different surface preparations (n = 20 per surface treatment), and then an indirect resin composite (Targis, Ivoclar Vivadent) was applied. The 4 surface treatment conditions were (1) untreated (prep 1); (2) airborne-particle abraded with 50-Microm alumina (prep 2); (3) airborne-particle abraded with 50-Microm alumina followed by application of a metal conditioner (Alloy Primer, J. Morita) (prep 3); and (4) airborne-particle abraded with 50-Mum alumina followed by application of the bonding primer for the indirect resin system (Targis Link) (prep 4). A compressive load was applied vertically at 1 mm and 2 mm from the access cavity on the occlusal surface until the restorations failed. RESULTS: The prep 4 specimens had the highest fracture resistance. The fracture resistance at the 1-mm location was significantly higher than that at the 2-mm location. The failure load of the all-composite restorations with any of the surface preparations was lower than that of the resin-veneered restorations used as controls. CONCLUSION: The prep 4 conditions decreased the probability of fracture of the highly filled all-indirect resin composite restorations. Eccentric loading of the all-composite restorations should be minimized in light of the higher probability of failure associated with such a loading condition.

Use of metal conditioners to improve bond strengths of autopolymerizing denture base resin to cast Ti-6Al-7Nb and Co-Cr.

OBJECTIVE: The shear bond strengths of an autopolymerizing denture base resin to cast Ti-6Al-7Nb and Co-Cr alloys using three metal conditioners were investigated. METHODS: Ti-6Al-7Nb alloy and Co-Cr alloy discs were cast. The disc surfaces were air-abraded with 50 microm alumina particles and treated with three metal conditioners (Alloy Primer; Cesead II Opaque Primer; Metal Primer II). An autopolymerizing denture base resin was applied on the discs within a hole punched in a piece of sticky tape and a Teflon ring to define the bonding area. All specimens were immersed in 37 degrees C water for 24 h. Half of the specimens were thermocycled up to 20,000 cycles. The shear bond strengths were determined at a crosshead speed of 1.0 mm/min. RESULTS: Specimens treated with the three metal conditioners had significantly (p<0.05) improved shear bond strengths of the autopolymerizing denture base resin to both Ti-6Al-7Nb and Co-Cr. Although the bond strengths of the bonded Ti-6Al-7Nb specimens were higher than those of the Co-Cr alloy before thermocycling, the decrease in the bond strength of Ti-6Al-7Nb was considerably greater than that of the Co-Cr after thermocycling. CONCLUSION: Significant improvements in bond strength of the autopolymerizing denture base resin to cast Ti-6Al-7Nb alloy and Co-Cr alloy were achieved through the application of Alloy Primer, Cesead II Opaque Primer and Metal Primer II. The bond durability to Ti-6Al-7Nb alloy was inferior to that to Co-Cr.