ABSTRACT
Carbon is a material with interesting properties which exists in large quantities on Earth, so many studies involving carbon have been conducted. In particular, nano-sized carbon allotropes, referred to as carbon nanomaterials, comprise the subject of various studies currently underway. The electrical, chemical, physical properties of carbon nanowalls (CNWs) are modified by parameters such as surface density, height and thickness. These characteristics have significant effects on CNWs and can be adjusted as a growth interlayer. It was confirmed that the molybdenum disulfide (MoS2) interlayer synthesized in this paper by radio frequency (RF) magnetron sputtering altered the morphological characteristics of the CNWs, including its shaped edge, pores diameter and density. We provide interesting results through FE-SEM, EDS and Raman analysis in this paper. Based on the Raman analysis, both the D-peak of carbon and the ID/IG ratio decreased. Through this study, the effect of MoS2 on the morphological characteristics of CNWs was confirmed.
ABSTRACT
Recently, as air pollution and particulate matter worsen, the importance of a platform that can monitor the air environment is emerging. Especially, among air pollutants, nitrogen dioxide (NO2) is a toxic gas that can not only generate secondary particulate matter, but can also derive numerous toxic gases. To detect such NO2 gas at low concentration, we fabricated a GNWs/NiO-WO3/GNWs heterostructure-based gas sensor using microwave plasma-enhanced chemical vapor deposition (MPECVD) and sputter, and we confirmed the NO2 detection characteristics between 10 and 50 ppm at room temperature. The morphology and carbon lattice characteristics of the sensing layer were investigated using field emission scanning electron microscopy (FESEM) and Raman spectroscopy. In the gas detection measurement, the resistance negative change according to the NO2 gas concentration was recorded. Moreover, it reacted even at low concentrations such as 5-7 ppm, and showed excellent recovery characteristics of more than 98%. Furthermore, it also showed a change in which the reactivity decreased with respect to humidity of 33% and 66%.
ABSTRACT
This research is conducted in order to investigate the structural and electrical characteristics of carbon nanowalls (CNWs) according to the sputtering time of interlayers. The thin films were deposited through RF magnetron sputtering with a 4-inch target (Ni and Ti) on the glass substrates, and the growth times of the deposition were 5, 10, and 30 min. Then, a microwave plasma-enhanced chemical vapor deposition (PECVD) system was used to grow CNWs on the interlayer-coated glass substrates by using a mixture of H2 and CH4 gases. The FE-SEM analysis of the cross-sectional and planar images confirmed that the thickness of interlayers linearly increased according to the deposition time. Furthermore, CNWs grown on the Ni interlayer were taller and denser than those grown on the Ti interlayer. Hall measurement applied to measure sheet resistance and conductivity confirmed that the electrical efficiency improved significantly as the Ni or Ti interlayers were used. Additionally, UV-Vis spectroscopy was also used to analyze the variations in light transmittance; CNWs synthesized on Ni-coated glass have lower average transmittance than those synthesized on Ti-coated glass. Based on this experiment, it was found that the direct growth of CNW was possible on the metal layer and the CNWs synthesized on Ni interlayers showed outstanding structural and electrical characterizations than the remaining interlayer type.
ABSTRACT
Carbon nanowall (CNW) and carbon nanotube (CNT) were prepared as anode materials of lithium-ion batteries. To fabricate a lithium-ion battery, copper (Cu) foil was cleaned using an ultrasonic cleaner in a solvent such as trichloroethylene (TCE) and used as a substrate. CNW and CNT were synthesized on Cu foil using plasma-enhanced chemical vapor deposition (PECVD) and water dispersion, respectively. CNW and CNT were used as anode materials for the lithium-ion battery, while lithium hexafluorophosphate (LiPF6) was used as an electrolyte to fabricate another lithium-ion battery. For the structural analysis of CNW and CNT, field emission scanning electron microscope (FE-SEM) and Raman spectroscopy analysis were performed. The Raman analysis showed that the carbon nanotube in composite material can compensate for the defects of the carbon nanowall. Cyclic voltammetry (CV) was employed for the electrochemical properties of lithium-ion batteries, fabricated by CNW and CNT, respectively. The specific capacity of CNW and CNT were calculated as 62.4 mAh/g and 49.54 mAh/g. The composite material with CNW and CNT having a specific capacity measured at 64.94 mAh/g, delivered the optimal performance.
ABSTRACT
The application of a carbon nanowall (CNW) via transfer is very demanding due to the unusual structure of vertically grown wall-shaped that easily collapses. In addition, direct growth on a device cannot obtain a precision-patterned shape because of the temperature limit of the photoresist (PR). Therefore, in this paper, we demonstrate a new CNW surface micromachining technology capable of direct growth. In order to reduce unexpected damage caused by chemical etching, a physical force was used to etch with the adhesive properties of CNWs that have low adhesion to silicon wafer. To prevent compositing with PR, the CNW was surface modified using oxygen plasma. Since there is a risk of surface-modified CNW (SMCNW) collapse in an ultrasonic treatment, which is a physical force, the CNW was coated with PR. After etching the SMCNW grown on PR uncoated area, PR was lifted off using an acetone solution. The effect on the SMCNW by the lift-off process was investigated. The surface, chemical, and structural properties of PR-removed SMCNW and pristine-SMCNW were compared and showed a minimal difference. Therefore, the CNW surface micromachining technique was considered successful.
