ABSTRACT
In the direct current electric field, the surface of epoxy resin (EP) insulating material is prone to charge accumulation, which leads to electric field distortion and damages the overall insulation of the equipment. Nano-doping is an effective method to improve the surface insulation strength and DC flashover voltage of epoxy resin composites. In this study, pure bismuth ferrite nanoparticles (BFO), as well as BFO nanofillers, which were doped by La element, Cr element as well as co-doped by La + Cr element, were prepared by the sol-gel method. Epoxy composites with various filler concentrations were prepared by blending nano-fillers with epoxy resin. The morphology and crystal structure of the filler were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) tests. The effects of different filler types and filler mass fraction on the surface flashover voltage, charge dissipation rate, and trap characteristics of epoxy resin composites were studied. The results showed that element doping with bismuth ferrite nanofillers could further increase the flash voltage of the composites. The flashover voltage of La + Cr elements co-doped composites with the filler mass fraction of 4 wt% was 45.2% higher than that of pure epoxy resin. Through data comparison, it is found that the surface charge dissipation rate is not the only determinant of the flashover voltage. Appropriately reducing the surface charge dissipation rate of epoxy resin composites can increase the flashover voltage. Finally, combining with the distribution characteristics of the traps on the surface of the materials to explain the mechanism, it is found that the doping of La element and Cr element can increase the energy level depth and density of the deep traps of the composite materials, which can effectively improve the flashover voltage along the surface of the epoxy resin.
ABSTRACT
Epoxy resin (EP) has been extensively used in the field of insulation for its excellent electrical strength, mechanical property, chemical stability, and low cost. In this paper, computer molecular simulation is used to analyze the influence of nano-POSS (Nano-Polyhedral Oligomericsils Esquioxane) doping on the properties of epoxy composite from the micro point of view, which can provide a scientific basis for the optimization of the epoxy system. Two kinds of nano-POSS fillers with different mass fractions were doped into the base material of diglycidyl ether of bisphenol A (DGEBA) and 3,4-epoxycyclohexylmethyl 3,4-epoxycyclohexanecar (OSC). By molecular dynamics (MD) simulation the influence of nanofillers on the microstructure, thermal and mechanical properties of the composite were analyzed. Simulation results show that the doping of nano-POSS can improve the thermal and mechanical properties of the epoxy composite. Different nano-POSS has little effect on the glass transition temperature (Tg), coefficient of thermal expansion (CTE), and mechanical properties of the epoxy system, while the filling amount has an obvious improvement effect. Compared with EP/methyl-POSS system, the thermal and mechanical properties of the EP/phenyl-POSS system are better. At the same time, the doping of nano-POSS changed the microstructure parameters of epoxy composite. With the increase of nano-POSS filler content, fractional free volume (FFV) and mean square displacement (MSD) of both EP/POSS systems increased after the first drop. Besides, when the content of nano-POSS exceeded a certain range, the aggregation of filler itself hindered the accumulation of epoxy molecular chain segments.
Subject(s)
Doping in Sports , Epoxy Resins , Temperature , Transition TemperatureABSTRACT
Fluorescent optical fiber temperature sensors have attracted extensive attention due to their strong anti-electromagnetic interference ability, good high-voltage insulation performance, and fast response speed. The fluorescent material of the sensor probe directly determines the temperature measurement effect. In this paper, a new type of fluorescent material with a Mn2+-doped Ca2SiO4 phosphor (CSO:Mn2+) is synthesized via the solid-state reaction method at 1450 °C. The X-ray diffraction spectrum shows that the sintered sample has a pure phase structure, although the diffraction peaks show a slight shift when dopants are added. The temperature dependence of the fluorescence intensity and lifetime in the range from 290 to 450 K is explored with the help of a fluorescence spectrometer. Green emission bands peaking at 475 and 550 nm from Mn2+ are observed in the fluorescence spectra, and the intensity of emitted light decreases as the temperature rises. The average lifetime of CSO:Mn2+ is 17 ms, which is much higher than the commonly used fluorescent materials on the market. The fluorescence lifetime decreases with increasing temperature and shows a good linear relationship within a certain temperature range. The research results are of great significance to the development of a new generation of fluorescence sensors.
ABSTRACT
An investigation of the relationship between the microstructure parameters and thermomechanical properties of epoxy resin can provide a scientific basis for the optimization of epoxy systems. In this paper, the thermomechanical properties of diglycidyl ether of bisphenol A (DGEBA)/methyl tetrahydrophthalic anhydride (MTHPA) and DGEBA/nadic anhydride (NA) were calculated and tested by the method of molecular dynamics (MD) simulation combined with experimental verification. The effects of anhydride curing agents on the thermomechanical properties of epoxy resin were investigated. The results of the simulation and experiment showed that the thermomechanical parameters (glass transition temperature (Tg) and Young's modulus) of the DGEBA/NA system were higher than those of the DGEBA/MTHPA system. The simulation results had a good agreement with the experimental data, which verified the accuracy of the crosslinking model of epoxy resin cured with anhydride curing agents. The microstructure parameters of the anhydride-epoxy system were analyzed by MD simulation, including bond-length distribution, synergy rotational energy barrier, cohesive energy density (CED) and fraction free volume (FFV). The results indicated that the bond-length distribution of the MTHPA and NA was the same except for C-C bonds. Compared with the DGEBA/MTHPA system, the DGEBA/NA system had a higher synergy rotational energy barrier and CED, and lower FFV. It can be seen that the slight change of curing agent structure has a significant effect on the synergy rotational energy barrier, CED and FFV, thus affecting the Tg and modulus of the system.
ABSTRACT
Establishing the relationship among the composition, structure and property of the associated materials at the molecular level is of great significance to the rational design of high-performance electrical insulating Epoxy Resin (EP) and its composites. In this paper, the molecular models of pure Diglycidyl Ether of Bisphenol A resin/Methyltetrahydrophthalic Anhydride (DGEBA/MTHPA) and their nanocomposites containing nano-SiO2 with different particle sizes were constructed. The effects of nano-SiO2 dopants and the crosslinked structure on the micro-structure and thermomechanical properties were investigated using molecular dynamics simulations. The results show that the increase of crosslinking density enhances the thermal and mechanical properties of pure EP and EP nanocomposites. In addition, doping nano-SiO2 particles into EP can effectively improve the properties, as well, and the effectiveness is closely related to the particle size of nano-SiO2. Moreover, the results indicate that the glass transition temperature (Tg) value increases with the decreasing particle size. Compared with pure EP, the Tg value of the 6.5 Å composite model increases by 6.68%. On the contrary, the variation of the Coefficient of Thermal Expansion (CTE) in the glassy state demonstrates the opposite trend compared with Tg. The CTE of the 10 Å composite model is the lowest, which is 7.70% less than that of pure EP. The mechanical properties first increase and then decrease with the decreasing particle size. Both the Young's modulus and shear modulus reach the maximum value at 7.6 Å, with noticeable increases by 12.60% and 8.72%, respectively compared to the pure EP. In addition, the thermal and mechanical properties are closely related to the Fraction of Free Volume (FFV) and Mean Squared Displacement (MSD). The crosslinking process and the nano-SiO2 doping reduce the FFV and MSD value in the model, resulting in better thermal and mechanical properties.
ABSTRACT
Fast and accurate positioning of partial discharge (PD) sources in transformer oil is very important for the safe, stable operation of power systems because it allows timely elimination of insulation faults. There is usually more than one PD source once an insulation fault occurs in the transformer oil. This study, which has both theoretical and practical significance, proposes a method of identifying multiple PD sources in the transformer oil. The method combines the two-sided correlation transformation algorithm in the broadband signal focusing and the modified Gerschgorin disk estimator. The method of classification of multiple signals is used to determine the directions of arrival of signals from multiple PD sources. The ultrasonic array positioning method is based on the multi-platform direction finding and the global optimization searching. Both the 4 × 4 square planar ultrasonic sensor array and the ultrasonic array detection platform are built to test the method of identifying and positioning multiple PD sources. The obtained results verify the validity and the engineering practicability of this method.
