Solid-State Preparation of Metal and Metal Oxides Nanostructures and Their Application in Environmental Remediation.

Nanomaterials have attracted much attention over the last decades due to their very different properties compared to those of bulk equivalents, such as a large surface-to-volume ratio, the size-dependent optical, physical, and magnetic properties. A number of solution fabrication methods have been developed for the synthesis of metal and metal oxides nanoparticles, but few solid-state methods have been reported. The application of nanostructured materials to electronic solid-state devices or to high-temperature technology requires, however, adequate solid-state methods for obtaining nanostructured materials. In this review, we discuss some of the main current methods of obtaining nanomaterials in solid state, and also we summarize the obtaining of nanomaterials using a new general method in solid state. This new solid-state method to prepare metals and metallic oxides nanostructures start with the preparation of the macromolecular complexes chitosan·Xn and PS-co-4-PVP·MXn as precursors (X = anion accompanying the cationic metal, n = is the subscript, which indicates the number of anions in the formula of the metal salt and PS-co-4-PVP = poly(styrene-co-4-vinylpyridine)). Then, the solid-state pyrolysis under air and at 800 °C affords nanoparticles of M°, MxOy depending on the nature of the metal. Metallic nanoparticles are obtained for noble metals such as Au, while the respective metal oxide is obtained for transition, representative, and lanthanide metals. Size and morphology depend on the nature of the polymer as well as on the spacing of the metals within the polymeric chain. Noticeably in the case of TiO2, anatase or rutile phases can be tuned by the nature of the Ti salts coordinated in the macromolecular polymer. A mechanism for the formation of nanoparticles is outlined on the basis of TG/DSC data. Some applications such as photocatalytic degradation of methylene by different metal oxides obtained by the presented solid-state method are also described. A brief review of the main solid-state methods to prepare nanoparticles is also outlined in the introduction. Some challenges to further development of these materials and methods are finally discussed.

Insights of the formation mechanism of nanostructured titanium oxide polymorphs from different macromolecular metal-complex precursors.

The insight into the mechanism of the unprecedented formation of pure anatase TiO2 from the macromolecular (Chitosan)•(TiOSO4)n precursor has been investigated using micro Raman spectroscopy, Scanning Electron Microscopy (SEM) and thermogravimetric/differential thermal analysis (TGA/DTA). The formation of a graphitic film was observed upon annealing of the macromolecular precursor, reaching a maximum at about 500 °C due to decomposition of the polymeric chain of the Chitosan and (PS-co-4-PVP) polymers. The proposed mechanism is the nucleation and growth of TiO2 nanoparticles over this graphitic substrate. SEM and Raman measurements confirm the formation of TiO2 anatase around 400 °C. The observation of an exothermic peak around 260 °C in the TGA/DTA measurements confirms the decomposition of carbon chains to form graphite. Another exothermic peak around 560 °C corresponds to the loss of additional carbonaceous residues.

Solventless Preparation of Thoria and Its Inclusion into SiO2 and TiO2: A Luminescence and Photocatalysis Study.

Thoria was prepared using a solid-state method from the macromolecular precursor Chitosan·Th(NO3)4 (chitosan) and PS-co-4-PVP·Th(NO3)4 (PVP). The morphology and the average size of ThO2 depend of the chitosan and PS-co-4-PVP polymer forming the precursor. Their photoluminescent properties were investigated, finding a dependence of their intensity emission maxima, with the nature of the precursor polymer. The photocatalytic activity of ThO2 toward the degradation of methylene blue was measured for the first time, finding a degradation of about 66% in 300 min. The inclusion of ThO2 into SiO2 and TiO2 was achieved by the solid-state pyrolysis of the macromolecular composites Chitosan·Th(NO3)4//MO2 and PS-co-4-PVP·Th(NO3)4//MO2, MO2 = SiO2 or TiO2. The ThO2 exhibits a homogeneous dispersion inside the silica, showing sizes of about 40 and 50 nm for the chitosan and PVP polymer precursors, respectively. The luminescent properties of the ThO2/SiO2 and ThO2/TiO2 composites were also studied, finding a decrease in intensity when introducing the SiO2 or TiO2 matrices. The photocatalytic behavior to methylene blue degradation of ThO2 and their composites ThO2/SiO2 and ThO2/TiO2 was investigated for the first time, with them in the following order: ThO2 > ThO2/TiO2 > ThO2/SiO2.

Functionalization of Gold Nanostars with Cationic ß-Cyclodextrin-Based Polymer for Drug Co-Loading and SERS Monitoring.

Gold nanostars (AuNSs) exhibit modulated plasmon resonance and have a high SERS enhancement factor. However, their low colloidal stability limits their biomedical application as a nanomaterial. Cationic ß-cyclodextrin-based polymer (CCD/P) has low cytotoxicity, can load and transport drugs more efficiently than the corresponding monomeric form, and has an appropriate cationic group to stabilize gold nanoparticles. In this work, we functionalized AuNSs with CCD/P to load phenylethylamine (PhEA) and piperine (PIP) and evaluated SERS-based applications of the products. PhEA and PIP were included in the polymer and used to functionalize AuNSs, forming a new AuNS-CCD/P-PhEA-PIP nanosystem. The system was characterized by UV-VIS, IR, and NMR spectroscopy, TGA, SPR, DLS, zeta potential analysis, FE-SEM, and TEM. Additionally, Raman optical activity, SERS analysis and complementary theoretical studies were used for characterization. Minor adjustments increased the colloidal stability of AuNSs. The loading capacity of the CCD/P with PhEA-PIP was 95 ± 7%. The physicochemical parameters of the AuNS-CCD/P-PhEA-PIP system, such as size and Z potential, are suitable for potential biomedical applications Raman and SERS studies were used to monitor PhEA and PIP loading and their preferential orientation upon interaction with the surface of AuNSs. This unique nanomaterial could be used for simultaneous drug loading and SERS-based detection.

Incorporation of NiO into SiO2, TiO2, Al2O3, and Na4.2Ca2.8(Si6O18) Matrices: Medium Effect on the Optical Properties and Catalytic Degradation of Methylene Blue.

The medium effect of the optical and catalytic degradation of methylene blue was studied in the NiO/SiO2, NiO/TiO2, NiO/Al2O3, and NiO/Na4.2Ca2.8(Si6O18) composites, which were prepared by a solid-state method. The new composites were characterized by XRD (X-ray diffraction of powder), SEM/EDS, TEM, and HR-TEM. The size of the NiO nanoparticles obtained from the PSP-4-PVP (polyvinylpyrrolidone) precursors inside the different matrices follow the order of SiO2 > TiO2 > Al2O3. However, NiO nanoparticles obtained from the chitosan precursor does not present an effect on the particle size. It was found that the medium effect of the matrices (SiO2, TiO2, Al2O3, and Na4.2Ca2.8(Si6O18)) on the photocatalytic methylene blue degradation, can be described as a specific interaction of the NiO material acting as a semiconductor with the MxOy materials through a possible p-n junction. The highest catalytic activity was found for the TiO2 and glass composites where a favorable p-n junction was formed. The isolating character of Al2O3 and SiO2 and their non-semiconductor behavior preclude this interaction to form a p-n junction, and thus a lower catalytic activity. NiO/SiO2 and NiO/Na4.2Ca2.8(Si6O18) showed a similar photocatalytic behavior. On the other hand, the effect of the matrix on the optical properties for the NiO/SiO2, NiO/TiO2, NiO/Al2O3, and NiO/Na4.2Ca2.8(Si6O18) composites can be described by the different dielectric constants of the SiO2, TiO2, Al2O3, Na4.2Ca2.8(Si6O18) matrices. The maxima absorption of the composites (λmax) exhibit a direct relationship with the dielectric constants, while their semiconductor bandgap (Eg) present an inverse relationship with the dielectric constants. A direct relationship between λmax and Eg was found from these correlations. The effect of the polymer precursor on the particle size can explain some deviations from this relationship, as the correlation between the particle size and absorption is well known. Finally, the NiO/Na4.2Ca2.8(Si6O18) composite was reported in this work for the first time.