Preliminary Virtual Constraint-Based Control Evaluation on a Pediatric Lower-Limb Exoskeleton.

Pediatric gait rehabilitation and guidance strategies using robotic exoskeletons require a controller that encourages user volitional control and participation while guiding the wearer towards a stable gait cycle. Virtual constraint-based controllers have created stable gait cycles in bipedal robotic systems and have seen recent use in assistive exoskeletons. This paper evaluates a virtual constraint-based controller for pediatric gait guidance through comparison with a traditional time-dependent position tracking controller on a newly developed exoskeleton system. Walking experiments were performed with a healthy child subject wearing the exoskeleton under proportional-derivative control, virtual constraint-based control, and while unpowered. The participant questionnaires assessed the perceived exertion and controller usability measures, while sensors provided kinematic, control torque, and muscle activation data. The virtual constraint-based controller resulted in a gait similar to the proportional-derivative controlled gait but reduced the variability in the gait kinematics by 36.72% and 16.28% relative to unassisted gait in the hips and knees, respectively. The virtual constraint-based controller also used 35.89% and 4.44% less rms torque per gait cycle in the hips and knees, respectively. The user feedback indicated that the virtual constraint-based controller was intuitive and easy to utilize relative to the proportional-derivative controller. These results indicate that virtual constraint-based control has favorable characteristics for robot-assisted gait guidance.

Automatic Stub Avoidance for a Powered Prosthetic Leg over Stairs and Obstacles.

Passive prosthetic legs require undesirable compensations from amputee users to avoid stubbing obstacles and stairsteps. Powered prostheses can reduce those compensations by restoring normative joint biomechanics, but the absence of user proprioception and volitional control combined with the absence of environmental awareness by the prosthesis increases the risk of collisions. This paper presents a novel stub avoidance controller that automatically adjusts prosthetic knee/ankle kinematics based on suprasensory measurements of environmental distance from a small, lightweight, low-power, low-cost ultrasonic sensor mounted above the prosthetic ankle. In a case study with two transfemoral amputee participants, this control method reduced the stub rate during stair ascent by 89.95% and demonstrated an 87.5% avoidance rate for crossing different obstacles on level ground. No thigh kinematic compensation was required to achieve these results. These findings demonstrate a practical perception solution for powered prostheses to avoid collisions with stairs and obstacles while restoring normative biomechanics during daily activities.

Controlling Powered Prosthesis Kinematics over Continuous Transitions Between Walk and Stair Ascent.

One of the primary benefits of emerging powered prosthetic legs is their ability to facilitate step-over-step stair ascent by providing positive mechanical work. Existing control methods typically have distinct steady-state activity modes for walking and stair ascent, where activity transitions involve discretely switching between controllers and often must be initiated with a particular leg. However, these discrete transitions do not necessarily replicate able-bodied joint biomechanics, which have been shown to continuously adjust over a transition stride. This paper presents a phase-based kinematic controller for a powered knee-ankle prosthesis that enables continuous, biomimetic transitions between walking and stair ascent. The controller tracks joint angles from a data-driven kinematic model that continuously interpolates between the steady-state kinematic models, and it allows both the prosthetic and intact leg to lead the transitions. Results from experiments with two transfemoral amputee participants indicate that knee and ankle kinematics smoothly transition between walking and stair ascent, with comparable or lower root mean square errors compared to variations from able-bodied data.

Improving Amputee Endurance over Activities of Daily Living with a Robotic Knee-Ankle Prosthesis: A Case Study.

Robotic knee-ankle prostheses have often fallen short relative to passive microprocessor prostheses in time-based clinical outcome tests. User ambulation endurance is an alternative clinical outcome metric that may better highlight the benefits of robotic prostheses. However, previous studies were unable to show endurance benefits due to inaccurate high-level classification, discretized mid-level control, and insufficiently difficult ambulation tasks. In this case study, we present a phase-based mid-level prosthesis controller which yields biomimetic joint kinematics and kinetics that adjust to suit a continuum of tasks. We enrolled an individual with an above-knee amputation and challenged him to perform repeated, rapid laps of a circuit comprising activities of daily living with both his passive prosthesis and a robotic prosthesis. The participant demonstrated improved endurance with the robotic prosthesis and our mid-level controller compared to his passive prosthesis, completing over twice as many total laps before fatigue and muscle discomfort required him to stop. We also show that time-based outcome metrics fail to capture this endurance improvement, suggesting that alternative metrics related to endurance and fatigue may better highlight the clinical benefits of robotic prostheses.

Gait Event Detection with Proprioceptive Force Sensing in a Powered Knee-Ankle Prosthesis: Validation over Walking Speeds and Slopes.

Many powered prosthetic devices use load cells to detect ground interaction forces and gait events. These sensors introduce additional weight and cost in the device. Recent proprioceptive actuators enable an algebraic relationship between actuator torques and ground contact forces. This paper presents a proprioceptive force sensing paradigm which estimates ground reaction forces as a solution to detect gait events without a load cell. A floating body dynamic model is obtained with constraints at the center of pressure representing foot-ground interaction. Constraint forces are derived to estimate ground reaction forces and subsequently timing of gait events. A treadmill experiment is conducted with a powered knee-ankle prosthesis used by an able-bodied subject walking at various speeds and slopes. Results show accurate gait event timing, with pooled data showing heel strike detection lagging by only 6.7 ± 7.2 ms and toe off detection leading by 30.4 ± 11.0 ms compared to values obtained from the load cell. These results establish proof of concept for predicting gait events without a load cell in powered prostheses with proprioceptive actuators.

Hybrid Zero Dynamics Control for Gait Guidance of a Novel Adjustable Pediatric Lower-Limb Exoskeleton.

Exoskeleton technology has undergone significant developments for the adult population but is still lacking for the pediatric population. This paper presents the design of a hip-knee exoskeleton for children 6 to 11 years old with gait abnormalities. The actuators are housed in an adjustable exoskeleton frame where the thigh part can adjust in length and the hip cradle can adjust in the medial-lateral and posterior-anterior directions concurrently. Proper control of exoskeletons to follow nominal healthy gait patterns in a time-invariant manner is important for ease of use and user acceptance. In this paper, a hybrid zero dynamics (HZD) controller was designed for gait guidance by defining the zero dynamics manifold to resemble healthy gait patterns. HZD control utilizes a time-invariant feedback controller to create dynamically stable gaits in robotic systems with hybrid models containing both discrete and continuous dynamics. The effectiveness of the controller on the novel pediatric exoskeleton was demonstrated via simulation. The presented preliminary results suggest that HZD control provides a viable method to control the pediatric exoskeleton for gait guidance.

An Anthropometrically Parameterized Assistive Lower Limb Exoskeleton.

This paper presents an innovative design methodology for development of lower limb exoskeletons with the fabrication and experimental evaluation of prototype hardware. The proposed design approach is specifically conceived to be suitable for the pediatric population and uses additive manufacturing and a model parameterized in terms of subject anthropometrics to give a person-specific custom fit. The methodology is applied to create computer-aided design models using average anthropometrics of children 6-11 years old and using anthropometrics of an individual measured by the researchers. This demonstrates that the approach can scale to subject weight and height. A prototype exoskeleton is fabricated, which can actuate the hip and knee joints without restricting hip abduction-adduction motion. In order to test usability of the device and evaluate walking assistance, user effort is quantified in an assisted condition where the subject walks on a level treadmill with the exoskeleton powered. This is compared to an unassisted condition with the exoskeleton unpowered and a baseline condition with the subject not wearing the exoskeleton. Comparing assisted to baseline conditions, torque magnitudes increased at the hip and knee, mechanical energy generated increased at the hip but decreased at the knee, and muscle activations increased in the Vastus Lateralis but decreased in the Biceps Femoris. While the preliminary evidence for walking assistance is not entirely convincing for the tested conditions, the presented design methodology itself is promising as it has been successfully validated through the creation of computer-aided design models for children and fabrication of a serviceable exoskeleton prototype.

Gait Guidance Control for Damping of Unnatural Motion in a Powered Pediatric Lower-Limb Orthosis.

The nominal gait of each individual is unique and varies with the walking speed of the person. This poses a difficult problem for powered rehabilitative orthoses since control strategies often require a reference trajectory and give little control to the patient. This paper describes a simple control approach which applies torque resistive to joint movement that is unnatural for healthy individuals in the hip and knee joints during the swing phase of gait. The controller uses a configuration-dependent orthonormal basis to represent vectors in terms of components which are tangent and normal to healthy gait patterns for a continuum of gait speeds. The controller damps motion in the normal direction, thereby resisting movement which is unnatural for healthy individuals. With this control law, subjects are not restricted to a particular reference trajectory and have a large degree of volition over spatiotemporal gait parameters (e.g., stride length, swing time, and cadence). Experiments are conducted to check the feasibility of the control law in a provisional powered pediatric lower-limb orthosis. The gait guidance controller is used in conjunction with a human controller representing an individual with gait impairment. The main results compare gait shape quality when the gait guidance controller is enabled versus disabled, and show how the gait guidance controller is able to reshape gait to more closely resemble that of a healthy individual for various cadences.