Improvement of carrier mobility of top-gated SiC epitaxial graphene transistors using a PVA dielectric buffer layer.

The effects of treatment with polyvinyl alcohol (PVA) and a dielectric film of HfO(2) on the properties of SiC based epitaxial graphene have been explored and analyzed. We have characterized the carrier mobility of graphene on Si-face and C-face SiC with a layer of HfO(2), with or without an initial PVA treatment on the device active layer. Epitaxial graphene grown on the C-face displays a higher mobility than a film grown on the silicon face. Also, the mobility in the presence of the PVA treatment with HfO(2) dielectric layer has been improved, compared with the mobility after deposition of only gate dielectric: ∼20% in C-face graphene and ∼90% in Si-face graphene. This is a major improvement over the degradation normally observed with dielectric/graphene systems.

Electroplate and lift lithography for patterned micro/nanowires using ultrananocrystalline diamond (UNCD) as a reusable template.

A fast, simple, scalable technique is described for the controlled, solution-based, electrochemical synthesis of patterned metallic and semiconducting nanowires from reusable, nonsacrificial, ultrananocrystalline diamond (UNCD) templates. This enables the repeated fabrication of arrays of complex patterns of nanowires, potentially made of any electrochemically depositable material. Unlike all other methods of patterning nanowires, this benchtop technique quickly mass-produces patterned nanowires whose diameters are not predefined by the template, without requiring intervening vacuum or clean room processing. This technique opens a pathway for studying nanoscale phenomena with minimal equipment, allowing the process-scale development of a new generation of nanowire-based devices.

Development and characterization of on-chip biopolymer membranes.

In lab-on-a-chip applications, filtration is currently performed prior to sample loading or through pre-cast membranes adhered to the substrate. These membranes cannot be patterned to micrometer resolution, and their adhesion may be incompatible with the fabrication process or may introduce contaminants. We have developed an on-chip separation process using a biocompatible polymer that can be patterned and has controllable molecular rejection properties. We spun cast cellulose acetate (CA) membranes directly onto silicon wafers. Characterization of the molecular flux across the membrane showed that molecular weight and charge are major factors contributing to the membranes' rejection characteristics. Altering casting conditions such as polymer concentration in the casting solution and the quenching-bath composition and/or temperature allowed control of the molecular weight cut-off (MWCO). Three MWCOs; 300, 350, and 700 Da have been achieved for non-linear molecules. Molecular shape is also very important as much higher molecular weight single-stranded DNA was electrophoresed across the membranes while heme with a similar negative charge density was rejected. This was due to DNA's small molecular cross section. This is an important result because heme inhibits polymerase chain reactions (PCR) reducing the detection and characterization of DNA from blood samples.

An endothelial and astrocyte co-culture model of the blood-brain barrier utilizing an ultra-thin, nanofabricated silicon nitride membrane.

The endothelial cells comprising brain capillaries have extremely tight intercellular junctions which form an essentially impermeable barrier to passive transport of water soluble molecules between the blood and brain. Several in vitro models of the blood-brain barrier (BBB) have been studied, most utilizing commercially available polymer membranes affixed to plastic inserts. There is mounting evidence that direct contact between endothelial cells and astrocytes, another cell type found to have intimate interaction with the brain side of BBB capillaries, is at least partially responsible for the development of the tight intercellular junctions between BBB endothelial cells. However, the membranes commonly used for BBB in vitro models are lacking certain attributes that would permit a high degree of direct contact between astrocytes and endothelial cells cultured on opposing sides. This work is based on the hypothesis that co-culturing endothelial and astrocyte cells on opposite sides of an ultra-thin, highly porous membrane will allow for increased direct interaction between the two cell types and therefore result in a better model of the BBB. We used standard nanofabrication techniques to make membranes from low-stress silicon nitride that are at least an order of magnitude thinner and at least two times more porous than commercial membrane inserts. An experimental survey of pore sizes for the silicon nitride membranes suggested pores approximately 400 nm in diameter are adequate for restricting astrocyte cell bodies to the seeded side while allowing astrocyte processes to pass through the pores and interact with endothelial cells on the opposite side. The inclusion of a spun-on, cross-linked collagen membrane allowed for astrocyte attachment and culture on the membranes for over two weeks. Astrocytes and endothelial cells displayed markers specific to their cell types when grown on the silicon nitride membranes. The transendothelial electrical resistances, a measure of barrier tightness, of endothelial and astrocyte co-cultures on the silicon nitride membranes were comparable to the commercial membranes, but neither system showed synergy between the two cell types in forming a tighter barrier. This lack of synergy may have been due to the loss of ability of commercially available primary bovine brain microvascular endothelial cells to respond to astrocyte differentiating signals.