Bias Voltage Dependency of Structural and Bipolar Plate-Related Properties of Cathodic Arc-Deposited Carbon-Based Coatings.

Carbon-based coatings composed of a chromium interlayer and a carbon top layer were deposited on stainless steel substrates via cathodic arc evaporation. During the carbon deposition, the bias voltage was varied between 900 and 1 V to investigate the influence on the structural, electrical, and electrochemical properties. Raman spectroscopy indicated a dependency of the intensity ratio and G peak position on the bias voltage, which can be attributed to an alteration of the structure. Transmission electron microscopy (TEM) cross-section investigations revealed a graphite-like structure for most carbon top layers but with an increasing amount of disordered fractions, eventually resulting in an amorphous structure at 1 V. To further examine the structure, electron energy loss spectroscopy (EELS) was used. In the high-loss region, distinct π* and σ* peaks could be observed, which agree well with the TEM results. Additionally, analysis of the low-loss region showed that the 1 V carbon top layer exhibits a shifted σ plasmon peak at 20 eV corresponding to an amorphous structure. The carbon-based coatings are highly conductive with low interfacial contact resistance values between 4 and 1.5 mΩ cm2 at 150 N cm-2. From a bias voltage of 200 V, the resistance increases. To evaluate the corrosion resistance, we conducted potentiodynamic polarization tests. At first, with decreasing bias voltage, the corrosion resistance increases and then decreases for both the 100 and 1 V samples. Considering the low thickness, the coating with a carbon top layer deposited at 600 V had the best corrosion resistance. In combination with the excellent contact resistance, the 600 V sample is a highly suitable coating for metallic bipolar plates.

Physical and Geometrical Properties of Additively Manufactured Pure Copper Samples Using a Green Laser Source.

So far, copper has been difficult to process via laser powder bed fusion due to low absorption with the frequently used laser systems in the infrared wavelength range. However, green laser systems have emerged recently and offer new opportunities in processing highly reflective materials like pure copper through higher absorptivity. In this study, pure copper powders from two suppliers were tested using the same machine parameter sets to investigate the influence of the powder properties on the material properties such as density, microstructure, and electrical conductivity. Samples of different wall thicknesses were investigated with the eddy-current method to analyze the influence of the sample thickness and surface quality on the measured electrical conductivity. The mechanical properties in three building directions were investigated and the geometrical accuracy of selected geometrical features was analyzed using a benchmark geometry. It could be shown that the generated parts have a relative density of above 99.95% and an electrical conductivity as high as 100% International Annealed Copper Standard (IACS) for both powders could be achieved. Furthermore, the negative influence of a rough surface on the measured eddy-current method was confirmed.

Development of a System for Additive Manufacturing of Ceramic Matrix Composite Structures Using Laser Technology.

Ceramic matrix composites (CMCs) are refractory ceramic materials with damage-tolerant behavior. Coming from the space industry, this class of materials is increasingly being used in other applications, such as automotive construction for high-performance brake discs, furnace technology, heat coatings for pipe systems and landing flaps on reusable rocket sections. In order to produce CMC faster and more cost-efficiently for the increasing demand, a new additive manufacturing process is being tested, which in the future should also be able to realize material joints and higher component wall thicknesses than conventional processes. The main features of the process are as follows. A ceramic fiber bundle is de-sized and infiltrated with ceramic suspension. The bundle infiltrated with matrix material is dried and then applied to a body form. During application, the matrix material is melted by laser radiation without damaging the fiber material. For the initial validation of the material system, samples are pressed and analyzed for their absorption properties using integrating sphere measurement. With the results, a suitable processing laser is selected, and initial melting tests of the matrix system are carried out. After the first validation of the process, a test system is set up, and the first test specimens are produced to determine the material parameters.

Additive Manufacturing of ß-NiAl by Means of Laser Metal Deposition of Pre-Alloyed and Elemental Powders.

The additive manufacturing (AM) technique, laser metal deposition (LMD), combines the advantages of near net shape manufacturing, tailored thermal process conditions and in situ alloy modification. This makes LMD a promising approach for the processing of advanced materials, such as intermetallics. Additionally, LMD allows the composition of a powder blend to be modified in situ. Hence, alloying and material build-up can be achieved simultaneously. Within this contribution, AM processing of the promising high-temperature material ß-NiAl, by means of LMD, with elemental powder blends, as well as with pre-alloyed powders, was presented. The investigations showed that by applying a preheating temperature of 1100 °C, ß-NiAl could be processed without cracking. Additionally, by using pre-alloyed, as well as elemental powders, a single phase ß-NiAl microstructure can be achieved in multi-layer build-ups. Major differences between the approaches were found within substrate near regions. For in situ alloying of Ni and Al, these regions are characterized by an inhomogeneous elemental distribution in a layerwise manner. However, due to the remelting of preceding layers during deposition, a homogenization can be observed, leading to a single-phase structure. This shows the potential of high temperature preheating and in situ alloying to push the development of new high temperature materials for AM.

Laser Treatment as Sintering Process for Dispenser Printed Bismuth Telluride Based Paste.

Laser sintering as a thermal post treatment method for dispenser printed p- and n-type bismuth telluride based thermoelectric paste materials was investigated. A high-power fiber laser (600 W, 1064 nm) was used in combination with a scanning system to achieve high processing speed. A Design of Experiment (DoE) approach was used to identify the most relevant processing parameters. Printed layers were laser treated with different process parameters and the achieved sheet resistance, electrical conductivity, and Seebeck coefficient are compared to tube furnace processed reference specimen. For p-type material, electrical conductivity of 22 S/cm was achieved, compared to 15 S/cm in tube furnace process. For n-type material, conductivity achieved by laser process was much lower (7 S/cm) compared to 88 S/cm in furnace process. Also, Seebeck coefficient decreases during laser processing (40-70 µV/K and -110 µV/K) compared to the oven process (251 µV/K and -142 µV/K) for p- and n-type material. DoE did not yet deliver a set of optimum processing parameters, but supports doubts about the applicability of area specific laser energy density as a single parameter to optimize laser sintering process.

Material Characterization of AISI 316L Flexure Pivot Bearings Fabricated by Additive Manufacturing.

Recently, additive manufacturing (AM) by laser metal deposition (LMD) has become a key technology for fabricating highly complex parts without any support structures. Compared to the well-known powder bed fusion process, LMD enhances manufacturing possibilities to overcome AM-specific challenges such as process inherent porosity, minor build rates, and limited part size. Moreover, the advantages aforementioned combined with conventional machining enable novel manufacturing approaches in various fields of applications. Within this contribution, the additive manufacturing of filigree flexure pivots using 316L-Si by means of LMD with powder is presented. Frictionless flexure pivot bearings are used in space mechanisms that require high reliability, accuracy, and technical cleanliness. As a contribution to part qualification, the manufacturing process, powder material, and fabricated specimens were investigated in a comprehensive manner. Due to its major impact on the process, the chemical powder composition was characterized in detail by energy dispersive X-ray spectroscopy (EDX) and inductively coupled plasma optical emission spectrometry (ICP-OES). Moreover, a profound characterization of the powder morphology and flowability was carried out using scanning electron microscopy (SEM) and novel rheological investigation techniques. Furthermore, quantitative image analysis, mechanical testing, laser scanning microscopy, and 3D shape measurement of manufactured specimens were conducted. As a result, the gained knowledge was applied for the AM-specific redesign of the flexure pivot. Finally, a qualified flexure pivot has been manufactured in a hybrid manner to subsequently ensure its long-term durability in a lifetime test bench.

Analysis of Melt Pool Characteristics and Process Parameters Using a Coaxial Monitoring System during Directed Energy Deposition in Additive Manufacturing.

The growing number of commercially available machines for laser deposition welding show the growing acceptance and importance of this technology for industrial applications. Their increasing usage in research and production requires process stability and user-friendly handling. A commercially available DMG MORI LT 65 3D hybrid machine used in combination with a CCD-based coaxial temperature measurement system was utilized in this work to investigate what information relating to the intensity distribution of melt pool surfaces could be appropriate to draw conclusions about process conditions. In this study it is shown how the minimal required specific energy for a stable process can be determined, and it is indicated that the evolution of a plasma plume depends on thermal energy within the base material. An estimated melt pool area-calculated by the number of pixels (NOP) with intensities larger than a fixed, predefined threshold-builds the main measure in analysing images from the process camera. The melt pool area and its temporal variance can also serve as an indicator for an increased working distance.

Self-healing materials.

Self-healing materials are able to partially or completely heal damage inflicted on them, e.g., crack formation; it is anticipated that the original functionality can be restored. This article covers the design and generic principles of self-healing materials through a wide range of different material classes including metals, ceramics, concrete, and polymers. Recent key developments and future challenges in the field of self-healing materials are summarised, and generic, fundamental material-independent principles and mechanism are discussed and evaluated.