Cannulated versus non-cannulated cancellous screw fixation for femoral neck fractures: a synthetic bone biomechanical study.

PURPOSE: To compare the compressive strength of cannulated versus non-cannulated cancellous screws for undisplaced femoral neck fractures in synthetic bones. METHODS: 18 synthetic proximal femurs simulating an AO B1 valgus impacted femoral neck fracture in osteoporotic bone were used. The fracture angles were between 55º and 63º (Pauwels grade 2). Fixation was made using 6.5-mm non-cannulated screws (n=6), 6.5-mm cannulated screws (n=6), or 7.3-mm cannulated screws (n=6). A custom-built jig was designed to guide the insertion of the screws in an identical triangular configuration. Screws were tightened by a single operator using a torque-measuring screwdriver. The femoral head was subjected to progressive axial loading at 5 mm/min. The load to failure and displacement were recorded. RESULTS: The 3 groups did not differ significantly except that the load to failure was higher in the construct with 6.5-mm non-cannulated screws than that with 6.5-mm cannulated screws (1222 N vs 1008 N, p=0.003). CONCLUSION: The compressive strength of a synthetic bone hip fracture model fixed with non-cannulated screws was higher than that of cannulated screws of the same diameter.

An unusual case of knee locking.

Knee locking is an incapacitating condition that requires urgent orthopaedic intervention. The most common cause is meniscal injury, followed by torn anterior cruciate ligament, osteochondral loose bodies and foreign bodies in the joint space. This report describes a patient who had an unusual case of left knee locking. After clinical examination and radiological investigations, the provisional diagnosis was a lateral meniscal tear, which was not visible on magnetic resonance imaging. Diagnostic arthroscopy of the left knee revealed a 1-cm yellowish lump on the medial meniscus, and the histology revealed pigmented villonodular synovitis. The menisci and cruciate ligaments were intact.

Measurement of laxity in the anterior cruciate ligament-deficient knee: a comparison of three different methods in vitro.

The aim of this study was to compare in-vitro measurements of anteroposterior laxity in the anterior cruciate ligament (ACL)-deficient knee using three different methods: an Instron materials-testing machine, then a KT-2000 arthrometer, and finally by Roentgen stereophotogrammetric analysis (RSA). Eight ACL-deficient human cadaver knees were used. Total displacement was measured between 90 N anterior and 90 N posterior tibiofemoral drawer forces at both 20 degrees and 90 degrees knee flexion. Laxity ranged from 11.5 to 27.6 mm at 20 degrees and from 8.7 to 23.9 mm at 90degrees. A statistically significant difference was not found between the mean RSA and KT-2000 measurements. However, the mean Instron measurements of laxity were significantly (3-4 mm) higher than both RSA and KT-2000 measurements. The clinical methods of RSA and the KT-2000 measurements agreed well but appeared to underestimate tibiofemoral anteroposterior laxity compared with the materials-testing machine. These findings may be helpful in the future comparison of different studies.

Patellar resection during total knee arthroplasty: effect on bone strain and fracture risk.

Patellae in small knees, or after severe patellar erosion, may be vulnerable to fracture after resection during arthroplasty. The patellar remnant may be thin, while the polyethylene component has a standard thickness. Anterior patellar bone strain was measured in cadaver knees loaded via the quadriceps, from 0 to 90 degrees flexion, with the patella intact, and after resections to 16, 13 and 11 mm thick and replacement by an 8-mm-thick polyethylene component. Strain increased significantly with knee flexion with constant 500 N quadriceps tension. Resection caused significant changes from intact values in knee flexion and extension and no significant effect at 30 degrees flexion. In flexion, bending caused the anterior surface to become more convex, with high tensile bone strains. In extension, resection caused negative anterior strains, representing bending in the opposite direction, with large tensile strains on the cut posterior surface. For normal activities, such as rising from a chair (1.8 kN quadriceps tension) the patella appears safe against fracture with a minimal resection to 16 mm thick. An eroded patella resected to 11 mm thickness may be at risk of fracture with that loading.