Low-cost materials for swine wastewater treatment using adsorption and Fenton's process.

Untreated swine wastewater (SW) discharge leads to serious consequences such as water quality decreasing related to eutrophication and proliferation of harmful algae containing cyanotoxins, which can cause acute intoxication in humans. The use of untreated pig farming effluent as fertilizer can lead to the accumulation of polluting compounds. Biological treatments can degrade organic matter but have the disadvantage of requiring large areas and high retention times and demonstrating low efficiencies in the degradation of refractory compounds such as pharmaceutical compounds. In this ambit, the performance of four low-cost materials was evaluated for treatment of a swine wastewater using physical-chemical processes such as adsorption and Fenton's process. The tested materials are two natural resources, red volcanic rock from Canary (RVR) Islands and black volcanic rock (BVR) from Azores, and two industry residues, red mud (RM) and iron filings (IF). Among the tested materials, only IFs are catalytically active for Fenton's peroxidation. Still, RVR, BVR, and RM were efficient adsorbents removing up to 67% of COD. The combination between adsorption followed by Fenton's process using IF as catalyst showed interesting results. When RM is applied as adsorbent in the diluted effluent, it was able to remove 67% and 90% of COD for adsorption and adsorption followed by IF Fenton, respectively. At those conditions, the resultant treated effluent accomplishes the requirements for direct discharge in the natural water courses as well as the parameters for water reusing.

Nanostructured photocatalysts for the abatement of contaminants by photocatalysis and photocatalytic ozonation: An overview.

The water scarcity, the presence of different contaminants in the worldwide waters and wastewaters and their impacts should motivate their good elimination and water management. With this, photocatalysis and photocatalytic ozonation are strong solutions to obtain good quality reclaimed water, for different applications. Nanostructured supported photo-active catalysts, such as the TiO2, WO3 or ZnO can positively affect the performance of such technologies. Therefore, different semiconductors materials have been aroused the interest of the scientific community, mainly due to its functional properties as well as characteristics imposed by the different nanostructures. With this, this work overviews different works and perspective on the TiO2 nanotubes and other semiconductors nanostructures, with the analysis of different works from 2001 to 2022. Aspects as the substrate effect, electrolyte nature, aspect ratio, electrolyte aging, and annealing treatment but also the effect of morphology, anodization time, applied voltage, temperature and viscosity are discussed. Modification of TiO2 nanotubes is also presented in this paper. The main objective of this work is to present and discuss the key parameters and their effects on the anodization of different semiconductors, as well as the results obtained until today on the degradation of different contaminants by photocatalysis and photocatalytic ozonation, as well as their use on the treatment of real wastewater. TiO2 nanotubes present unique properties and highly ordered configuration, which motivate their use on photo-driven technologies for the pollutant's abatement, even when compared to other nanostructures. However, photocatalysts with activity on the visible range and solar radiation, such as the WO3, can present higher performance and can decrease operational costs, and must be an important source and a key to find efficient and cost-friendly solutions.

Unexpected effect of ozone on the paraben's mixture degradation using TiO2 supported nanotubes.

Titanium dioxide can present advantages when coupled with ozonation. Moreover, the catalytic ozonation can be enhanced by radiation. The main disadvantage of this technology is the use of a suspended catalyst entailing a separation step. Thus, catalytic ozonation was analysed using supported TiO2 nanotubes prepared by anodization at different voltages. The effect of different radiation sources on the catalytic ozonation of parabens was tested. The increase on voltage preparation led to plates with higher surface areas from 60 to 280 cm2. However, this did not improve the parabens mixture degradation during UVA photocatalytic ozonation. The use of sunlight radiation allows a significant reduction in terms of time necessary for total parabens degradation from 15 to 10 min. However, the amount of ozone required doubles. Catalytic ozonation presents worst results than single ozonation. This means that molecular ozone is the main responsible for degradation. No dissolved ozone was detected at the experiments with supported nanotubes which could mean that it was adsorbed on the catalysts surface decreasing the degradation rates. The presence of municipal wastewaters as matrix inhibited parabens degradation for both single and catalytic ozonation, mainly due to the trapping ozone effect. In fact, for the TOD of 4.5 mg/L it was just possible to remove about 80% of parabens when MWW compared to 100% when UP was used. Even so, the presence of supported nanotubes during ozonation seems to be required to reduce the toxicity of the resultant treated effluent. In fact, the wastewater luminescence inhibition decreased (from 100 to 43%) and germination index increased (from 7 to 97%) with catalytic ozonation which may enable treated water reuse.

TiO2 nanotube arrays-based reactor for photocatalytic oxidation of parabens mixtures in ultrapure water: Effects of photocatalyst properties, operational parameters and light source.

Self-organized TiO2 nanotubes as immobilized photocatalysts were evaluated in detail for the photocatalytic degradation of parabens mixtures from ultrapure water. This kind of approach can be a very suitable option for emerging contaminants degradation considering the possibility of the catalyst reuse and recovery which will be simpler than when catalytic powders are used. The anodization method was applied for the TiO2 nanotubes production under different preparation voltages (20, 30 and 40 V). These preparation conditions are important on the morphological characteristics of nanotubes such as length, as well as internal and external diameters. The photocatalytic efficiency was dependent on the materials preparation voltages. The photocatalytic oxidation was evaluated using two different irradiation sources, namely UVA and sunlight. These irradiation sources were evaluated for parabens mixture degradation using different number of catalytic plates. The increase of the number of plates improved the parabens degradation possibly due to the availability of more active sites which can be relevant for the hydroxyl radical's generation. The effect of the reactor design was also evaluated using sunlight irradiation. The configuration, position and solar concentrators can be important for the performance of degradation. The mechanism of degradation was analysed through by-products formation under sunlight irradiation. The main responsible for parabens degradation was hydroxyl radical. Decarboxylation, dealkylation and hydroxylation seem to be the most important reactional steps for the mixture decontamination.