ABSTRACT
Our research material comprised antivandal fire-retardant hybrid composites modified with inorganic and organic fillers intended for application in public transport vehicles. This paper presents an approach to studying their impact strength as a function of the composite thickness (3 to 6 mm) and striker shape (hemispherical, semicylindrical, wedge-shaped) used in the experimental stand. Group A composites, made of single fabric layers (n = 5), were thinner and their impact strength was lower by 73% than that for Group B composites made of double fabric layers. Study results show an almost threefold improvement in impact strength for a thickness increase of as little as 0.3 mm. Statistical analysis (the Shapiro-Wilk test, p > 0.05) did not show any significant differences in the quantitative evaluation of changes (n = 3) on the surface of the examined materials caused by impacts with strikers of different shapes. In turn, a linear correlation (Shapiro-Wilk test, W = 0.0857, p = 0.022) was found between impact strength and the thickness of the studied materials. It was observed that appropriate arrangement of fabrics and powder fillers can lead to a different distribution of forces and energy absorbed by the tested material. A lower impact strength was observed for the composite which had powder fillers in its composition, which caused the formation of microvoids in the structure of the material and thus led to a weakening in their strength properties. An effect of the placement of the glass fabric layer in the composite on the results was also observed. Moreover, SEM evaluation of the composites revealed their layered structure and the impregnation of woven fabrics with resin.
ABSTRACT
The aim of the study was to produce new elastomeric materials containing butyl rubber (IIR) filled with silica and phyllosilicates (vermiculite, montmorillonite, perlite or halloysite tubes) with enhanced hydrophobicity and barrier properties and reduced chemical degradation. It was found that the filler type had a significant impact on the degree of cross-linking of butyl rubber and the properties of its vulcanizates. The highest degree of cross-linking and the highest mechanical strength were achieved for IIR composites filled with Arsil with perlite or halloysite tubes. The highest surface hydrophobicity (119°) was confirmed for the IIR vulcanizates with Arsil and montmorillonite. All tested samples showed high barrier properties because both the gas diffusion rate coefficient and the permeability coefficient reached low values. Both unfilled and filled IIR vulcanizates retained chemical resistance in contact with methanol for 480 min. Hour-long contact of a polar solvent (methanol) with each of the vulcanizates did not cause material degradation, while the presence of a non-polar solvent (n-heptane) worsened the mechanical parameters by up to 80%. However, the presence of fillers reduced the chemical degradation of vulcanizates (in the case of cured IIR filled with Arsil and halloysite tubes by 40% compared to the composite without fillers).
ABSTRACT
At a time of growing epidemic hazards caused by a very rapid evolution of dangerous pathogens, there is a pressing demand for bioactive textiles. Therefore, the development of high-quality knitted structures that could be used as bioactive protective materials has become a priority. This publication describes the fabrication of functional knitted structures from previously prepared antibacterial cellulose fibers containing nanosilica with immobilized silver nanoparticles. The structural and physical parameters of knitted fabrics made from them were studied with a view to their potential application in bioactive protective gloves. Tests of the basic structural and physical parameters of the knitted fabrics did not show that the nanomodifier applied in fibers significantly impacts the physical properties of the resulting fabrics. Moreover, water vapor permeability, cut resistance, and pH test results relevant to the functional and protective properties of interest and to user comfort showed that the obtained fabrics can be used in the production of bioactive protective gloves.
ABSTRACT
It is well established that homocysteine (Hcy) and its thiolactone (HTL) are reactive towards aldehydes in an aqueous environment, forming substituted thiazinane carboxylic acids. This report provides evidence that Hcy/HTL and formaldehyde (FA) adduct, namely 1,3-thiazinane-4-carboxylic acid (TCA) is formed in vivo in humans. In order to provide definitive proof, a gas chromatography-mass spectrometry (GC-MS) based method was elaborated to identify and quantify TCA in human urine. The GC-MS assay involves chemical derivatization with isobutyl chloroformate (IBCF) in the presence of pyridine as a catalyst, followed by an ethyl acetate extraction of the obtained isobutyl derivative of TCA (TCA-IBCF). The validity of the method has been demonstrated based upon United States Food and Drug Administration recommendations. The assay linearity was observed within a 1-50 µmol L-1 range for TCA in urine, while the lowest concentration on the calibration curve was recognized as the limit of quantification (LOQ). Importantly, the method was successfully applied to urine samples delivered by apparently healthy volunteers (n = 15). The GC-MS assay may provide a new analytical tool for routine clinical analysis of the role of TCA in living systems in the near future.
