Enhancing Performance and Stability of Perovskite Solar Cells with a Novel Formamidine Group Additive.

Perovskite materials, particularly FAPbI3, have emerged as promising candidates for solar energy conversion applications. However, these materials are plagued by well-known defects and suboptimal film quality. Enhancing crystallinity and minimizing defect density are therefore essential steps in the development of high-performance perovskite solar cells. In this study, 1H-Pyrazole-1-carboximidamide hydrochloride (PCH) is introduced into FAPbI3 perovskite films. The molecular structure of PCH features a pyrazole ring bonded to formamidine (FA). The FA moiety of PCH facilitated the incorporation of this additive into the film lattice, while the negatively charged pyrazole ring effectively passivated positively charged iodine vacancies. The presence of PCH led to the fabrication of an FAPbI3 device with improved crystallinity, a smoother surface, and reduced defect density, resulting in enhanced Voc and fill factor. A record power conversion efficiency of 24.62% is achieved, along with exceptional stability under prolonged air exposure and thermal stress. The findings highlight the efficacy of PCH as a novel additive for the development of high-performance perovskite solar cells.

Flexible Aqueous Supercapacitors for Long Cycle-Life Using Electrode with Multiple Active C═S Sites.

Even though a few organic materials have attracted considerable attention for energy storage applications, their dissolution in the electrolyte during the charging-discharging processes presents a formidable challenge to their long-term performance. In this work, according to the principle of like dissolves like, non-polar trithiocyanuric acid (TCA) can effectively inhibit dissolution in an aqueous electrolyte, hence prolonging the cycle life. Moreover, theoretical calculations suggest that TCA lowers lowest unoccupied molecular orbital (LUMO) energy level, thereby promoting reaction kinetics. The CV curves of TCA maintain a rectangular structure even at a high scan rate of 1000 mV s‒1 and exhibit a remarkable capacitance retention rate of 93.1% after 50,000 cycles. Asymmetric flexible supercapacitors utilizing the TCA exhibit an impressive energy density. Moreover, they maintain 94.2% of their capacitance after undergoing 80,000 cycles. Their integration with perovskite solar cells to facilitate the rapid storage of photogenerated charges enables efficient solar energy utilization, providing a practical solution for capturing and storing renewable energy.

Designed Additive to Regulated Crystallization for High Performance Perovskite Solar Cell.

It is a crucial role for enhancing the power conversion efficiency (PCE) of perovskite solar cells (PSCs) to prepare high-quality perovskite films, which can be achieved by delaying the crystallization of perovskite film. Hence, we designed difluoroacetic anhydride (DFA) as an additive to regulating crystallization process thus reducing defect formation during perovskite film formation. It was found DFA reacts with DMSO by forming two molecules, difluoroacetate thioether ester (DTE) and difluoroacetic acid (DA). The strong bonding DTE·PbI2 and DA·PbI2 retard perovskite crystallization process for high-quality film formation, which was monitored through in situ UV-vis and PL tests. By using DFA additives, we prepared perovskite films with high-quality and low defects. Finally, a champion PCE of 25.28% was achieved with excellent environmental stability, which retained 95.75% of the initial PCE after 1152 h at 25 °C under 25% RH.

Implementation of a Multi-Functional-Group Strategy for Enhanced Performance of Perovskite Solar Cells through the Incorporation of 3-Amino-4-Phenylbutyric Acid Hydrochloride.

Reducing the defect density of perovskite films during the crystallization process is critical in preparing high-performance perovskite solar cells (PSCs). Here, a multi-functional molecule, 3-phenyl-4-aminobutyric acid hydrochloride (APH), with three functional groups including a benzene ring, ─NH3 + and ─COOH, is added into the perovskite precursor solution to improve perovskite crystallization and device performance. The benzene ring increases the hydrophobicity of perovskites, while ─NH3 + and ─COOH passivate defects related to I- and Pb2+, respectively. Consequently, the power conversion efficiency (PCE) of the optimal device increased to 24.65%. Additionally, an effective area of 1 cm2 with a PCE of 22.45% is also prepared using APH as an additive. Furthermore, PSCs prepared with APH exhibit excellent stability by 87% initial PCE without encapsulation after exposure at room temperature under 25% humidity for 5000 h and retaining 70% of initial PCE after aging at 85 °C in an N2 environment for 864 h.

2D Hybrid Perovskites: From Static and Dynamic Structures to Potential Applications.

2D perovskites have received great attention recently due to their structural tunability and environmental stability, making them highly promising candidates for various applications by breaking property bottlenecks that affect established materials. However, in 2D perovskites, the complicated interplay between organic spacers and inorganic slabs makes structural analysis challenging to interpret. A deeper understanding of the structure-property relationship in these systems is urgently needed to enable high-performance tunable optoelectronic devices. Herein, this study examines how structural changes, from constant lattice distortion and variable structural evolution, modeled with both static and dynamic structural descriptors, affect macroscopic properties and ultimately device performance. The effect of chemical composition, crystallographic inhomogeneity, and mechanical-stress-induced static structural changes and corresponding electronic band variations is reported. In addition, the structure dynamics are described from the viewpoint of anharmonic vibrations, which impact electron-phonon coupling and the carriers' dynamic processes. Correlated carrier-matter interactions, known as polarons and acting on fine electronic structures, are then discussed. Finally, reliable guidelines to facilitate design to exploit structural features and rationally achieve breakthroughs in 2D perovskite applications are proposed. This review provides a global structural landscape of 2D perovskites, expected to promote the prosperity of these materials in emerging device applications.

Surface Reconstruction for Efficient NiOx-Based Inverted Perovskite Solar Cells.

Functional agents are verified to efficiently enhance device performance of perovskite solar cells (PSCs) through surface engineering. However, the influence of intrinsic characteristics of molecules on final device performance is overlooked. Here, a surface reconstruction strategy is developed to enhance the efficiency of inverted PSCs by mitigating the adverse effects of lead chelation (LC) molecules. Bathocuproine (BCP) is chosen as the representative of LC molecules for its easy accessibility and outstanding optoelectronic properties. During this strategy, BCP molecules on perovskite surface are first dissolved in solvents and then captured specially by undercoordinated Pb2+ ions, preventing adverse n-type doping by the molecules themselves. In this case, the BCP molecule exhibits outstanding passivation effect on perovskite surface, which leads to an obviously increased open-circuit voltage (VOC). Therefore, a record power conversion efficiency of 25.64% for NiOx-based inverted PSCs is achieved, maintaining over 80% of initial efficiency after exposure to ambient condition for ≈1500 h.

Lattice Mismatch at the Heterojunction of Perovskite Solar Cells.

Lattice mismatch significantly influences microscopic transport in semiconducting devices, affecting interfacial charge behavior and device efficacy. This atomic-level disordering, often overlooked in previous research, is crucial for device efficiency and lifetime. Recent studies have highlighted emerging challenges related to lattice mismatch in perovskite solar cells, especially at heterojunctions, revealing issues like severe tensile stress, increased ion migration, and reduced carrier mobility. This review systematically discusses the effects of lattice mismatch on strain, material stability, and carrier dynamics. It also includes detailed characterizations of these phenomena and summarizes the current strategies including epitaxial growth and buffer layer, as well as explores future solutions to mitigate mismatch-induced issues. We also provide the challenges and prospects for lattice mismatch, aiming to enhance the efficiency and stability of perovskite solar cells, and contribute to renewable energy technology advancements.

Thermal Radiation Annealing for Overcoming Processing Temperature Limitation of Flexible Perovskite Solar Cells.

Common polymeric conductive electrodes, such as polyethylene terephthalate (PET) coated with indium tin oxide, face a major challenge due to their low processing-temperature limits, attributed to PET's low glass transition temperature (Tg) of (70-80 °C). This limitation significantly narrows the scope of material selection, limits the processing techniques applicable to the low Tg, and hinders the ripened technology transfer from glass substrates to them. Addressing the temperature constraints of the flexible substrates is impactful yet underexplored, with broader implications for fields beyond photovoltaics. Here, a new thermal radiation annealing methodology is introduced to address this issue. By applying the above Tg radiation annealing in conjunction with thermoelectric cooling, highly ordered molecular packing on PET substrates is successfully created, which is exclusively unachievable due to PET's low thermal tolerance. As a result, in the context of perovskite solar cells, this approach enables the circumvention of high-temperature annealing limitations of PET substrates, leading to a remarkable flexible device efficiency of 22.61% and a record fill factor of 83.42%. This approach proves especially advantageous for advancing the field of flexible optoelectronic devices.

"One-Click Restart" Recycling of Metal-Free Perovskite X-Ray Detectors.

Halide perovskites have shown great potential in X-ray detection due to outstanding optoelectronic properties. However, finding a cost-effective and environmentally sustainable method for handling end-of-life devices has remained challenging. Here, a "One-Click Restart" eco-friendly recycling strategy is introduced for end-of-life perovskite X-ray detectors. This method, utilizing water, allows for the recapture and reuse of both perovskite and conductor materials. The process is straightforward and environmentally friendly, eliminating the need for further chemical treatment, purification, additional additives or catalysts, and complex equipment. A sustainable device cycle is developed by reconstructing flexible perovskite membranes for wearable electronics from recycled materials. Large-scale, flexible membranes made from metal-free perovskite DABCO-N2H5-I3 (DABCO = N-N'-diazabicyclo[2.2.2]octonium) achieve remarkably impressive average sensitivity of 6204 ± 268 µC Gyair -1 cm-2 and a low detection limit of 102.3 nGyair s-1, which makes highly effective for X-ray imaging. The sensitivity of recycled flexible devices not only matches that of single-crystal devices made with fresh materials but also ranks as the highest among all metal-free perovskite X-ray detectors. "One-Click Restart" applies to scalable flexible devices derived from aged single-crystal counterparts, offering significant cost, time, and energy savings compared to their single-crystal equivalents. Such advantages significantly boost future market competitiveness.

Biocompatible Metal-Free Perovskite Membranes for Wearable X-ray Detectors.

Halide perovskites are emerging as promising materials for X-ray detection owing to their compatibility with flexible fabrication, cost-effective solution processing, and exceptional carrier transport behaviors. However, the challenge of removing lead from high-performing perovskites, crucial for wearable electronics, while retaining their superior performance, persists. Here, we present for the first time a highly sensitive and robust flexible X-ray detector utilizing a biocompatible, metal-free perovskite, MDABCO-NH4I3 (MDABCO = methyl-N'-diazabicyclo[2.2.2]octonium). This wearable X-ray detector, based on a MDABCO-NH4I3 thick membrane, exhibits remarkable properties including a large resistivity of 1.13 × 1011 Ω cm, a high mobility-lifetime product (µ-τ) of 1.64 × 10-4 cm2 V-1, and spin Seebeck effect coefficient of 1.9 nV K-1. We achieve a high sensitivity of 6521.6 ± 700 µC Gyair-1 cm-2 and a low detection limit of 77 nGyair s-1, ranking among the highest for biocompatible X-ray detectors. Additionally, the device exhibits effective X-ray imaging at a low dose rate of 1.87 µGyair s-1, which is approximately one-third of the dose rate used in regular medical diagnostics. Crucially, both the MDABCO-NH4I3 thick membrane and the device showcase excellent mechanical robustness. These attributes render the flexible MDABCO-NH4I3 thick membranes highly competitive for next-generation, high-performance, wearable X-ray detection applications.

Lead-Free Perovskite Single Crystal Linear Array Detector for High-Resolution X-Ray Imaging.

0D Bi-based 329-type halide perovskite is demonstrated as a promising semiconductor for X-ray detection due to its strong X-ray absorption, superior stability, availability of large single crystals (SCs) and solution processibility at low temperature. However, its low mobility-lifetime product (µτ) limits its further improvement in detection sensitivity. Based on the first-principles calculations, this work designs a new 2D Bi-based 329-type halide perovskite using a mixed-halide-induced structural dimension regulation strategy. By using a continuous supply of a precursor solution, this work successfully grows inch-sized high-quality SCs. These SCs exhibit large µτ product, high resistivity, and low ion migration. The detectors fabricated using the SCs show X-ray detection sensitivity as high as 24,509 µC Gyair -1 cm-2, short response time of 315 µs, low detection limit of 4.3 nGy s-1, and superior stability. These properties are the best among all lead-free perovskite detectors and are comparable to those of the best lead-based perovskite detectors. The linear array detector assembled on the SCs for the first time also shows a high spatial resolution of 10.6 lp mm-1 during X-ray imaging. The high performance combined with superior stability of these new 329-type lead-free halide perovskite SCs is expected to promote a new generation of X-ray detection technologies.

Anti-Solvent-Free Preparation for Efficient and Photostable Pure-Iodide Wide-Bandgap Perovskite Solar Cells.

The perovskite/silicon tandem solar cell (TSC) has attracted tremendous attention due to its potential to breakthrough the theoretical efficiency set for single-junction solar cells. However, the perovskite solar cell (PSC) designed as its top component cell suffers from severe photo-induced halide segregation owing to its mixed-halide strategy for achieving desirable wide-bandgap (1.68 eV). Developing pure-iodide wide-bandgap perovskites is a promising route to fabricate photostable perovskite/silicon TSCs. Here, we report efficient and photostable pure-iodide wide-bandgap PSCs made from an anti-solvent-free (ASF) technique. The ASF process is achieved by mixing two precursor solutions, both of which are capable of depositing corresponding perovskite films without involving anti-solvent. The mixed solution finally forms Cs0.3DMA0.2MA0.5PbI3 perovskite film with a bandgap of 1.68 eV. Furthermore, methylammonium chloride additive is applied to enhance the crystallinity and reduce the trap density of perovskite films. As a result, the pure-iodide wide-bandgap PSC delivers efficiency as high as 21.30 % with excellent photostability, the highest for this type of solar cells. The ASF method significantly improves the device reproducibility as compared with devices made from other anti-solvent methods. Our findings provide a novel recipe to prepare efficient and photostable wide-bandgap PSCs.

Defect Passivation Refinement in Perovskite Photovoltaics: Achieving Efficiency over 45% under Low-Light and Low-Temperature Dual Extreme Conditions.

Perovskite photovoltaics have emerged as the most promising candidates for next-generation light-to-electricity technology. However, their practical application still suffers from energy loss induced by intrinsic defects within the perovskite lattice. Here, a refined defect passivation in perovskite films is designed, which shows a multi-interaction mechanism between the perovskite and passivator. Interestingly, a shift of molecular bonding is observed upon cooling down the film, leading to a stronger passivation of iodine/formamidine vacancies. Such mechanism on device under low-light and low-temperature conditions is further leveraged and a record efficiency over 45% with durable ambient stability (T90 > 4000 h) is obtained. The pioneer application of perovskite solar cells in above dual extreme conditions in this work reveals the key principles of designing functional groups for the passivators, and also demonstrates the capability of perovskites for diverse terrestrial energy conversion applications in demanding environments such as polar regions and outer space.

Mechanical Durability and Flexibility in Perovskite Photovoltaics: Advancements and Applications.

The remarkable progress in perovskite solar cell (PSC) technology has witnessed a remarkable leap in efficiency within the past decade. As this technology continues to mature, flexible PSCs (F-PSCs) are emerging as pivotal components for a wide array of applications, spanning from powering portable electronics and wearable devices to integrating seamlessly into electronic textiles and large-scale industrial roofing. F-PSCs characterized by their lightweight, mechanical flexibility, and adaptability for cost-effective roll-to-roll manufacturing, hold immense commercial potential. However, the persistent concerns regarding the overall stability and mechanical robustness of these devices loom large. This comprehensive review delves into recent strides made in enhancing the mechanical stability of F-PSCs. It covers a spectrum of crucial aspects, encompassing perovskite material optimization, precise crystal grain regulation, film quality enhancement, strategic interface engineering, innovational developed flexible transparent electrodes, judicious substrate selection, and the integration of various functional layers. By collating and analyzing these dedicated research endeavors, this review illuminates the current landscape of progress in addressing the challenges surrounding mechanical stability. Furthermore, it provides valuable insights into the persistent obstacles and bottlenecks that demand attention and innovative solutions in the field of F-PSCs.

Towards High Performance: Solution-Processed Perovskite Solar Cells with Cu-Doped CH3NH3PbI3.

Perovskite solar cells (PSCs) have demonstrated remarkable photovoltaic performance, positioning themselves as promising devices in the field. Theoretical calculations suggest that copper (Cu) can serve as an effective dopant, potentially occupying interstitial sites in the perovskite structure, thereby reducing the energy barrier and enhancing carrier extraction. Subsequent experimental investigations confirm that adding CuI as an additive to MAPbI3-based perovskite cells improves optoelectronic properties and overall device performance. Optimizing the amount of Cu (0.01 M) has been found to significantly enhance crystalline quality and grain size, leading to improved light absorption and suppressed carrier recombination. Consequently, the power conversion efficiency (PCE) of Cu-doped PSCs increased from 16.3% to 18.2%. However, excessive Cu doping (0.1 M) negatively impacts morphology, resulting in inferior optical properties and diminished device performance. Furthermore, Cu-doped PSCs exhibit higher stabilized power output (SPO) compared to pristine cells. This study underscores the substantial benefits of Cu doping for advancing the development of highly efficient PSCs.

Atomic Structure and Dynamics of Organic-Inorganic Hybrid Perovskite Formamidinium Lead Iodide.

The atomic dynamic behaviors of formamidinium lead iodide [HC(NH2)2PbI3] are critical for understanding and improving photovoltaic performances. However, they remain unclear. Here, we investigate the structural phase transitions and the reorientation dynamics of the formamidinium cation [HC(NH2)2+, FA+] of FAPbI3 using neutron scattering techniques. Two structural phase transitions occur with decreasing temperature, from cubic to tetragonal phase at 285 K and then to another tetragonal at 140 K, accompanied by gradually frozen reorientation of FA cations. The nearly isotropic reorientation in the cubic phase is suppressed to reorientation motions involving a two-fold (C2) rotation along the N···N axis and a four-fold (C4) rotation along the C-H axis in the tetragonal phase, and eventually to local disordered motion as a partial C4 along the C-H axis in another tetragonal phase, thereby indicating an intimate interplay between lattice and orientation degrees of freedom in the hybrid perovskite materials. The present complete atomic structure and dynamics provide a solid standing point to understand and then improve photovoltaic properties of organic-inorganic hybrid perovskites in the future.

Kinetics Controlled Perovskite Crystallization for High Performance Solar Cells.

The power conversion efficiencies (PCEs) of perovskite solar cells have recently developed rapidly compared to crystalline silicon solar cells. To have an effective way to control the crystallization of perovskite thin films is the key for achieving good device performance. However, a paradox in perovskite crystallization is from the mismatch between nucleation and Oswald ripening. Usually, the large numbers of nucleation sites tend to weak Oswald ripening. Here, we proposed a new mechanism to promote the formation of nucleation sites by reducing surface energy from 44.9 mN/m to 36.1 mN/m, to spontaneously accelerate the later Oswald ripening process by improving the grain solubility through the elastic modulus regulation. The ripening rate is increased from 2.37 Åm ⋅ s-1 to 4.61 Åm ⋅ s-1 during annealing. Finally, the solar cells derived from the optimized films showed significantly improved PCE from 23.14 % to 25.32 %. The long-term stability tests show excellent thermal stability (the optimized device without encapsulation maintaining 82 % of its initial PCE after 800 h aging at 85 °C) and an improved light stability under illumination. This work provides a new method, the elastic modulus regulation, to enhance the ripening process.

Alkali-Metal-Assisted Green-Solvent Synthesis for In Situ Growth of Perovskite Nanocrystals in Porous Materials.

Inorganic metal halide perovskite CsPbX3 (X = I, Br, and Cl) nanocrystals (NCs) are rapidly developed due to their excellent photophysical properties and potential applications in lighting, lasers, and scintillators. However, the materials for growing perovskite NCs are insoluble or hydrolyzed in most green solvents, limiting their further development. Based on rational chemical analysis, an alkali-metal-assisted green-solvent synthesis method for in situ growth of CsPbBr3 NCs within SAPO-34 zeolite with bright luminescence is developed. Water is the only solvent used in the whole process. Surprisingly, by the synergistic effect of the channel structure of SAPO-34 and alkali-metal ions crystallization regulation, the CsPbBr3 NCs embedded in SAPO-34 assisted by Na+ emit bright blue light under ultraviolet illumination, with a 30 nm blue shift comparing to the CsPbBr3 NCs assisted by K+. Moreover, CsPbBr3 NCs can also be grown in mesoporous SiO2 SBA-15 and zeolites including ZSM-5, AlPO-5, and SOD, indicating that the method is universal for in situ growth of luminescent perovskite NCs in porous materials. This alkali-metal-assisted green-solvent synthesis provides a new strategy for developing high-quantum-yield, tunable-emission, and stable perovskite luminescent materials.

Recent Advances in Flexible Wearable Supercapacitors: Properties, Fabrication, and Applications.

A supercapacitor is a potential electrochemical energy storage device with high-power density (PD) for driving flexible, smart, electronic devices. In particular, flexible supercapacitors (FSCs) have reliable mechanical and electrochemical properties and have become an important part of wearable, smart, electronic devices. It is noteworthy that the flexible electrode, electrolyte, separator and current collector all play key roles in overall FSCs. In this review, the unique mechanical properties, structural designs and fabrication methods of each flexible component are systematically classified, summarized and discussed based on the recent progress of FSCs. Further, the practical applications of FSCs are delineated, and the opportunities and challenges of FSCs in wearable technologies are proposed. The development of high-performance FSCs will greatly promote electricity storage toward more practical and widely varying fields. However, with the development of portable equipment, simple FSCs cannot satisfy the needs of integrated and intelligent flexible wearable devices for long durations. It is anticipated that the combining an FSC and a flexible power source such as flexible solar cells is an effective strategy to solve this problem. This review also includes some discussions of flexible self-powered devices.

Highly Stretchable Conjugated Polymer/Elastomer Blend Films with Sandwich Structure.

The physical blending of high-mobility conjugated polymers with ductile elastomers provides a simple way to realize high-performance stretchable films. However, how to control the morphology of the conjugated polymer and elastomer blend film and its response to mechanical fracture processes during stretching are not well understood. Herein, a sandwich structure is constructed in the blend film based on a conjugated polymer poly[(5-fluoro-2,1,3-benzothiadiazole-4,7-diyl)(4,4-dihexadecyl-4H-cyclopenta[2,1-b:3,4-b″]dithiophene-2,6-diyl)(6-fluoro-2,1,3-benzothiadiazole-4,7-diyl)(4,4-dihexadecyl-4H-cyclopenta[2,1-b:3,4-b″]dithiophene-2,6-diyl)] (PCDTFBT) and an elastomer polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS). The sandwich structure is composed of a PCDTFBT:SEBS mixed layer laminated with a PCDTFBT-rich layer at both the top and bottom surfaces. During stretching, the external strain energy can be effectively dissipated by the deformation of the crystalline PCDTFBT domains and amorphous SEBS phases and the recrystallization of the PCDTFBT chains. This endows the blend film with excellent ductility, with a large crack onset strain exceeding 1100%, and minimized the electrical degradation of the blend film at a large strain. This study indicates that the electrical and mechanical performance of conjugated polymer/elastomer blend films can be improved by manipulating their microstructure.