Adsorption Behavior of TBPS in the Process of Cu Electrodeposition on an Au Film.

The adsorption behavior of an Cu electroplating additive, 3,3 thiobis-(1-propanesulfonic acid sodium salt) (TBPS) in a process of Cu deposition onto a single crystalline Au(111) surface is studied by an in-situ Surface-Enhanced Infrared Absorption Spectroscopy (SEIRAS). The SEIRAS spectra of the TBPS adlayer on a Cu film is investigated first and compared to that on an Au film. These results are utilized to evaluate the characteristics of TBPS adlayer on the electrode surface during the Cu deposition and stripping processes. The results show that the SEIRAS spectra of TBPS adsorbed on the Cu film resembles closely to that on the Au film, and the most pronounced peaks are symmetric S-O (ss-SO) and asymmetric S-O (as-SO) stretching modes. However, the as-SO band is sharper with a higher intensity on the Cu film. Since the ss-SO and as-SO peaks correspond to the molecular with upright and lie-down orientations, respectively, it implies that the TBPS molecules have higher ratio of lie-down orientation on the Cu film. In the Cu electrodeposition process, the cyclic voltammetry (CV) result shows that the presence of the TBPS in the HClO4 solution can decrease the inhibition effect of HClO4 to the Cu deposition. For the spectra measured at various potential during cathodic and anodic sweeping, an obvious change of the spectra occurs at ca. 0.6 V, the initiation of Cu underpotential deposition (Cu-UPD). For potentials higher and lower than 0.6 V, the spectra are similar, respectively, to those measured for the Au and Cu films. This result indicates that the TBPS molecules originally adsorbing on the Au film transfer to the surface of deposited Cu layer. This inference is also confirmed by the variation in wavenumber and peak intensity of ss-SO and as-SO peaks during the potential sweeping.

Psychometric Testing of Two Chinese-Version Scales on Attitudes Toward and Caregiving Behaviors for End-of-Life Patients and Families.

The study purpose was to examine the validities and reliabilities of the Chinese-versions Frommelt Attitudes Toward Care of the Dying Scale (Attitudes Scale) and Caregiving Behaviors Scale for End-of-Life Patients and Families (Behaviors Scale). The scales were tested in a convenience sample of 318 nurses with ≥6 months work experience at three hospitals. Cronbach's alphas of the Attitudes and Behaviors Scales were .90 and .96, respectively. Each scale had Kaiser-Meyer-Olkin index >.85 and Bartlett's test of sphericity >4000 ( p < .001). Attitudes Scale loaded on three factors: respecting and caring for dying patients and families, avoiding care of the dying, and involving patients and families in end-of-life care. The Behaviors Scale loaded on two factors: supporting dying patients and families, and helping families cope with grief. Factor loadings for both scales were ≥.49. Both Attitudes and Behaviors Scales are reliable and valid for evaluating nurses' attitudes and caregiving behaviors for the dying.

Role of peroxide ions in formation of graphene nanosheets by electrochemical exfoliation of graphite.

This study demonstrates a facile, mild and environmentally-friendly sustainable (soft processing) approach for the efficient electrochemical exfoliation of graphite using a sodium hydroxide/hydrogen peroxide/water (NaOH/H2O2/H2O) system that can produce high-quality, anodic few-layer graphene nanosheets in 95% yield at ambient reaction conditions. The control experiment conducted using NaOH/H2O revealed the crucial role of H2O2 in the exfoliation of graphite. A possible exfoliation mechanism is proposed. The reaction of H2O2 with hydroxyl ions (HO(-)) leads to the formation of highly nucleophilic peroxide ions (O2(2-)), which play a crucial role in the exfoliation of graphite via electrochemical-potential-assisted intercalation and strong expansion of graphite sheets.

Submerged liquid plasma for the synchronized reduction and functionalization of graphene oxide.

Formation of reduced and functionalized graphene oxide (r-FGO) at ambient temperature and pressure is demonstrated by generating liquid plasma submerged in acetonitrile and graphene oxide solution. The partial restoration of conjugation (sp(2) domain) and insertion of fluorophores such as nitrile and amine in r-FGO displays enhanced fluorescence property. Presence of nitrile and amine in r-FGO are confirmed by X-ray photoelectron spectroscopy and Fourier transforms infrared spectroscopy. Morphology and optical property of r-FGO are studied with transmission electron microscopy, scanning tunneling microscopy and Ultraviolet-visible spectroscopy measurements. The nitrile and amine present in r-FGO undergo a surface-controlled reversible redox reaction and sp(2)- enriched r-FGO acts as an electrical double layer, providing additional hybrid capacitance or pseudocapacitance. r-FGO shows high cyclic stability with a specific capacitance value of 349 F/g at the scan rate of 10 mV/s. Only marginal reduction of specific capacitance (<10% reduction) is observed at the end of 1000 cycles.

Self-organization of two-dimensional poly(3-hexylthiophene) crystals on Au(111) surfaces.

A novel approach to construct organized structures and tunable electronic properties of poly(3-hexylthiophene) (P3HT) monolayers on Au(111) surfaces was developed based on a self-assembly process in a liquid phase. On a bare Au(111) surface, P3HT adsorbs as a monolayer with a randomly oriented and curvy-wire morphology. When the gold surface was pre-modified by an iodine adlayer (I-Au(111)), the passivation effect of iodine decreases the substrate-adsorbate interaction. As a result, P3HT adsorbs as linear chains, stacking and folding into regular arrays of a polymer bundle. By controlling the electrode at more negative potentials, it is able to desorb the iodine adlayer from the substrate. The remaining P3HT adsorbs onto the Au(111) surface directly, retaining a linear and regular arrangement. However, a different electronic structure is imaged by scanning tunneling microscopy (STM). The scanning tunneling spectroscopy (STS) analysis reveals that this molecular image is associated with a 0.16 eV shift of the Fermi level toward HOMO position, indicating a stronger p-doping characteristic of the adlayer. The phenomenon is ascribed to an iodine-induced p-doping reaction which occurs during the desorption of iodine. This work demonstrates that electrode potential and pre-adsorbed halide adlayers can be effectively used to regulate the arrangement and electronic properties of adsorbed molecules on metallic substrates.

Adsorption and desorption of bis-(3-sulfopropyl) disulfide during Cu electrodeposition and stripping at Au electrodes.

The adsorption and desorption of bis-(3-sulfopropyl) disulfide (SPS) on Cu and Au electrodes and its electrochemical effect on Cu deposition and dissolution were examined using cyclic voltammetry stripping (CVS), field-emission scanning electron microscopy (FESEM), and X-ray photoelectron spectroscopy (XPS). SPS dissociates into 3-mercapto-1-propanesulfonate when it is contacted with Au and Cu electrodes, producing Cu(I)- and Au(I)-thiolate species. These thiolates couple with chloride ions and promote not only the reduction of Cu(2+) in Cu deposition but also the oxidation of Cu(0) to Cu(+) in Cu stripping. During Cu electrodeposition on the SPS-modified Au electrode, thiolates transfer from Au onto the Cu underpotential deposition (UPD) layer. The Cu UPD layer stabilizes a large part of the transferred thiolates which subsequently is buried by the Cu overpotential deposition (OPD) layer. The buried thiolates reappear on the Au electrode after the copper deposit is electrochemically stripped off. A much smaller part of thiolates transfers to the top of the Cu OPD layer. In contrast, when SPS preadsorbs on a Cu-coated Au electrode, almost all of the adsorbed SPS leaves the Cu surface during Cu electrochemical stripping and does not return to the uncovered Au surface. A reaction mechanism is proposed to explain these results.

Adsorption characteristics of OH-terminated alkanethiol and arenethiol on Au(111) surfaces.

Adsorption behaviors of hydroxyl-terminated alkanethiol, 3-mercapto-1-propanol (MPO), and arenethiol, 4-mercaptophenol (MPH), on Au(111) electrodes were studied by cyclic voltammetry (CV) and in situ scanning tunneling microscopy (STM). The effects of the molecular structure and the chain length on the characteristics of the self-assembled monolayers (SAMs) were investigated by comparison with the results of 11-mercapto-1-undecanol (MUO) and 6-mercapto-1-hexanol (MHO) reported in the literature. All the alkanethiol SAMs have the same coverage ratio (0.33 ML). For MUO which has a longer chain length, a hexagonal lattice, the (√3 ×√3) structure was observed. However, for shorter thiols (MHO and MPO), the adsorbed molecules exhibit different contrasts under the imaging of STM, ascribed to the different conformations of adsorbed molecules. The CV results indicated that a longer chain length triggers a SAM with higher adhesion and higher resistance to the charge transfer across a SAM. For the SAM of arenethiol, MPH, the π-π stacking interaction of the phenyl ring leads to a lower surface mobility of thiol/Au complexes, lower coverage ratio, and less uniform structure of the adlayer. Furthermore, the vacancy islands commonly observed on alkanethiol-modified Au(111) electrodes do not appear on the MPH-modified surface. Instead, 2-dimensional patch islands formed on the terrace due to the aggregation of moveable MPH/Au complexes.

Effect of chloride ions on the adsorption of 3-mercapto-1-propanesulfonic acid and bis(3-sulfopropyl)-disulfide on a Au(111) surface.

In situ scanning tunneling microscopy (STM) and cyclic voltammetry (CV) were used to study the adsorption of 3-mercapto-1-propanesulfonic acid (MPS) and bis(3-sulfopropyl)-disulfide (SPS) on Au(111) electrode in a HClO(4) aqueous solution. Chloride ions were introduced into the electrolyte solution, and their effect on the adsorption behavior of MPS and SPS was investigated. The CV results show that SPS and MPS molecules preferentially adsorb on the Au(111) surface compared to chloride ions, and furthermore, chloride ion can induce the adsorption of thiol molecules on the Au(111) surface. In the absence of chloride, no adsorption phase of SPS (or MPS) adlayer can be imaged by STM at low potentials. Raising electrode potential leads to the appearance of disordered adsorption phase at ca. 0.4 V (vs RHE) and ordered adlattices at ca. 0.8 V. In the presence of chloride, ordered adsorption structures of SPS and MPS appear at a lower potential (0.2 V), implying the enhancement effect of chloride to the thiol adsorption. It is inferred that the presence of chloride ions triggers a more positively charged gold surface, enhancing the reaction rate of thiol adsorption. Furthermore, the presence of chloride also leads to a decrease in the thiol-electrolyte interaction, due to the high solvation effect of chloride ions, which promotes the adsorption of SPS and MPS onto the Au surface. With further elevation of electrode potential, electrostatic interaction leads to coadsorption of chloride ions into the adlayer, as well as orientation changes of the ad-molecules. As a result, the ordered adlattice was disrupted and disappeared at ca. 0.5 V.

Assembly behavior and monolayer characteristics of OH-terminated alkanethiol on Au(111): in situ scanning tunneling microscopy and electrochemical studies.

Self-assembled monolayers (SAMs) of 6-mercapto-1-hexanol (MHO) on an Au(111) electrode were prepared in an electrochemical system. The adsorption behavior of MHO and the time-dependent organization of the SAM were investigated by in situ scanning tunneling microscopy (STM) and cyclic voltammetry (CV). The results show that a potential higher than 0.28 V (relative to RHE) is required to induce the adsorption of MHO. At 0.28 V, the MHO molecules adsorb in a flat-lying orientation, forming an ordered striped phase with a molecular arrangement of ([Formula: see text]). However, the adlayer is not stable at this potential. The adsorbed striped phase may recover to the herringbone feature of the gold substrate due to the desorption of adsorbed MHO. At a higher potential (0.35 V), the adlayer becomes stable and can undergo a phase evolution from the striped phase to a condensed structure, identified as c([Formula: see text]). This structure can also be described as a c(4 × 2) superlattice of a [Formula: see text] hexagonal adlattice. The surface coverage of the MHO SAM is identical to the saturated structure of an 11-mercapto-1-undecanol (MUO) SAM reported in a previous work, [Formula: see text]. However, the STM image of MHO adlayer shows a modulation in intensity, reflecting the presence of various conformations of adsorbed molecules. This result is attributed to the shorter chain length of MHO, which gives a weaker van der Waals interaction between adsorbed molecules. This effect also results in a higher charge permeability across the adlayer and a lower striping potential to an MHO SAM.