Ultrafast measurement of laser-induced shock waves.

We present measurements of laser-induced shockwave pressure rise time in liquids on a sub-nanosecond scale, using custom-designed single-mode fiber optic hydrophone. The measurements are aimed at the study of the shockwave generation process, helping to improve the effectiveness of various applications and decrease possible accidental damage from shockwaves. The developed method allows measurement of the fast shockwave rise time as close as 10 µm from an 8 µm sized laser-induced plasma shockwave source, significantly improving the spatial and temporal resolution of the pressure measurement over other types of hydrophones. The spatial and temporal limitations of the presented hydrophone measurements are investigated theoretically, with actual experimental results agreeing well with the predictions. To demonstrate the capabilities of the fast sensor, we were able to show that the shockwave rise time is linked to liquid viscosity exhibiting logarithmic dependency in the low viscosity regime (from 0.4 cSt to 50 cSt). Additionally, the shockwave rise time dependency on propagation distance close to the source in water was investigated, with shock wave rise times measured down to only 150 ps. It was found that at short propagation distances in water halving the shock wave peak pressure results in the rise time increase by approximately factor of 1.6. These results extend the understanding of shockwave behavior in low viscosity liquids.

Multi-frame multi-exposure shock wave imaging and pressure measurements.

Shock wave visual detection was traditionally performed using streak cameras, limited to homogeneous shock wave emission, with the corresponding shock wave pressure measurements available at rather large distances or numerically estimated through equation of state for water. We demonstrate a multi-frame multi-exposure shock wave velocity measurement technique for all in-plane directions of propagation, based on custom-built illumination system allowing multiple illumination pulses within each frame at multi-MHz frame rates and at up to 200 MHz illumination pulse repetition frequency at sub-nanosecond pulse durations. The measurements are combined and verified using a fiber-optic probe hydrophone, providing independent shock wave pressure and time-of-flight measurements, creating a novel all-optical measurement setup. The measured pressures at distances around 100 µm from the plasma center exceed 500 MPa, while camera-based measurements at even shorter distances indicate pressures above 1 GPa.

Localized Measurement of a Sub-Nanosecond Shockwave Pressure Rise Time.

In a growing number of applications, fast and localized pressure measurement in aqueous media is desired. To perform such measurements, a custom-made single-mode fiber-optic probe hydrophone (FOPH) was designed and used to measure the pressure pulse generated by laser-induced breakdown (LIB) in water. The sensor enabled sub-nanosecond pressure rise time measurement. Both the rise time and the duration of the shockwave were found to be shorter in the direction perpendicular to the breakdown generating laser beam, compared to the shockwave observed in the parallel direction. Simultaneous high-frame-rate imaging was used to qualitatively validate the novel hydrophone data and to observe the shockwave evolution. The measurements were performed also on pressure pulses emitted during the generation of miniature ( [Formula: see text] diameter) laser-induced bubbles at very small distances (down to [Formula: see text]), further demonstrating the capabilities of the small-size sensor and the ability to measure locally. The results improve understanding of LIB shockwave characteristics dependence on laser pulse energy and duration.

Cavitation bubble dynamics in a vicinity of a thin membrane wetted by different fluids.

Understanding and controlling the interaction of cavitation bubbles and nearby material is becoming essential optimization of various processes. We examined the interaction of a single bubble with a membrane with different fluids on each side of it. Significant differences in bubble behavior depending on the fluid properties were observed, while the influence of membrane properties was less pronounced. The study has important implications, such as optimization of sonoporation (targeted drug delivery) where the mechanism, by which the permeability of the membrane is increased, is still not well understood. These results show that the focus of the optimization process should, in the first place, lie on the properties of liquids, rather than the mechanical properties of the membrane itself.

Coupled modelling approach for optimization of bifacial silicon heterojunction solar cells with multi-scale interface textures.

For advanced optical analysis and optimization of solar cell structures with multi-scale interface textures, we applied a coupled modelling approach (CMA), where we couple the rigorous coupled wave analysis method with ray tracing and transfer matrix method. Coupling of the methods enables accurate optical analysis of solar cells made of thin coherent and thick incoherent layers and includes combinations of nano- and micro-scale textures at various positions in the structure. The approach is experimentally validated on standalone single- and both-side textured crystalline silicon wafers, as well as on complete silicon heterojunction (Si HJ) solar cell structures. Using CMA, fully encapsulated bifacial Si HJ solar cells are optically simulated first by applying single- and both-side illumination, and the effects of introducing nano inverted pyramids and random micro-pyramids at front and/or rear interfaces are analyzed. Secondly, an external light management foil with a three-sided pyramidal micro-texture is applied in simulations to the front and/or rear encapsulation glass, and the related improvements are quantified. For the optimal combination of internal textures in the analyzed structure (random micro-pyramids at the front and nano inverted pyramids at the back) and the use of the light management foil on both sides of the device, a 5.6% gain in the short-circuit current is predicted, compared to the reference case with no light management foil and with random micro-pyramids applied to the front and rear internal interfaces.

Performance analysis of rigorous coupled-wave analysis and its integration in a coupled modeling approach for optical simulation of complete heterojunction silicon solar cells.

A variety of light management structures have been introduced in solar cells to improve light harvesting and further boost their conversion efficiency. Reliable and accurate simulation tools are required to design and optimize the individual structures and complete devices. In the first part of this paper, we analyze the performance of rigorous coupled-wave analysis (RCWA) for accurate three-dimensional optical simulation of solar cells, in particular heterojunction silicon (HJ Si) solar cells. The structure of HJ Si solar cells consists of thin and thick layers, and additionally, micro- and nano-textures are also introduced to further exploit the potential of light trapping. The RCWA was tested on the front substructure of the solar cell, including the texture, thin passivation and contact layers. Inverted pyramidal textures of different sizes were included in the simulations. The simulations rapidly converge as long as the textures are small (in the (sub)micrometer range), while for larger microscale textures (feature sizes of a few micrometers), this is not the case. Small textures were optimized to decrease the reflectance, and consequently, increase the absorption in the active layers of the solar cell. Decreasing the flat parts of the texture was shown to improve performance. For simulations of structures with microtextures, and for simulations of complete HJ Si cells, we propose a coupled modeling approach (CMA), where the RCWA is coupled with raytracing and the transfer matrix method. By means of CMA and nanotexture optimization, we show the possible benefits of nanotextures at the front interface of HJ Si solar cells, demonstrating a 13.4% improvement in the short-circuit current density with respect to the flat cell and 1.4% with respect to the cell with double-sided random micropyramids. We additionally demonstrate the ability to simulate a combination of nano- and microtextures at a single interface, although the considered structure did not show an improvement over the pyramidal textures.