ABSTRACT
In this work, an experimental analysis of the performance of different types of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror is presented. These artificially-controlled backscattering fiber reflectors are used in short linear cavity fiber lasers. In particular, laser emission and sensor application features are analyzed when employing optical tapered fibers, micro-drilled optical fibers and 50 µm-waist or 100 µm-waist micro-drilled tapered fibers (MDTF). Single-wavelength laser with an output power level of about 8.2 dBm and an optical signal-to-noise ratio of 45 dB were measured when employing a 50 µm-waist micro-drilled tapered optical fiber. The achieved temperature sensitivities were similar to those of FBGs; however, the strain sensitivity improved more than one order of magnitude in comparison with FBG sensors, attaining slope sensitivities as good as 18.1 pm/µÎµ when using a 50 µm-waist MDTF as distributed reflector.
ABSTRACT
A hybrid Raman-erbium random fiber laser with a half-open cavity assisted by chirped artificially controlled backscattering fiber reflectors is presented. A combination of a 2.4 km-long dispersion compensating fiber with two highly erbium-doped fiber pieces of 5 m length were used as gain media. A single random laser emission line centered at 1553.8 nm with an optical signal to noise ratio of 47 dB were obtained when pumped at 37.5 dBm. A full width at half maximum of 1 nm and a 100% confidence level output power instability as low as 0.08 dB were measured. The utilization of the new laser cavity as a temperature and strain sensor is also experimentally studied.
ABSTRACT
In this work, an interferometric sensor has been interrogated 290 km away from the monitoring station, reaching the longest distance in fiber optic sensing up to date. This has been attained by employing a double-pumped random distributed feedback fiber laser as the light source for a fiber optic low-coherence interferometry scheme. Additionally, the capability of the system to achieve coherence multiplexing for ultra-long range measurements (up to 270 km) has been proved, without presenting crosstalk between the sensors. The use of coherence multiplexing together with a random distributed feedback fiber laser addresses two of the main limitations of long-range sensing setups: their limited multiplexing capability and the need to reach the maximum monitoring distance.
ABSTRACT
We have developed a watt-level random laser at 532 nm. The laser is based on a 1064 nm random distributed ytterbium (Yb) gain-assisted fiber laser seed with a 0.35 nm linewidth and 900 mW polarized output power. A study for the optimal length of the random distributed mirror was carried out. A Yb-doped fiber master oscillator power amplifier architecture is used to amplify the random seeder laser without additional spectral broadening up to 20 W. By using a periodically poled lithium niobate crystal in a single-pass configuration, we generate in excess of 1 W random laser at 532 nm by second-harmonic generation (SHG) with an efficiency of 9%. The green random laser exhibits an instability <1%, an optical signal-to-noise ratio >70 dB, a 0.1 nm linewidth, and excellent beam quality.
ABSTRACT
A real-time switchable and reconfigurable multiwavelength laser has been experimentally carried out. The laser cavity is based on a random distributed mirror and a novel real-time reconfigurable filter mirror structure. The proposed laser has been demonstrated to generate any combination of wavelengths at the 50 and 100 GHz International Telecommunications Union (ITU) grids specifications. By simultaneously using Er-doped fiber and Raman amplification, a 15 nm wide lasing window at the C band can be utilized to create up to 18 different lasing wavelengths into the ITU grid that can be switched automatically and in real time when desired.
ABSTRACT
A characterization of a modulated random mirror laser has been experimentally carried out. Unlike conventional internally modulated fiber lasers, no distortion of the modulating frequency or self-mode-locking effects were measured. The behavior of the laser using pulsed and analog modulation up to 12 GHz is shown.
ABSTRACT
A narrow filtering technique based on the spectral overlapping of two uniform FBGs and applied to obtain a Single Longitudinal Mode (SLM) laser is proposed and demonstrated in this work. The two FBGs are spectrally detuned to reduce their coincident reflection response narrowing the equivalent filter bandwidth. A proof-of-concept linear laser has been built and tested exhibiting SLM operation even with temperature and strain variations.
Subject(s)
Filtration/instrumentation , Lasers , Refractometry/instrumentation , Surface Plasmon Resonance/instrumentation , Computer Simulation , Computer-Aided Design , Equipment Design , Equipment Failure Analysis , Models, TheoreticalABSTRACT
A sensing system for micro-displacement measurement based in a suspended-core fiber Sagnac interferometer is presented. The suspended-core fiber characterization was made through the use of an optical backscatter reflectometer, screening its multimodal and birefringent behavior. Its sensitivity to displacement measurements is shown to be due only to birefringence, being that core-cladding mode coupling is negligible. High precision (~0.45 µm) was obtained using three different measurement instruments, showing an extremely high stability and high insensitivity to temperature, demonstrating that the sensing system has the ability for low cost applications.
ABSTRACT
A 253 km ultralong remote displacement sensor system based on a fiber loop mirror interrogated by a commercial optical time-domain reflectometer is proposed and experimentally demonstrated. The use of a fiber loop mirror increases the signal-to-noise ratio, allowing the system to interrogate sensors placed 253 km away from the monitoring system without using any optical amplification. The displacement sensor was based on a long period grating spliced inside of the loop mirror, which modifies the mirror reflectivity accordingly to the applied displacement.
ABSTRACT
In the present work, a multiwavelength fiber laser based in the combination of a double-random mirror and a suspended-core Sagnac interferometer is presented. The double-random mirror acts by itself as a random laser, presenting a 30dB SNR, as result of multiple Rayleigh scattering events produced in the dispersion compensating fibers by the Raman amplification. The suspended-core fiber Sagnac interferometer provides the multi peak channeled spectrum, which can be tuned by changing the length of the fiber. The result of this combination is a stable multiwavelength peak laser with a minimum of ~25dB SNR, which is highly sensitive to polarization induced variations.
ABSTRACT
An amplitude-phase-conversion self-referencing technique for intensity-modulated photonic sensors that uses two different-wavelength fiber Bragg gratings is presented. With this technique, the system response has been demonstrated to be almost unafffected by network power variations as high as 90% of the total power launched by the source. We prove the multiplexing capability of this type of self-referenced fiber sensor by wavelength-division multiplexing two of them in a star network. A tunable fused biconical wavelength-division multiplexer is used for sensor addressing at the detection block, providing both good isolation and low cross-talk values.
ABSTRACT
A new, to our knowledge, modulator based on a tapered single-mode optical fiber is introduced. The electro-optic device consists of a tapered optical fiber placed on a resonator made of a piezoelectric material. An electrical signal applied to the piezoelectric material makes the taper bend, and that displacement produces a modulation in the intensity of the optical signal traveling through the fiber. This device is very easy to build and is low in cost. Because of its nature, this new device might be very useful in optical fiber sensors. Its performance is analyzed, and the results are discussed.
ABSTRACT
Ultrasonic non-destructive testing systems designed to control huge structures normally use several transducers in the reception stage. To avoid increasing the cost of electronics, a multiplexer is used to send all received signals to the same processing module. Traditionally, transmission of such signals is carried out using copper cables. For special applications (i.e. continuous monitoring of nuclear plants) metallic cables are not suitable because of their high sensitivity to electromagnetic perturbations. Moreover, the multiplexing is made electronically. When the distance between the transducers and the reception unit is large and/or electromagnetic noise is important, signal degradation takes place. The proposed system implements the transmission and multiplexing of ultrasonic electrical signals obtained by means of broadband transducers (up to 1 MHz), using an optical fiber. Optical fibers are made of dielectric materials (silica or plastic) so they are inherently passive to electromagnetic noise. Wavelength division multiplexing is utilized for adding channels to the system by means of fiber optic couplers and different light sources. The wavelengths of the optical signals utilized are located far apart in the optical spectrum in order to avoid serious crosstalk in transmission. The limit to the number of multiplexed channels depends on the optical fiber selected, the spectrum of the light sources and the wavelength division multiplexers or couplers utilized.
ABSTRACT
Two different optical fiber bus networks are compared and demonstrated experimentally as means of gathering information from four wavelength-division-multiplexed photonic sensors. Both topologies include distributed amplification, which allows one to overcome the limitation in the maximum number of sensors that can be multiplexed in a single structure. Results obtained with a dual-bus topology are compared with those achieved with a single-bus network.
ABSTRACT
An optical fiber power-delivery system has been developed. An analysis of the spectral response of every component in the system has been carried out. Experimental measurements of the system are presented. We obtained 205 mW of power (5.4 V, 38.3 mA), yielding 27.4% efficiency. As an application, a sensor module is optically powered. This is an electrically isolated system, inasmuch as it also sends the measured data through a fiber. Several other applications are envisaged in the fields of aerospace, avionics, and domotics.
ABSTRACT
A novel method of analysis of double-parallel amplified recirculating optical-delay lines (DPAROD) is presented. The location of the maxima and the minima of the transfer function for this configuration is calculated and experimentally demonstrated. The influence of different parameters, such as the coupling coefficients, gains, lengths of the fiber loops and fractional losses of the directional couplers, on the shape of the transfer function are analyzed. Different measurements have been taken to verify this model. The potential application of these interconnected delay loops as filters is a reason for developing this method.
