ABSTRACT
(1) Many biomechanical studies are performed using fresh frozen cadavers or embalmed specimens, although the biomechanical characteristics do not match the characteristics of in vivo tendons. Therefore, a fresh in vivo-like cadaver model has been introduced recently. As a limitation for studies with fresh cadavers, rigor mortis must be considered. The aim of this study was to evaluate the impact of the biomechanical properties and time of occurrence of rigor mortis in a fresh cadaver model. (2) For this study, 15 fresh porcine cadaver shoulders were used in an established biomechanical in vitro model to evaluate the onset of rigor mortis. Measurements took place at ten points of time (t1-t10) beginning 103 min post mortem (pm). The mobility of the supraspinatus tendon was measured in Newton (N) with a modified sensor-enhanced arthroscopic grasper. (3) The mean load measured at the time point t1 was 28.0 ± 11.2 N. The first significant decrease of mobility occurred 151 min post mortem (t4) at a mean load of 30.2 ± 13.7 N. From 227 min pm to 317 min pm, there was no further significant increase. (4) Tendon mobility decreases significantly within the first three hours after the killing. Therefore, reliable results can be obtained within 150 min post mortem before the onset of rigor mortis alters the biomechanical properties.
ABSTRACT
INTRODUCTION: The interval slide procedure (IS) has been introduced to improve mobility in massive, retracted rotator cuff tears. As clinical studies showed controversial results, the benefit of the IS is still widely discussed. AIM: Aim of this study was to analyze the effect of IS procedure on tendon mobility in a fresh porcine cadaver model. MATERIALS AND METHODS: In 30 fresh porcine cadaver shoulders with artificial supraspinatus defect tendon mobility was tested by measuring the load (in N) during tendon reduction to the footprint at the greater tubercle using a sensor enhanced arthroscopic grasper (t1). In intervention group (N = 15) anterior IS (t2), posterior IS (t3) and intraarticular capsule release (t4) were successively performed, each followed by tendon mobility assessment. Tendon mobility of the control group (N = 15) was measured in same time schedule without intervention. RESULTS: Mobility did not differ between groups for native tendons (CG 28.0 ± 11.2 N vs. IG 26.6 ± 11.6 N; P = 0.75). IS procedure significantly improves mobility at about 25.2% (t1 26.6 ± 11.6 N vs. t4 19.9 ± 12.3 N; P < 0.001) compared to the native tendon and 34.1% compared to CG (CG 30.2 ± 13.7 N vs. 19.9 ± 12.3 N; P = 0.026). In posthoc analyzes, anterior IS (P < 0.001) and capsule release (P = 0.005) significantly increased mobility, whereas the posterior IS did not (P = 0.778). CONCLUSION: The IS procedure results in increased supraspinatus tendon mobility in fresh porcine cadaver shoulders. However, performing the posterior IS subsequent to the anterior IS no significant improvement of mobility has been observed.
Subject(s)
Rotator Cuff Injuries , Tendon Injuries , Animals , Biomechanical Phenomena , Cadaver , Rotator Cuff/surgery , Rotator Cuff Injuries/surgery , Swine , Tendon Injuries/surgeryABSTRACT
Tendon mobility is highly relevant in rotator cuff surgery. Objective data about rotator cuff mobility is rare. Tendon mobility still needs to be evaluated subjectively by the surgeon. This study aims to establish a porcine animal model for mobility analysis of the supraspinatus. In this context, we introduce a sensor-enhanced, arthroscopic grasper (SEAG) suitable for objective intraoperative measurements of tendon mobility in clinical praxis. Tendon mobility of 15 fresh porcine cadaver shoulders with artificial rotator cuff tears was evaluated using the SEAG. Mobility characteristics (load-displacement curves, maximum load, stiffness) were studied and inter- and intraobserver agreement (intraclass correlation coefficient (ICC)) were tested. Factors with a potential adverse effect (plastic deformation and rigor mortis) were also evaluated. All shoulders showed characteristic reproducible load-displacement curves with a nonlinear part at the start, followed by a linear part. Mean maximum load was 28.6 N ± 12.5. Mean stiffness was 6.0 N/mm ± 2.6. We found substantial interobserver agreement (ICC 0.672) and nearly perfect intraobserver agreement (0.944) for maximum load measurement. Inter- (0.021) and intraobserver (0.774) agreement for stiffness was lower. Plastic deformation and rigor mortis were excluded. The animal model demonstrates reliable and in vivo-like measurements of tendon mobility. The SEAG is a reliable tool for tendon mobility assessment.
