Metformin Hydrochloride and Sitagliptin Phosphate Fixed-Dose Combination Product Prepared Using Melt Granulation Continuous Processing Technology.

The development of oral solid dosage forms, such as tablets that contain a high dose of drug(s), requires polymers and other additives to be incorporated at low levels as possible, to keep the final tablet weight low, and, correspondingly, the dosage form size small enough to be acceptable from a patient perspective. Additionally, a multi-step batch-based manufacturing process is usually required for production of solid dosage forms. This study presents the development and production, by twin-screw melt granulation technology, of a high-dose immediate-release fixed-dose combination (FDC) product of metformin hydrochloride (MET) and sitagliptin phosphate (SIT), with drug loads of 80% w/w and 6% w/w, respectively. For an 850/63 mg dose of MET/SIT, the final weight of the caplets was approximately 1063 mg compared with 1143 mg for the equivalent dose in Janumet®, the marketed product. Mixtures of the two drugs and polymers were melt-granulated at temperatures below the individual melting temperatures of MET and SIT (231.65 and 213.89°C, respectively) but above the glass transition temperature or melting temperature of the binder(s) used. By careful selection of binders, and processing conditions, direct compressed immediate-release caplets with desired product profiles were successfully produced. The melt granule formulations before compression showed good flow properties, were larger in particle size than individual starting API materials and were easily compressible. Melt granulation is a suitable platform for developing direct compressible high-dose immediate-release solid dosage forms of FDC products.

Engineering of pharmaceutical cocrystals in an excipient matrix: Spray drying versus hot melt extrusion.

The comparison of spray drying versus hot melt extrusion (HME) in order to formulate amorphous solid dispersions has been widely studied. However, to the best of our knowledge, the use of both techniques to form cocrystals within a carrier excipient has not previously been compared. The combination of ibuprofen (IBU) and isonicotinamide (INA) in a 1:1 M ratio was used as a model cocrystal. A range of pharmaceutical excipients was selected for processing - mannitol, xylitol, Soluplus and PVP K15. The ratio of cocrystal components to excipient was altered to assess the ratios at which cocrystal formation occurs during spray drying and HME. Hansen Solubility Parameter (HSP) and the difference in HSP between the cocrystal and excipient (ΔHSP) was employed as a tool to predict cocrystal formation. During spray drying, when the difference in HSP between the cocrystal and the excipient was large, as in the case of mannitol (ΔHSP of 18.3 MPa0.5), a large amount of excipient (up to 50%) could be incorporated without altering the integrity of the cocrystal, whereas for Soluplus and PVP K15, where the ΔHSP was 2.1 and 1.6 MPa0.5 respectively, the IBU:INA cocrystal alone was only formed at a very low weight ratio of excipient, i.e. cocrystal:excipient 90:10. Remarkably different results were obtained in HME. In the case of Soluplus and PVP K15, a mixture of cocrystal with single components (IBU and INA) was obtained even when only 10% excipient was included. In conclusion, in order to reduce the number of unit operations required to produce a final pharmaceutical product, spray drying showed higher feasibility over HME to produce cocrystals within a carrier excipient.

Pharmaceutical solvates, hydrates and amorphous forms: A special emphasis on cocrystals.

Active pharmaceutical ingredients (APIs) may exist in various solid forms, which can lead to differences in the intermolecular interactions, affecting the internal energy and enthalpy, and the degree of disorder, affecting the entropy. Differences in solid forms often lead to differences in thermodynamic parameters and physicochemical properties for example solubility, dissolution rate, stability and mechanical properties of APIs and excipients. Hence, solid forms of APIs play a vital role in drug discovery and development in the context of optimization of bioavailability, filing intellectual property rights and developing suitable manufacturing methods. In this review, the fundamental characteristics and trends observed for pharmaceutical hydrates, solvates and amorphous forms are presented, with special emphasis, due to their relative abundance, on pharmaceutical hydrates with single and two-component (i.e. cocrystal) host molecules.